Top

The International Journal of Advanced Manufacturing Technology

Published in:

14-07-2020 | ORIGINAL ARTICLE

Dynamic milling force model for a milling cutter under vibration

Authors: Bin Jiang, Tingzheng Zhang, Peiyi Zhao, Junfeng Zhao

Published in: The International Journal of Advanced Manufacturing Technology | Issue 5-6/2020

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

Dynamic milling force under milling vibration is an important indicator for evaluating the milling stability of a milling cutter. The existing modeling methods for milling force ignore the milling vibration for the instantaneous milling behavior of a milling cutter and its teeth, the instantaneous cutter-workpiece engagement, and the milling force. The dynamic characteristics of the milling force need to be revealed. According to the influence characteristics of milling vibration on instantaneous cutter-workpiece engagement, a method for calculating the instantaneous milling attitude angle and the milling motion trajectory of a milling cutter and its cutter teeth was proposed that revealed the changing characteristics of the instantaneous milling behavior of the cutter teeth. The differential element method was used to characterize the distribution state of the milling force of a cutter tooth. The method for calculating the cutting layer thickness of the milling differential element and the instantaneous cutting boundary of the milling edge was put forward, and the instantaneous milling force model of the milling edge was established. By constructing an instantaneous milling force system for multi-tooth milling, a method for calculating the position vector relation variable and the force vector relation variable of the instantaneous milling force of adjacent cutter teeth was proposed, thus revealing the dynamic characteristics of the instantaneous milling force relationship of the adjacent cutter teeth. The dynamic characteristics and the response characteristics of the milling force were tested. The results showed that the calculated results of the dynamic milling force change characteristics of the milling cutter were quite similar to the experimental results. The influence mechanisms of milling vibration, cutter structure parameters, and milling parameters on the dynamic milling force of a milling cutter can be identified with the use of the above models and methods.

previous article A high-precision laser method for directly and quickly measuring 21 geometric motion errors of three linear axes of computer numerical control machine tools

next article Mechanical and thermal effects of abrasive cut-off applied in low and medium carbon steels using aluminum oxide cutting disc

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

Totis G, Albertelli P, Tortac M, Sortinoa M, Monnob M (2017) Upgraded stability analysis of milling operations by means of advanced modeling of tooling system bending. Int J Mach Tool Manu 113:19–34CrossRef

Zhang HT, Wu Y, He DF, Zhao H (2015) Model predictive control to mitigate chatters in milling processes with input constraints. Int J Mach Tool Manu 91:54–61CrossRef

Li AH, Zhao J, Luo HB, Pei ZQ, Wang ZM (2012) Progressive tool failure in high-speed dry milling of Ti-6Al-4 V alloy with coated carbide tools. Int J Adv Manuf Technol 58:465–478CrossRef

Chen WQ, Huo DH, Hale J, Ding H (2018) Kinematics and tool-workpiece separation analysis of vibration assisted milling. Int J Mech Sci 136:169–178CrossRef

Jiang B, Zhang MH, Yao GS, Bai JX (2016) Trans-scale design method on safety of high speed milling cutter. Chin J Mech Eng-En 52(5):202–206CrossRef

Yao XF, Zhang Y, Li B, Zhang Z, Shen XQ (2013) Machining force control with intelligent compensation. Int J Adv Manuf Technol 69:1701–1715CrossRef

Huang PL, Li JF, Sun J, Ge MJ (2012) Milling force vibration analysis in high-speed-milling titanium alloy using variable pitch angle mill. Int J Adv Manuf Technol 58(1-4):153–160CrossRef

Zhang XM, Ding H (2013) Note on a novel method for machining parameters optimization in a chatter-free milling process. Int J Mach Tool Manu 72(Complete):11–15CrossRef

Singh KK, Kartik V, Singh R (2015) Modeling dynamic stability in high-speed micromilling of Ti-6Al-4 V via velocity and chip load dependent cutting coefficients. Int J Mach Tool Manu 96:56–66CrossRef

10.

Andersson C, Andersson M, Ståhl JE (2011) Experimental studies of cutting force variation in face milling. Int J Mach Tool Manu 51(1):67–76CrossRef

11.

Ni CB, Zhu LD, Liu CF, Yang ZC (2018) Analytical modeling of tool-workpiece contact rate and experimental study in ultrasonic vibration-assisted milling of Ti–6Al–4 V. Int J Mech Sci 142-143:97–111CrossRef

12.

Liu JJ, Jiang XG, Gao Z, Zhang ML, Zhang DY (2018) Investigation of the effect of vibration amplitude on the surface integrity in high-speed rotary ultrasonic elliptical machining for side milling of Ti-6Al-4 V. Chin J Mech Eng-En 55(11):215–223CrossRef

13.

Kumar M, Dotson K, Melkote SN (2010) An experimental technique to detect tool–workpiece contact in micromilling. J Manuf Process 12(2):99–105CrossRef

14.

Boess V, Ammermann C, Niederwestberg D, Denkena B (2012) Contact zone analysis based on multidexel workpiece model and detailed tool geometry representation. Procedia CIRP 4:41–45CrossRef

15.

Rivière-Lorphèvre E, Letot C, Ducobu F, Dehombreux P, Filippi E (2017) Dynamic simulation of milling operations with small diameter milling cutters: ffect of material heterogeneity on the cutting force model. Meccanica 52(1-2):35–44CrossRef

16.

Filho SLMR, Pereira RBD, Lauro CH, Brandão LC (2019) Investigation and modelling of the cutting forces in turning process of the Ti-6Al-4 V and Ti-6Al-7Nb titanium alloys. Int J Adv Manuf Technol 101(9):2191–2203CrossRef

17.

Li KX, Zhu KP, Mei T (2016) A generic instantaneous undeformed chip thickness model for the cutting force modeling in micromilling. Int J Mach Tool Manu 105:23–31CrossRef

18.

Zhang X, Zhang J, Pang B, Zhao WH (2016) An accurate prediction method of cutting forces in 5-axis flank milling of sculptured surface. Int J Mach Tool Manu 104:26–36CrossRef

19.

Nie Q, Huang K, Bi QZ, Zhu LM (2016) New mathematic method of calculating instantaneous un-deformed chip thickness with tool run-out in micro-end-milling. Chin J Mech Eng-En 52(3):169–178CrossRef

20.

Luo ZW, Zhao WX, Jiao L, Gao SF, Liu ZB, Yan P, Wang XB (2016) Cutting force modeling in end milling of curved geometries based on oblique cutting process. Chin J Mech Eng-En 52(9):184–192CrossRef

21.

Du JG, Li JG, Yao YX, Hao ZP (2014) Prediction of cutting forces in mill-grinding SiCp/Al composites. Mater Manuf Process 29(3):314–320CrossRef

22.

Jiang B, Xu T, Li Z, Gu YP, He TT (2018) Characterisation for differential wear between left and right flank faces in turning large pitch internal thread. International Journal of Mechatronics and Manufacturing Systems 11:325–347CrossRef

Title: Dynamic milling force model for a milling cutter under vibration
Authors: Bin Jiang
Tingzheng Zhang
Peiyi Zhao
Junfeng Zhao
Publication date: 14-07-2020
Publisher: Springer London
Published in: The International Journal of Advanced Manufacturing Technology / Issue 5-6/2020
Print ISSN: 0268-3768
Electronic ISSN: 1433-3015
DOI: https://doi.org/10.1007/s00170-020-05635-w

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 5-6/2020

Fiber reinforced composite manufacturing for passive actuators

Experimental analysis of single layer multi-track deposition of clad beads with variable overlap percentages

Process planning of automatic wire arc additive remanufacturing for hot forging die

The fatigue performance of titanium alloys joined via the powder interlayer bonding method

Mitigation of the Microsoft HoloLens’ hardware limitations for a controlled product assembly process

Predictive modelling and parametric optimization of minimum quantity lubrication–assisted hobbing process

Premium Partners