Top

The International Journal of Advanced Manufacturing Technology

Published in:

12-02-2022 | ORIGINAL ARTICLE

Influence of micro sandblasting on the surface integrity of the AlTiN-coated tools

Authors: Zhou Yu, Yujuan Dong, Guangming Zheng, Xiuli Jiang, Xiang Cheng, Xianhai Yang, Kaishuo Chang, Xuewei Li

Published in: The International Journal of Advanced Manufacturing Technology | Issue 1-2/2022

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

Due to the high-efficiency, environmental protection, the low-cost, micro sandblasting technology is used in the surface treatment of the coated tools. The simulation and application of the coated tool micro sandblasting are carried out to reveal the surface treatment mechanism and analyze the influence of sandblasting parameters on the tool surface integrity. The flow field erosion simulation model of abrasive water–air three-phase flow is established. Moreover, the cutting experiments are conducted to verify the effect of micro sandblasting. The results show that the maximum velocity and pressure are obtained at the center of jet flow. The pressure distribution on the target surface has little correlation with the distance to the nozzle. The surface morphology of the AlTiN-coated tool changes obviously after micro sandblasting. Moreover, the low surface roughness R_a of the blasted tool can be obtained at the small sandblasting pressure and time. Additionally, the residual compressive stress on the surface of the AlTiN-coated tool is enhanced after micro sandblasting. The longer cutting time of the AlTiN-coated tool can be obtained at the sandblasting pressure of 0.3 MPa and sandblasting time of 3 s. This work has practical significance for optimizing micro sandblasting process and improving the surface integrity of coated tools.

previous article Experimental measurement and modeling of film thickness distribution in film insert injection molding process

next article Stability analysis and experimental research on ultrasonic cutting of wave-absorbing honeycomb material with disc cutter

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

Azim S, Gangopadhyay S, Mahapatra SS, Mittal R, Singh RK (2020) Role of PVD coating on wear and surface integrity during environment-friendly micro-drilling of Ni-based superalloy. J Clean Prod 272:122741. https://doi.org/10.1016/j.jclepro.2020.122741CrossRef

Zoei MS, Sadeghi MH, Salehi M (2016) Effect of grinding parameters on the wear resistance and residual stress of HVOF-deposited WC-10Co-4Cr coating. Surf Coat Technol 307:886–891. https://doi.org/10.1016/j.surfcoat.2016.09.067CrossRef

Bouzakis K-D, Charalampous P, Kotsanis T, Skordaris G, Bouzakis E, Denkena B, Breidenstein B, Aurich JC, Zimmermann M, Herrmann T, M’saoubi R (2017) Effect of HM substrates’ cutting edge roundness manufactured by laser machining and micro-blasting on the coated tools’ cutting performance. CIRP J Manuf Sci Technol 18:188–197. https://doi.org/10.1016/j.cirpj.2017.02.003CrossRef

Yunata EE, Aizawa T, Tamaoki K, Kasugi M (2017) Plasma polishing and finishing of cvd-diamond coated WC (Co) dies for dry stamping. Procedia Eng 207:2197–2202. https://doi.org/10.1016/j.proeng.2017.10.981CrossRef

Qin Y, Zhao H, Li C, Lu J, He J (2020) Effect of heat treatment on the microstructure and corrosion behaviors of reactive plasma sprayed TiCN coatings. Surf Coat Technol 398:126086. https://doi.org/10.1016/j.surfcoat.2020.126086CrossRef

Giti R, Haghdoost S, Ansarifard E (2020) Effect of different coloring techniques and surface treatment methods on the surface roughness of monolithic zirconia. Dent Res J 17:152–161. https://doi.org/10.4103/1735-3327.280893CrossRef

Jacoba A, Gangopadhyay S, Satapathy A, Mantry S, Jhab BB (2017) Influences of micro sandblasting as surface treatment technique on properties and performance of the AlTiN coated tools. J Manuf Process 29:407–418. https://doi.org/10.1016/j.jmapro.2017.08.013CrossRef

Bouzakis K-D, Klocke F, Skordaris G, Bouzakis E, Gerardis S, Katirtzoglou G, Makrimallakis S (2011) Influence of dry micro-blasting grain quality on wear behaviour of TiAlN coated tools. Wear 271:783–791. https://doi.org/10.1016/j.wear.2011.03.010CrossRef

Bouzakis K-D, Skordaris G, Bouzakis E, Tsouknidas A, Makrimallakis S, Gerardis S, Katirtzoglou G (2011) Optimization of wet micro-blasting on PVD films with various grain materials for improving the coated tools’ cutting performance. CIRP Ann Manuf Technol 60:587–590. https://doi.org/10.1016/j.cirp.2011.03.012CrossRef

10.

Abusuilik SB, Inoue K (2013) Effects of intermediate surface treatments on corrosion resistance of cathodic arc PVD hard coatings. Surf Coat Technol 237:421–428. https://doi.org/10.1016/j.surfcoat.2013.09.026CrossRef

11.

Abusuilik SB (2015) Pre-, intermediate, and post-treatment of hard coatings to improve their performance for forming and cutting tools. Surf Coat Technol 284:384–395. https://doi.org/10.1016/j.surfcoat.2015.07.003CrossRef

12.

Chang K, Zheng G, Cheng X, Xu R, Li Y, Yu Z, Yang X (2021) Surface integrity evolution and wear evolution of the micro-blasted coated tool in high-speed turning of Ti6Al4V. Int J Adv Manuf Technol 115:603–616. https://doi.org/10.1007/s00170-021-07227-8CrossRef

13.

Petrogalli C, Montesano L, Pola A, Gelfi M, Ghidini A, LaVecchiaa GM (2015) Improvement of fatigue resistance of a tool steel by surface treatments. Procedia Eng 109:154–161. https://doi.org/10.1016/j.proeng.2015.06.227CrossRef

14.

Tanaka S, Shirochi T, Nishizawa H, Metoki K, Miura H, Hara H, Takahashi T (2016) Micro-blasting effect on fracture resistance of PVD-AlTiN coated cemented carbide cutting tools. Surf Coat Technol 308:337–340. https://doi.org/10.1016/j.surfcoat.2016.07.094CrossRef

15.

Puneet C, Valleti K, Gopal AV (2017) Influence of surface preparation on the tool life of cathodic arc PVD coated twist drills. J Manuf Process 27:233–240. https://doi.org/10.1016/j.jmapro.2017.05.011CrossRef

16.

Liu C, Liu Z, Wang B (2018) Modification of surface morphology to enhance tribological properties for CVD coated cutting tools through wet micro blasting post-process. Ceram Int 44:3430–3439. https://doi.org/10.1016/j.ceramint.2017.11.142CrossRef

17.

Shen T, Zhu L, Liu Z (2020) Effect of micro-blasting on the tribological properties of TiN/MT-TiCN/Al₂O₃ /TiCNO coatings deposited by CVD. Int J Refract Metal Hard Mater 88:105205. https://doi.org/10.1016/j.ijrmhm.2020.105205CrossRef

18.

Mundotia R, Kothari DC, Kale A, Mhatre U, Date K, Thorat N, Ghorudea T (2020) Effect of ion bombardment and micro sandblasting on the wear resistance properties of hard TiN coatings. Mater Today Proc 26:603–612. https://doi.org/10.1016/j.matpr.2019.12.171CrossRef

19.

Faksa L, Daves W, Ecker W, Klünsner T, Tkadletz M, Czettl C (2019) Effect of shot peening on residual stresses and crack closure in CVD coated hard metal cutting inserts. Int J Refract Metal Hard Mater 82:174–182. https://doi.org/10.1016/j.ijrmhm.2019.04.008CrossRef

20.

Gruber DP, Kiefer D, Rössler R, Beckmann F, Tkadletz M, Klünsner T, Czettl C, Keckes J, Gibmeier J (2019) 20 Hz synchrotron X-ray diffraction analysis in laser-pulsed WC-Co hard metal reveals oscillatory stresses and reversible composite plastificationm. Int J Refract Metal Hard Mater 82:121–128. https://doi.org/10.1016/j.ijrmhm.2019.04.004CrossRef

21.

Thakur RK, Singh KK (2020) Experimental investigation and optimization of abrasive water jet machining parameter on multi-walled carbon nanotube doped epoxy/carbon laminate. Measurement 164:108093. https://doi.org/10.1016/j.measurement.2020.108093CrossRef

22.

Bouzakis K-D, Makrimallakis S, Katirtzoglou G, Skordaris G, Gerardis S, Bouzakis E, Leyendecker T, Bolz S, Koelkerc W (2010) Adaption of graded Cr/CrN-interlayer thickness to cemented carbide substrates’ roughness for improving the adhesion of HPPMS PVD films and the cutting performance. Surf Coat Technol 205:1564–1570. https://doi.org/10.1016/j.surfcoat.2010.09.010CrossRef

23.

Melentiev R, Fang F (2019) Investigation of erosion temperature in micro-blasting. Wear 420–421:123–132. https://doi.org/10.1016/j.wear.2018.12.073CrossRef

24.

Bar-Hen M, Etsion I (2017) Experimental study of the effect of coating thickness and substrate roughness on tool wear during turning. Tribol Int 110:341–347. https://doi.org/10.1016/j.triboint.2016.11.011CrossRef

25.

Shen X, Wang X, Sun F, Ding C (2017) Sandblasting pretreatment for deposition of diamond films on WC-Co hard metal substrates. Diam Relat Mater 73:7–14. https://doi.org/10.1016/j.diamond.2016.10.025CrossRef

Title: Influence of micro sandblasting on the surface integrity of the AlTiN-coated tools
Authors: Zhou Yu
Yujuan Dong
Guangming Zheng
Xiuli Jiang
Xiang Cheng
Xianhai Yang
Kaishuo Chang
Xuewei Li
Publication date: 12-02-2022
Publisher: Springer London
Published in: The International Journal of Advanced Manufacturing Technology / Issue 1-2/2022
Print ISSN: 0268-3768
Electronic ISSN: 1433-3015
DOI: https://doi.org/10.1007/s00170-022-08890-1

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 1-2/2022

Numerical simulation of end face heating in alternating current flash butt welding based on electrical–thermal bidirectional coupling

Modeling of thrust and torque for drilling PTFE materials

Mathematical modelling with experimental correlation for multiple craters dimension, material removal rate and surface roughness in electrical discharge machining

Comprehensive study on shape shifting behaviors in FDM-based 4D printing of bilayer structures

Study on quarter-wave generation mechanism in DP980 steel during cold rolling

Circle detection with model fitting in polar coordinates for glass bottle mouth localization

Premium Partners