Top

The International Journal of Advanced Manufacturing Technology

Published in:

15-03-2024 | ORIGINAL ARTICLE

Eco-friendly machining of advanced ceramics: wheel cleaning jet for greenhouse gas reduction

Authors: Douglas Lyra de Moraes, Andrigo Elisiario da Silva, Lucas Marcel Aparecido Costa Pilati, Anthony Gaspar Talon, Fernando Sabino Fonteque Ribeiro, Luiz Eduardo de Angelo Sanchez, Eduardo Carlos Bianchi, José Claudio Lopes

Published in: The International Journal of Advanced Manufacturing Technology | Issue 1-2/2024

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

The constant development of new materials, such as ceramics with high wear resistance, makes it necessary to adapt machining processes by creating new methods or improving existing ones. Moreover, grinding is widely used as a finishing process in workpieces since it provides excellent surface roughness and dimensional tolerances. Due to the high volume of cutting fluid used in conventional lubrication (flood), associated with harmful effects such as contamination and intoxication, alternative methods have become highly necessary. The minimum quantity lubrication (MQL) technique reduces fluid use but has low cooling capacity, in addition to barely removing chips, making it essential to seek improvements to make it competitive. In this sense, adding water to the MQL can improve the cooling capacity at the cost of reducing lubrication. At the same time, applying a wheel cleaning jet (WCJ) of compressed air assists in chip removal. Thus, this work aims to analyze the results of external cylindrical grinding of alumina (Al₂O₃) using a synthetic diamond grinding wheel, comparing the techniques of conventional MQL, diluted MQL, and MQL + WCJ against the flood method. Surface roughness, roundness deviation, diametrical wheel wear, G ratio, grinding power, tangential cutting force, grinding cost analyses, and CO₂ pollution emission were conducted for this. The results show that adding water to MQL, associated with WCJ, significantly improved roughness, wear, and grinding power. Furthermore, the analysis of costs and pollution showed that using MQL significantly reduced costs and CO₂ emissions, proving the socio-environmental advantage of the MQL method against the flood method.

previous article Effects of welding parameters and thermal insulation on the mechanical behavior and microstructure of friction lap-welded aluminum to glass fiber–reinforced thermoset composite with a thermoplastic PA6 interlayer

next article Cutting stress modeling and parameter identification for fine drilling process based on various cutting mechanisms

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

Malkin S, Guo C (2008) Grinding technology: theory and applications of machining with abrasives, 2nd edn. Industrial Press Inc, New York

Klocke F (2009) Manufacturing processes 2: grinding, honing, lapping, 1st edn. Springer-Verlag, Berlin HeidelbergCrossRef

Marinescu ID, Doi TK, Eckart U (2015) Handbook of ceramics grinding and polishing, 2nd edn. Elsevier

Khoshaim AB, Xu Z, D Marinescu I (2015) ELID grinding with lapping kinematics. Handbook of ceramics grinding and polishing 394–448. https://doi.org/10.1016/B978-1-4557-7858-4.00011-X

Marinescu ID, Hitchiner M, Uhlmann E, Rowe WB (2007) Handbook of machining with grinding wheels, 1st edn. CRC Press, New York

Sato BK, Lopes JC, Diniz AE et al (2020) Toward sustainable grinding using minimum quantity lubrication technique with diluted oil and simultaneous wheel cleaning. Tribol Int 147:106276. https://doi.org/10.1016/j.triboint.2020.106276CrossRef

Rodriguez RL, Lopes JC, Garcia MV et al (2020) Application of hybrid eco-friendly MQL+WCJ technique in AISI 4340 steel grinding for cleaner and greener production. J Clean Prod 124670. https://doi.org/10.1016/j.jclepro.2020.124670

Garcia MV, Lopes JC, Diniz AE et al (2020) Grinding performance of bearing steel using MQL under different dilutions and wheel cleaning for green manufacture. J Clean Prod 257:120376. https://doi.org/10.1016/j.jclepro.2020.120376CrossRef

Rodriguez RL, Lopes JC, Garcia MV et al (2020) Grinding process applied to workpieces with different geometries interrupted using CBN wheel. Int J Adv Manuf Technol 107:1265–1275. https://doi.org/10.1007/s00170-020-05122-2CrossRef

10.

Li Y, Liu Y, Tian Y et al (2022) Application of improved fireworks algorithm in grinding surface roughness online monitoring. J Manuf Process 74:400–412. https://doi.org/10.1016/j.jmapro.2021.12.046CrossRef

11.

Sarikaya M, Gupta MK, Tomaz I et al (2021) Cooling techniques to improve the machinability and sustainability of light-weight alloys: a state-of-the-art review. J Manuf Process 62:179–201. https://doi.org/10.1016/j.jmapro.2020.12.013CrossRef

12.

Javaroni RL, Lopes JC, Diniz AE et al (2020) Improvement in the grinding process using the MQL technique with cooled wheel cleaning jet. Tribol Int 152:106512. https://doi.org/10.1016/j.triboint.2020.106512CrossRef

13.

Zhang Y, Li C, Jia D et al (2015) Experimental evaluation of MoS2 nanoparticles in jet MQL grinding with different types of vegetable oil as base oil. J Clean Prod 87:930–940. https://doi.org/10.1016/j.jclepro.2014.10.027CrossRef

14.

Malkin S, Bitter JE (1989) Grinding mechanisms and strength degradation for ceramics. J Manuf Sci E T ASME 111:167–174. https://doi.org/10.1115/1.3188746CrossRef

15.

Malkin S, Guo C (2007) Thermal analysis of grinding. CIRP Ann Manuf Technol 56:760–782. https://doi.org/10.1016/j.cirp.2007.10.005CrossRef

16.

Lakhdar Y, Tuck C, Binner J et al (2021) Additive manufacturing of advanced ceramic materials. Prog Mater Sci 116:100736. https://doi.org/10.1016/j.pmatsci.2020.100736CrossRef

17.

Javaroni RL, Lopes JC, Sato BK et al (2019) Minimum quantity of lubrication (MQL) as an eco-friendly alternative to the cutting fluids in advanced ceramics grinding. Int J Adv Manuf Technol 103:2809–2819. https://doi.org/10.1007/s00170-019-03697-zCrossRef

18.

King RI, Hahn RS, Devereux OF (2009) Handbook of modern grinding technology. J Eng Mater Technol doi 10(1115/1):3225989

19.

Bhuiyan MSH, Choudhury IA, Dahari M et al (2016) Application of acoustic emission sensor to investigate the frequency of tool wear and plastic deformation in tool condition monitoring. Measurement (Lond) 92:208–217. https://doi.org/10.1016/j.measurement.2016.06.006CrossRef

20.

Denkena B, Grove T, Göttsching T (2015) Grinding with patterned grinding wheels. CIRP J Manuf Sci Technol 8:12–21. https://doi.org/10.1016/J.CIRPJ.2014.10.005CrossRef

21.

Talon AG, Lopes JC, Tavares AB et al (2019) Effect of hardened steel grinding using aluminum oxide wheel under application of cutting fluid with corrosion inhibitors. Int J Adv Manuf Technol 104:1437–1448. https://doi.org/10.1007/s00170-019-04005-5CrossRef

22.

Talon AG, Lopes JC, Sato BK et al (2020) Grinding performance of hardened steel: a study about the application of different cutting fluids with corrosion inhibitor. Int J Adv Manuf Technol 108:2741–2754. https://doi.org/10.1007/s00170-020-05598-yCrossRef

23.

Javaroni RL, Lopes JC, Ribeiro FSF et al (2020) Evaluation of a cooled wheel cleaning jet in minimum quantity lubrication grinding process. Int J Adv Manuf Technol 111:1303–1317. https://doi.org/10.1007/s00170-020-06198-6CrossRef

24.

Lopes JC, Martini Fernandes L, Garcia MV et al (2020) Performance of austempered ductile iron (ADI) grinding using diluted oil in MQL combined with wheel cleaning jet and different CBN grains friability. Int J Adv Manuf Technol 107:1805–1818. https://doi.org/10.1007/s00170-020-05142-yCrossRef

25.

Benedicto E, Carou D, Rubio EM (2017) Technical, economic and environmental review of the lubrication/cooling systems used in machining processes. Procedia Eng 184:99–116. https://doi.org/10.1016/j.proeng.2017.04.075CrossRef

26.

Kalpakjian S, Schmid SR (2018) Manufacturing engineering and technology. Prientice Hall, New Jersey

27.

Siniawski M, Bowman C (2009) Metal working fluids: finding green in the manufacturing process. Ind Lubr Tribol 61:60–66. https://doi.org/10.1108/00368790910940374CrossRef

28.

Pušavec F, Stoić A, Kopač J (2010) Sustainable machining process - myth or reality. Strojarstvo 52:197–204

29.

Shokrani A, Dhokia V, Newman ST (2012) Environmentally conscious machining of difficult-to-machine materials with regard to cutting fluids. Int J Mach Tools Manuf 57:83–101. https://doi.org/10.1016/j.ijmachtools.2012.02.002CrossRef

30.

Bui M, Adjiman CS, Bardow A et al (2018) Carbon capture and storage (CCS): the way forward. Energy Environ Sci 11:1062–1176. https://doi.org/10.1039/C7EE02342ACrossRef

31.

Lopes JC, Ávila BN, de Souza RM et al (2021) Grinding comparative analysis between different proportions of water-oil applied to MQL technique and industrial production cost towards a green manufacturing. Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-021-06625-2CrossRef

32.

da Silva LR, Bianchi EC, Fusse RY et al (2007) Analysis of surface integrity for minimum quantity lubricant-MQL in grinding. Int J Mach Tools Manuf 47:412–418. https://doi.org/10.1016/j.ijmachtools.2006.03.015CrossRef

33.

Hadad M (2015) An experimental investigation of the effects of machining parameters on environmentally friendly grinding process. J Clean Prod 108:217–231. https://doi.org/10.1016/j.jclepro.2015.05.092CrossRef

34.

Hadad M, Sharbati A (2016) Thermal aspects of environmentally friendly-MQL grinding process. Procedia CIRP 40:509–515. https://doi.org/10.1016/j.procir.2016.01.125CrossRef

35.

Wang Y, Li C, Zhang Y et al (2016) Experimental evaluation of the lubrication properties of the wheel/workpiece interface in minimum quantity lubrication (MQL) grinding using different types of vegetable oils. J Clean Prod 127:487–499. https://doi.org/10.1016/j.jclepro.2016.03.121CrossRef

36.

Sato BK, Lopes JC, Rodriguez RL et al (2021) Eco-friendly manufacturing towards the industry of the future with a focus on less cutting fluid and high workpiece quality applied to the grinding process. Int J Adv Manuf Technol 113:1163–1172. https://doi.org/10.1007/s00170-021-06650-1CrossRef

37.

Abbas AT, Gupta MK, Soliman MS et al (2019) Sustainability assessment associated with surface roughness and power consumption characteristics in nanofluid MQL-assisted turning of AISI 1045 steel. Int J Adv Manuf Technol 105:1311–1327. https://doi.org/10.1007/s00170-019-04325-6CrossRef

38.

Heinzel C, Antsupov G (2012) Prevention of wheel clogging in creep feed grinding by efficient tool cleaning. CIRP Ann Manuf Technol 61:323–326. https://doi.org/10.1016/j.cirp.2012.03.056CrossRef

39.

Rodriguez RL, Lopes JC, Hildebrandt RA et al (2019) Evaluation of grinding process using simultaneously MQL technique and cleaning jet on grinding wheel surface. J Mater Process Technol 271:357–367. https://doi.org/10.1016/j.jmatprotec.2019.03.019CrossRef

40.

Lopes JC, de Martini FL, Domingues BB et al (2019) Effect of CBN grain friability in hardened steel plunge grinding. Int J Adv Manuf Technol 103:1567–1577. https://doi.org/10.1007/s00170-019-03654-wCrossRef

41.

Lopes JC, Ribeiro FSF, Linkevicius SAS et al (2022) Manufacturing process linked to the MQL compared to flood lubrication applied to the grinding of VP50IM steel using black silicon carbide wheel. Int J Adv Manuf Technol 120:4179–4190. https://doi.org/10.1007/s00170-022-08937-3CrossRef

42.

Sato BK, Lopes JC, Rodriguez RL et al (2022) Novel comparison concept between CBN and Al2O3 grinding process for eco-friendly production. J Clean Prod 330:129673. https://doi.org/10.1016/j.jclepro.2021.129673CrossRef

43.

Sharma A, Khan Yusufzai MZ, Vashista M (2022) A comparative analysis of grinding of AISI D2 tool steel under different environments. 26:183–202. https://doi.org/10.1080/10910344.2022.2044853

44.

Gajrani KK, Prasad A, Kumar A (2022) Advances in sustainable machining and manufacturing processes. CRC PressCrossRef

45.

Bruzzone AAG, Costa HL, Lonardo PM, Lucca DA (2008) Advances in engineered surfaces for functional performance. CIRP Ann Manuf Technol 57:750–769. https://doi.org/10.1016/j.cirp.2008.09.003CrossRef

46.

de Souza RR, de Moraes DL, Garcia MV et al (2021) Effect of grinding with different CBN grains applied to austempered ductile iron linked to quality and industrial cost. Int J Adv Manuf Technol 113:807–820. https://doi.org/10.1007/s00170-021-06647-wCrossRef

47.

Jayal AD, Badurdeen F, Dillon OW, Jawahir IS (2010) Sustainable manufacturing: modeling and optimization challenges at the product, process and system levels. CIRP J Manuf Sci Technol 2:144–152. https://doi.org/10.1016/j.cirpj.2010.03.006CrossRef

48.

Debnath S, Reddy MM, Yi QS (2014) Environmental friendly cutting fluids and cooling techniques in machining: a review. J Clean Prod 83:33–47. https://doi.org/10.1016/j.jclepro.2014.07.071CrossRef

49.

Lee J, Lapira E, Bagheri B, Kao H-a (2013) Recent advances and trends in predictive manufacturing systems in big data environment. Manuf Lett 1:38–41. https://doi.org/10.1016/j.mfglet.2013.09.005CrossRef

50.

Field M, Kegg R, Buescher S (1980) Computerized cost analysis of grinding operations. CIRP Ann 29:233–237. https://doi.org/10.1016/S0007-8506(07)61328-6CrossRef

51.

Hitchcox A (2015) Determine the cost of compressed air for your plant. https://www.hydraulicspneumatics.com/technologies/air-compressors/article/21884932/determine-the-cost-of-compressed-air-for-your-plant. Accessed 18 Oct 2023

52.

(2020) Electricity prices. https://www.globalpetrolprices.com/electricity_prices/. Accessed 16 Nov 2020

53.

Abellan-Nebot JV, Rogero MO (2019) Sustainable machining of molds for tile industry by minimum quantity lubrication. J Clean Prod 240:118082. https://doi.org/10.1016/j.jclepro.2019.118082CrossRef

54.

Pusavec F, Kramar D, Krajnik P, Kopac J (2010) Transitioning to sustainable production – part II: evaluation of sustainable machining technologies. J Clean Prod 18:1211–1221. https://doi.org/10.1016/j.jclepro.2010.01.015CrossRef

55.

Demirbas E, Kobya M (2017) Operating cost and treatment of metalworking fluid wastewater by chemical coagulation and electrocoagulation processes. Process Saf Environ Prot 105:79–90. https://doi.org/10.1016/j.psep.2016.10.013CrossRef

56.

Wang Z, Zhang T, Yu T, Zhao J (2020) Assessment and optimization of grinding process on AISI 1045 steel in terms of green manufacturing using orthogonal experimental design and grey relational analysis. J Clean Prod 253:119896. https://doi.org/10.1016/j.jclepro.2019.119896CrossRef

57.

Lopes JC, Carvalho GA de, Moretti GB et al (2023) Sustainable thinking toward to industry’s future combined with new knowledge on greenhouse effect mitigation generated by the grinding process. J Clean Prod 386. https://doi.org/10.1016/j.jclepro.2022.135810

58.

Daniel DM, de Moraes DL, Garcia MV et al (2023) Application of MQL with cooled air and wheel cleaning jet for greener grinding process. Int J Adv Manuf Technol 125:435–452. https://doi.org/10.1007/s00170-022-10712-3CrossRef

59.

Rowe WB (2014) Principles of modern grinding technology, 2nd edn. William Andrew, United States

60.

Zhang Q, Zhao Q, To S et al (2017) Diamond wheel wear mechanism and its impact on the surface generation in parallel diamond grinding of RB-SiC/Si. Diam Relat Mater 74:16–23. https://doi.org/10.1016/J.DIAMOND.2017.01.019CrossRef

61.

de Martini Fernandes L, Javaroni RL, de Souza Rodrigues M et al (2023) Advanced ceramic grinding process combined to hazard mitigation to the employees’ health by using an alternative lubri-refrigeration technique. Int J Adv Manuf Technol 127:2921–2934. https://doi.org/10.1007/s00170-023-11674-wCrossRef

62.

de Jesus Oliveira D, Guermandi LG, Bianchi EC et al (2012) Improving minimum quantity lubrication in CBN grinding using compressed air wheel cleaning. J Mater Process Technol 212:2559–2568. https://doi.org/10.1016/j.jmatprotec.2012.05.019CrossRef

63.

Novoselov Yu, Bratan S, Bogutsky V (2016) Analysis of relation between grinding wheel wear and abrasive grains wear. Procedia Eng 150:809–814. https://doi.org/10.1016/j.proeng.2016.07.116CrossRef

64.

Li W, Winter M, Kara S, Herrmann C (2012) Eco-efficiency of manufacturing processes: a grinding case. CIRP Ann Manuf Technol 61:59–62. https://doi.org/10.1016/j.cirp.2012.03.029CrossRef

65.

Winter M, Li W, Kara S, Herrmann C (2014) Determining optimal process parameters to increase the eco-efficiency of grinding processes. J Clean Prod 66:644–654. https://doi.org/10.1016/j.jclepro.2013.10.031CrossRef

66.

Lopes JC, Fragoso KM, Garcia MV et al (2019) Behavior of hardened steel grinding using MQL under cold air and MQL CBN wheel cleaning. Int J Adv Manuf Technol 105:4373–4387. https://doi.org/10.1007/s00170-019-04571-8CrossRef

67.

Duflou JR, Sutherland JW, Dornfeld D et al (2012) Towards energy and resource efficient manufacturing: a processes and systems approach. CIRP Ann Manuf Technol 61:587–609. https://doi.org/10.1016/j.cirp.2012.05.002CrossRef

68.

Moretti GB, Ávila BN, Lopes JC et al (2021) Industrial manufacturing linked to the mechanical and economic viewpoint of the mold steel grinding process using aluminum oxide wheel. Int J Adv Manuf Technol 117:2655–2666. https://doi.org/10.1007/s00170-021-07827-4CrossRef

Title: Eco-friendly machining of advanced ceramics: wheel cleaning jet for greenhouse gas reduction
Authors: Douglas Lyra de Moraes
Andrigo Elisiario da Silva
Lucas Marcel Aparecido Costa Pilati
Anthony Gaspar Talon
Fernando Sabino Fonteque Ribeiro
Luiz Eduardo de Angelo Sanchez
Eduardo Carlos Bianchi
José Claudio Lopes
Publication date: 15-03-2024
Publisher: Springer London
Published in: The International Journal of Advanced Manufacturing Technology / Issue 1-2/2024
Print ISSN: 0268-3768
Electronic ISSN: 1433-3015
DOI: https://doi.org/10.1007/s00170-024-13433-x

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 1-2/2024

Principle and effectiveness of ice fixation clamping in the milling of GH4099 superalloy honeycomb core

Research on geometric error compensation of ultra-precision turning-milling machine tool based on macro–micro composite technology

Analysis of mesostructural characteristics and their influence on tensile strength of ABS specimens manufactured through fused deposition modeling

A novel numerical modeling of microsecond laser beam percussion micro-drilling of Hastelloy X: experimental validation and multi-objective optimization

Prediction and analysis of grinding force on grinding heads based on grain measurement statistics and single-grain grinding simulation

Concentricity control for multistage rotor assembly based on contour vectorization

Premium Partners