Top

Published in:

2021 | OriginalPaper | Chapter

Erosion of Titanium and Aluminium Alloys Using Pulsating Water Jet: Effect of Standoff Distance

Authors : Dominik Čuha, Akash Nag, Alice Chlupová, Sergej Hloch

Published in: Advances in Water Jetting

Publisher: Springer International Publishing

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

The disintegration of the material by PWJ technology depends upon many technological parameters of the equipment and particular material properties. This paper deals with the erosive effects of PWJ on the polished surfaces of metallic materials such as titanium (Ti6Al4V) and aluminium (ENAW1050AH24) alloy. The evaluation and comparison of the extent of disintegration are done on the basis of the erosion depth achieved. The nozzle movement over the material followed an ascending equidistant trajectory from z = 15 to 41 mm with a vertical step height of 2 mm. PWJ transitions over the material were performed with a sonotrode frequency f = 20.19 kHz, liquid pressure p = 40 MPa and a feed rate v = 0.25 mm.s⁻¹. The depth value of the grooves formed was then measured using a MicroProf FRT contactless measuring device and evaluated in the SPIP 6.7.8 software. For aluminium sample, the deepest average depth value is h = 1583.2 µm (z = 29 mm), while the titanium material has eroded to a much smaller depth, h = 283.2 µm (z = 31 mm). By comparing the achieved hydrodynamic effects of PWJ on titanium and aluminium, significant differences in the depth of erosion and its course can be observed due to the different mechanical properties of the materials.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

previous chapter Effect of Abrasive Water Jet Machining on the Geometry of Shapes in Selected Tool Steels

next chapter Water Jet as a Promising Tool to Disperse Carbon Nanotubes in Water Solution

Hloch, S., Nag, A., Pude, F., Foldyna, J., Zeleňák, M.: On-line measurement and monitoring of pulsating saline and water jet disintegration of bone cement with frequency 20 kHz. Measurement 147, 106828 (2019). https://doi.org/10.1016/j.measurement.2019.07.056CrossRef

Lehocká, D., Klich, J., Botko, F., Foldyna, J., Hloch, S., Kepič, J., Kovaľ, K., Krejči, L., Storkan, Z.: Pulsating water jet erosion effect on a brass flat solid surface. Int. J. Adv. Manuf. Technol. 97, 1099–1112 (2018). https://doi.org/10.1007/s00170-018-1882-4CrossRef

Raj, P., Hloch, S., Tripathi, R., Srivastava, M., Nag, A., Klichová, D., Klich, J., Hromasová, M., Muller, M., Miloslav, L., Chattopadhyaya, S., Adamcik, P.: Investigation of sandstone erosion by continuous and pulsed water jets. J. Manuf. Process. 42, 121–130 (2019). https://doi.org/10.1016/j.jmapro.2019.04.035CrossRef

Nag, A., Srivastava, A.K., Dixit, A.R., Chattopadhyaya, S., Mandal, A., Klichová, D., Hlaváček, P., Zeleňák, M., Hloch, S.: Influence of abrasive water jet turning parameters on variation of diameter of hybrid metal matrix composite. In: Singh, M., Kushvah, B., Seth, G., Prakash, J. (eds.) Applications of Fluid Dynamics, pp. 495–504. Springer, Singapore (2018)CrossRef

Hloch, S., Hlaváček, J., Vasilko, K., Cárach, J., Samardžić, I., Kozak, D., Hlavatý, I., Ščučka, J.J., Klich, J., Klichová, D.: Abrasive waterjet (AWJ) titanium tangential turning evaluation. Metalurgija 53, 537–540 (2014)

Hlaváček, P., Cárach, J., Hloch, S., Vasilko, K., Klichová, D., Klich, J., Lehocká, D.: Sandstone turning by abrasive waterjet. Rock Mech. Rock Eng. 48, 2489–2493 (2015). https://doi.org/10.1007/s00603-015-0719-9CrossRef

Cárach, J., Hloch, S., Hlaváček, P., Ščučka, J., Martinec, P., Petrů, J., Zlámal, T., Zeleňák, M., Monka, P., Lehocká, D.: Tangential turning of Incoloy alloy 925 using abrasive water jet technology. Int. J. Adv. Manuf. Technol. 82, 1747–1752 (2016). https://doi.org/10.1007/s00170-015-7489-0CrossRef

Hutyrová, Z., Ščučka, J., Hloch, S., Hlaváček, P., Zeleňák, M.: Turning of wood plastic composites by water jet and abrasive water jet. Int. J. Adv. Manuf. Technol. 84, 1615–1623 (2016). https://doi.org/10.1007/s00170-015-7831-6CrossRef

Cárach, J., Hloch, S., Petrů, J., Nag, A., Gombár, M., Hromasová, M.: Hydroabrasive disintegration of rotating Monel K-500 workpiece. Int. J. Adv. Manuf. Technol. 96, 981–1001 (2018). https://doi.org/10.1007/s00170-018-1653-2CrossRef

10.

Srivastava, A.K., Nag, A., Dixit, A.R., Tiwari, S., Scucka, J., Zelenak, M., Hloch, S., Hlavacek, P.: Surface integrity in tangential turning of hybrid MMC A359/B4C/Al2O3by abrasive waterjet. J. Manuf. Process. 28, 11–20 (2017). https://doi.org/10.1016/j.jmapro.2017.05.017CrossRef

11.

Nag, A., Ščučka, J., Hlavacek, P., Klichová, D., Srivastava, A.K., Hloch, S., Dixit, A.R., Foldyna, J., Zelenak, M.: Hybrid aluminium matrix composite AWJ turning using olivine and Barton garnet. Int. J. Adv. Manuf. Technol. 94, 2293–2300 (2018). https://doi.org/10.1007/s00170-017-1036-0CrossRef

12.

Srivastava, M., Tripathi, R., Hloch, S., Chattopadhyaya, S., Dixit, A.R.: Potential of using water jet peening as a surface treatment process for welded joints. Procedia Eng. 149, 472–480 (2016). https://doi.org/10.1016/j.proeng.2016.06.694CrossRef

13.

Srivastava, M., Hloch, S., Gubeljak, N., Milkovic, M., Chattopadhyaya, S., Klich, J.: Surface integrity and residual stress analysis of pulsed water jet peened stainless steel surfaces. Measurement 143, 81–92 (2019). https://doi.org/10.1016/j.measurement.2019.04.082CrossRef

14.

Hloch, S., Srivastava, M., Krolczyk, J.B., Chattopadhyaya, S., Lehocká, D., Simkulet, V., Krolczyk, G.M.: Strengthening effect after disintegration of stainless steel using pulsating water jet. Teh. Vjesn. 25, 1075–1079 (2018). https://doi.org/10.17559/TV-20170327134630CrossRef

15.

Foldyna, J., Sitek, L., Švehla, B., Švehla, S.: Utilization of ultrasound to enhance high-speed water jet effects. Ultrason. Sonochem. 11 (2004). https://doi.org/10.1016/j.ultsonch.2004.01.008

16.

Chillman, A., Ramulu, M., Hashish, M.: A general overview of waterjet surface treatment modeling. In: American WJTA Conference and Expo (2009)

17.

Srivastava, M., Hloch, S., Krejci, L., Chattopadhyaya, S., Dixit, A.R., Foldyna, J.: Residual stress and surface properties of stainless steel welded joints induced by ultrasonic pulsed water jet peening. Meas. J. Int. Meas. Confed. 127, 453–462 (2018). https://doi.org/10.1016/j.measurement.2018.06.012CrossRef

18.

Srivastava, M., Hloch, S., Tripathi, R., Kozak, D., Chattopadhyaya, S., Dixit, A.R., Foldyna, J., Hvizdos, P., Fides, M., Adamcik, P.: Ultrasonically generated pulsed water jet peening of austenitic stainless-steel surfaces. J. Manuf. Process. 32 (2018). https://doi.org/10.1016/j.jmapro.2018.03.016

19.

Hloch, S., Foldyna, J., Pude, F., Kľoc, J., Zeleňák, M., Hvizdoš, P., Monka, P., Smolko, I., Ščučka, J., Kozak, D.: Experimental in-vitro bone cements disintegration with ultrasonic pulsating water jet for revision arthroplasty. Tech. Gaz. 22, 1609–1615 (2015). https://doi.org/10.17559/TV-20150822145550CrossRef

20.

Hloch, S., Foldyna, J., Sitek, L., Zeleňák, M., Hlaváček, P., Hvizdoš, P., Kľoc, J., Monka, P., Monková, K., Kozak, D., Magurová, D.: Disintegration of bone cement by continuous and pulsating water jet. Tech. Gaz. 20, 593–598 (2013). https://hrcak.srce.hr/106686

21.

Nag, A., Hloch, S., Dixit, A.R., Cuha, D.: Investigation on pulsating liquid jet with physiological saline on aluminium surface. In: Hloch, S., Klichová, D., Krolczyk, G., Chattopadhyaya, S., Ruppenthalová, L. (eds.) Advances in Manufacturing Engineering and Materials, pp. 63–71. Springer, Cham (2019). https://doi.org/10.1007/978-3-319-99353-9_8CrossRef

22.

Nag, A., Hloch, S., Čuha, D., Dixit, A.R., Tozan, H., Petrů, J., Hromasová, M., Müller, M.: Acoustic chamber length performance analysis in ultrasonic pulsating water jet erosion of ductile material. J. Manuf. Process. 47, 347–356 (2019). https://doi.org/10.1016/j.jmapro.2019.10.008CrossRef

23.

Lehocka, D., Klich, J., Foldyna, J., Hloch, S., Krolczyk, J.B., Carach, J., Krolczyk, G.M.: Copper alloys disintegration using pulsating water jet. Measurement 82, 375–383 (2016). https://doi.org/10.1016/j.measurement.2016.01.014CrossRef

24.

Lehocká, D., Klichová, D., Foldyna, J., Hloch, S., Hvizdoš, P., Fides, M., Botko, F.: Comparison of the influence of acoustically enhanced pulsating water jet on selected surface integrity characteristics of CW004A copper and CW614N brass. Measurement 110, 230–238 (2017). https://doi.org/10.1016/j.measurement.2017.07.005CrossRef

25.

Foldyna, J., Sitek, L., Ščučka, J., Martinec, P., Valíček, J., Páleníková, K.: Effects of pulsating water jet impact on aluminium surface. J. Mater. Process. Technol. 209, 6174–6180 (2009). https://doi.org/10.1016/j.jmatprotec.2009.06.004CrossRef

26.

Hloch, S., Adamčík, P., Nag, A., Srivastava, M., Čuha, D., Müller, M., Hromasová, M., Klich, J.: Hydrodynamic ductile erosion of aluminium by a pulsed water jet moving in an inclined trajectory. Wear 428–429, 178–192 (2019). https://doi.org/10.1016/j.wear.2019.03.015CrossRef

27.

Lehocka, D., Klich, J., Botko, F., Simkulet, V., Foldyna, J., Krejci, L., Storkan, Z., Kepic, J., Hatala, M.: Comparison of ultrasonically enhanced pulsating water jet erosion efficiency on mechanical surface treatment on the surface of aluminum alloy and stainless steel. Int. J. Adv. Manuf. Technol., 1–10 (2019). https://doi.org/10.1007/s00170-019-03680-8

28.

Klich, J., Klichova, D., Foldyna, V., Hlavacek, P., Foldyna, J.: Influence of variously modified surface of aluminium alloy on the effect of pulsating water jet. Stroj. Vestn./J. Mech. Eng. 63, 577–582 (2017). https://doi.org/10.5545/sv-jme.2017.4356CrossRef

29.

Lehocka, D., Klich, J., Pitel, J., Krejci, L., Storkan, Z., Duplakova, D., Schindlerova, V., Sajdlerova, I.: Analysis of the pulsating water jet maximum erosive effect on stainless steel. In: Hloch, S., Klichová, D., Krolczyk, G., Chattopadhyaya, S., Ruppenthalová, L. (eds.) Advances in Manufacturing II, pp. 233–241. Springer, Cham (2019). https://doi.org/10.1007/978-3-030-16943-5_2CrossRef

30.

Foldyna, J., Klich, J., Hlavacek, P., Zelenak, M., Scucka, J.: Erosion of metals by pulsating water jet. Tech. Gaz. 19, 381–386 (2012). https://hrcak.srce.hr/83919

31.

Thomas, G.P., Brunton, J.H.: Drop impingement erosion of metals. Proc. R. Soc. A Math. Phys. Eng. Sci. (1970). https://doi.org/10.1098/rspa.1970.0022

Title: Erosion of Titanium and Aluminium Alloys Using Pulsating Water Jet: Effect of Standoff Distance
Authors: Dominik Čuha
Akash Nag
Alice Chlupová
Sergej Hloch
Publisher: Springer International Publishing
Book: Advances in Water Jetting
Print ISBN: 978-3-030-53490-5

Electronic ISBN: 978-3-030-53491-2

Copyright Year: 2021
DOI: https://doi.org/10.1007/978-3-030-53491-2_6

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Premium Partners