Top

Published in:

2019 | OriginalPaper | Chapter

58. Evaluation of Mechanical Properties of Ti6Al4V Built by Composite Coating of WS₂, CNT, Ni, and Ti6Al4V Powders Through Laser Cladding Process

Authors : Shakti Kumar, Umar Arif, Vikas Kumar, M. Anand, R. Tyagi, Amitava Mandal, A. K. Das

Published in: Advances in Micro and Nano Manufacturing and Surface Engineering

Publisher: Springer Singapore

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

Titanium and its alloy have wide application in the field of aerospace and marine engineering. But due to it’s poor tribological and weight to strength ratio make difficult to use in the critical working environment. To overcome this drawback a composite cladding of WS2, CNT, and Ni was formed on the Ti6Al4V substrate. In the present work select the process parameter at constant scanning speed (450 mm/min), laser power (125–250 W). The variations of layer thickness microhardness with respect to the input parameter have been analyzed and it was observed that laser power is the influential parameter to the output measure. Hence the maximum microhardness was found to be 1246 HV_.5 kg which is approximately three times more than that of the substrate material. Further characterization has been done for the morphological analysis which shows that strong bonding have been formed to the interface zone and there is no crack found but at a higher percentage of CNT some microcrack are observed. With the increase in WS2, wear resistance have been improved significantly in comparison to the substrate. XRD analysis observed that there are a number of a compounds like W₂C, WS₂, TiC, Ti₂S, NiS₂, and Al₄C₃ was formed which improve the mechanical properties of the substrate titanium alloy.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

previous chapter Laser Beam Treatment of Nimonic C263 Alloy: Study of Mechanical and Metallurgical Properties

next chapter Towards Extending ECAP Technology from Lab Scale to Manufacturing by Enhanced Multipass Continuous ECAP Process

Hussain, M., Kumar, V., Mandal, V., Singh, P.K., Kumar, P., Das, A.K.: Development of cBN reinforced Ti6Al4V MMCs through laser sintering and process optimization. Mater. Manuf. Process. 1–11 (2017). https://doi.org/10.1080/10426914.2017.1303152CrossRef

Hussain, M., Mandal, V., Singh, P.K., Kumar, P., Kumar, V., Das, A.K.: Experimental study of microstructure, mechanical and tribological properties of cBN particulates SS316 alloy based MMCs fabricated by DMLS technique. J. Mech. Sci. Technol. 31(6), 2729–2737 (2017). https://doi.org/10.1007/s12206-017-0516-3CrossRef

Zhu, Y., Wang, W., Jia, X., Akasaka, T., Liao, S., Watari, F.: Deposition of TiC film on titanium for abrasion resistant implant material by ion-enhanced triode plasma CVD. Appl. Surf. Sci. 262, 156–158 (2012). https://doi.org/10.1016/j.apsusc.2012.03.152CrossRef

Costa, M.Y.P., Venditti, M.L.R., Cioffi, M.O.H., Voorwald, H.J.C., Guimarães, V.A., Ruas, R.: Fatigue behavior of PVD coated Ti–6Al–4V alloy. Int. J. Fatigue 33(6), 759–765 (2011). https://doi.org/10.1016/j.ijfatigue.2010.11.007CrossRef

Kumar, S., Mandal, A., Das, A.K., Dixit, A.R.: Parametric study and characterization of AlN-Ni-Ti6Al4V composite cladding on titanium alloy. Surf. Coat. Technol. (2018). https://doi.org/10.1016/j.surfcoat.2018.05.053CrossRef

Kundu, S., Hussain, M., Kumar, V., Kumar, S., Das, A.K.: Direct metal laser sintering of TiN reinforced Ti6Al4V alloy based metal matrix composite: fabrication and characterization. Int. J. Adv. Manuf. Technol. 1–12 (2018). https://doi.org/10.1007/s00170-018-2159-7CrossRef

Yoon, S., Kim, H.J., Lee, C.: Deposition behavior of bulk amorphous NiTiZrSiSn according to the kinetic and thermal energy levels in the kinetic spraying process. Surf. Coat. Technol. 200(20–21), 6022–6029 (2006). https://doi.org/10.1016/j.surfcoat.2005.09.022CrossRef

Huang, N., Yang, P., Leng, Y.X., Wang, J., Sun, H., Chen, J.Y., Wan, G.J.: Surface modification of biomaterials by plasma immersion ion implantation. Surf. Coat. Technol. 186(1–2), 218–226 (2004). https://doi.org/10.1016/j.surfcoat.2004.04.041CrossRef

Candel, J.J., Amigó, V., Ramos, J.A., Busquets, D.: Sliding wear resistance of TiCp reinforced titanium composite coating produced by laser cladding. Surf. Coat. Technol. 204(20), 3161–3166 (2010). https://doi.org/10.1016/j.surfcoat.2010.02.070CrossRef

10.

Kobryn, P.A., Semiatin, S.L.: Microstructure and texture evolution during solidification processing of Ti–6Al–4V. J. Mater. Process. Technol. 135(2–3), 330–339 (2003). https://doi.org/10.1016/S0924-0136(02)00865-8CrossRef

11.

Wu, X., Liang, J., Mei, J., Mitchell, C., Goodwin, P.S., Voice, W.: Microstructures of laser-deposited Ti–6Al–4V. Mater. Des. 25(2), 137–144 (2004). https://doi.org/10.1016/j.matdes.2003.09.009 CrossRef

12.

Feng, S.R., Tang, H.B., Zhang, S.Q., Wang, H.M.: Microstructure and wear resistance of laser clad TiB–TiC/TiNi–Ti2Ni intermetallic coating on titanium alloy. Trans. Nonferrous Metals Soc. China 22(7), 1667–1673 (2012). https://doi.org/10.1016/S1003-6326(11)61371-XCrossRef

13.

Pang, W., Man, H.C., Yue, T.M.: Laser surface coating of Mo–WC metal matrix composite on the Ti6Al4V alloy. Mater. Sci. Eng. A 390(1–2), 144–153 (2005). https://doi.org/10.1016/j.msea.2004.07.065CrossRef

14.

Tu, J.P., Yang, Y.Z., Wang, L.Y., Ma, X.C., Zhang, X.B.: Tribological properties of carbon-nanotube-reinforced copper composites. Tribol. Lett. 10(4), 225–228 (2001). https://doi.org/10.1023/A:1016662114589CrossRef

15.

Giraldo, L.F., López, B.L., Brostow, W.: Effect of the type of carbon nanotubes on tribological properties of polyamide 6. Polym. Eng. Sci. 49(5), 896–902 (2009). https://doi.org/10.1002/pen.21386CrossRef

16.

Wu, W.L.: Dissolution precipitation mechanism of TiC/Ti composite layer produced by laser cladding. Mater. Sci. Technol. 26(3), 367–370 (2010). https://doi.org/10.1179/174328408X395998CrossRef

17.

Yang, S., Liu, W., Zhong, M., Wang, Z.: TiC reinforced composite coating produced by powder feeding laser cladding. Mater. Lett. 58(24), 2958–2962 (2004). https://doi.org/10.1016/j.matlet.2004.03.051CrossRef

18.

Wu, X.: In situ formation by laser cladding of a TiC composite coating with a gradient distribution. Surf. Coat. Technol. 115(2–3), 111–115 (1999). https://doi.org/10.1016/S0257-8972(99)00045-6CrossRef

19.

Mandal, V., Hussain, M., Kumar, V., Das, A.K., Singh, N.K.: Development of reinforced TiN-SS316 metal matrix composite (MMC) using direct metal laser sintering (DMLS) and its characterization. Mater. Today: Proc. 4(9), 9982–9986 (2017). https://doi.org/10.1016/j.matpr.2017.06.306CrossRef

Title: Evaluation of Mechanical Properties of Ti6Al4V Built by Composite Coating of WS2, CNT, Ni, and Ti6Al4V Powders Through Laser Cladding Process
Authors: Shakti Kumar
Umar Arif
Vikas Kumar
M. Anand
R. Tyagi
Amitava Mandal
A. K. Das
Publisher: Springer Singapore
Book: Advances in Micro and Nano Manufacturing and Surface Engineering
Print ISBN: 978-981-329-424-0

Electronic ISBN: 978-981-329-425-7

Copyright Year: 2019
DOI: https://doi.org/10.1007/978-981-32-9425-7_58

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Premium Partners