Top

European Journal of Wood and Wood Products

Published in:

19-04-2022 | Original Article

Mechanical properties of aramid fiber reinforced polymer confined laminated bamboo lumber column under cyclic loading

Authors: Haitao Li, Ben Chen, Benhua Fei, Hang Li, Zhenhua Xiong, Rodolfo Lorenzo, Changhua Fang, Mahmud Ashraf

Published in: European Journal of Wood and Wood Products | Issue 5/2022

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

This paper explores the effect of using fiber-reinforced polymer (FRP) wrap on the hysteresis curve, skeleton curve, bearing capacity, stiffness and ductility of short laminated bamboo lumber (LBL) columns under cyclic loading. Aramid fiber reinforced polymer (AFRP) was used in the current study to prevent premature failure of LBL columns through confinement. Test results showed that AFRP confined short LBL columns failed mostly due to overall bending whilst some specimens showed end crushing. The ultimate bearing capacity, stiffness and ductility coefficients of AFRP confined short columns were considerably higher than those for unconfined short columns. The stress–strain curves of the specimens under cyclic loads were lower than those of the specimens under monotonic loads. Finally, this paper put forward the calculation equations of the stress–strain curves and the skeleton curves of the specimens under cyclic loads, and the proposed equation is able to accurately predict the entire cyclic stress–strain response.

previous article Load-carrying capacity prediction of single rods glued into cross-laminated timber

next article Experimental investigation of end-notched glulam beams reinforced with GFRP bars

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Wirtschaft"

Online-Abonnement

Mit Springer Professional "Wirtschaft" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 340 Zeitschriften

aus folgenden Fachgebieten:

Bauwesen + Immobilien
Business IT + Informatik
Finance + Banking
Management + Führung
Marketing + Vertrieb
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

Assima D, Li HT, Xiong ZH, Rodolfo L (2021) A review of mechanical behavior of structural laminated bamboo lumber. Sustainable Struct 1(1):000004. https://doi.org/10.54113/j.sust.2021.000004CrossRef

Chen G, Jiang H, Yu Y, Zhou T, Wu J, Li X (2020) Experimental analysis of nailed LBL-to-LBL connections loaded parallel to grain. Mater Struct Constr 53:1–13. https://doi.org/10.1617/s11527-020-01517-5CrossRef

Cheng GS, Li HT, Li H, Mahmud A (2022) Compression resistance of short LBL columns with local damage after retrofitting using basalt fiber reinforced polymer. J Build Eng. https://doi.org/10.1016/j.jobe.2021.103941CrossRef

Correal JF, Echeverry JS, Ramírez F, Yamín LE (2014) Experimental evaluation of physical and mechanical properties of Glued Laminated Guadua angustifolia Kunth. Constr Build Mater 73:105–112. https://doi.org/10.1016/j.conbuildmat.2014.09.056CrossRef

Dong JF, Jia P, Yuan SC, Wang QY (2015) Compressive behaviours of square timber columns reinforced by partial wrapping of FRP sheets. Mater Res Innov 19:S1465–S1468. https://doi.org/10.1179/1432891715Z.0000000001593CrossRef

Felice CP, Di CA, Lamarucciola N, Domenico N (2021) Experimental estimation of energy dissipated by multistorey post-tensioned timber framed buildings with anti-seismic dissipative devices. Sustain Struct 1(2):000007. https://doi.org/10.54113/j.sust.2021.000007CrossRef

GB/T 50329-2012 (2012) Standard for test methods of timber structure. Ministry of Housing and Urban-Rural development of the People’s Republic of China

Harries KA, Bumstead J, Richard M, Trujillo D (2017) Geometric and material effects on bamboo buckling behaviour. Proc Inst Civ Eng Struct Build 170:236–249. https://doi.org/10.1680/jstbu.16.00018CrossRef

Kadykova YA, Artemenko SE, Vasil’eva OV, Leont’ev AN (2003) Physicochemical reaction in polymer composite materials made from carbon, glass, and basalt fibres. Fibre Chem 35:455–457. https://doi.org/10.1023/B:FICH.0000020779.53675.20CrossRef

Kaminski S, Laurence A, Trujillo D (2016) Structural use of bamboo.: Part 1: introduction to bamboo. Struct Eng 94:40–43

Li Y, Dong WY (2012) The anti-seismic numerical simulation for a multi-storey frame with bamboo engineering materials. Adv Mater Res 450–451:1284–1287CrossRef

Li YJ, Lou ZC (2021) Progress of bamboo flatten technology research. J For Eng 6:14–23. https://doi.org/10.13360/j.issn.2096-1359.202012021CrossRef

Li HT, Zhang QS, Huang DS, Deeks AJ (2013a) Compressive performance of laminated bamboo. Compos Part B Eng 54:319–328. https://doi.org/10.1016/j.compositesbCrossRef

Li L, Yuan SL, Dong JF, Wang QY (2013b) An experimental study on the axial compressive behavior of timber columns strengthened by FRP sheets with different wrapping methods. Appl Mech Mater 351–352:1419–1422. https://doi.org/10.4028/www.scientific.net/AMM.351-352.1419CrossRef

Li HT, Su JW, Zhang QS, Deeks AJ, Hui D (2015) Mechanical performance of laminated bamboo column under axial compression. Compos Part B Eng 79:374–382. https://doi.org/10.1016/j.compositesb.2015.04.027CrossRef

Li HT, Deeks AJ, Zhang QS, Wu G (2016) Flexural performance of laminated bamboo lumber beams. Bio Resources 11:929–943

Li H, Wu G, Zhang Q, Deeks AJ, Su J (2018) Ultimate bending capacity evaluation of laminated bamboo lumber beams. Constr Build Mater 160:365–375. https://doi.org/10.1016/j.conbuildmat.2017.11.058CrossRef

Li H, Li HT, Hong C, Xiong Z, Lorenzo R, Corbi I et al (2021a) Experimental investigation on axial compression behavior of laminated bamboo lumber short columns confined with CFRP. Compos Part A Appl Sci Manuf 150:106605. https://doi.org/10.1016/j.compositesa.2021.106605CrossRef

Li B, Zhang J, Zhou XJ (2021b) Effects on the protection of bamboo by cold plasma and 2D resin-based protective agent. J For Eng 6:57–63. https://doi.org/10.13360/j.issn.2096-1359.202004027CrossRef

Liang W, Dong JF, Wang QY (2013) Mechanical study on short timber columns reinforced by different methods of FRP under axial compression. Appl Mech Mater 405–408:968–971. https://doi.org/10.4028/www.scientific.net/AMM.405-408.968CrossRef

Liu HR, Yang XM, Zhang XB (2021a) The tensile shear bonding property of flattened bamboo sheet. J For Eng 6:68–72. https://doi.org/10.13360/j.issn.2096-1359.202005029CrossRef

Liu J, Zhou AP, Sheng BL (2021b) Effect of temperature on short-term compression creep property of bamboo scrimber. J For Eng 6:64–69. https://doi.org/10.13360/j.issn.2096-1359.202006003CrossRef

Lorenzo R, Godina M, Mimendi L, Li H (2020a) Determination of the physical and mechanical properties of moso, guadua and oldhamii bamboo assisted by robotic fabrication. J Wood Sci. https://doi.org/10.1186/s10086-020-01869-0CrossRef

Lorenzo R, Mimendi L, Godina M, Li H (2020b) Digital analysis of the geometric variability of Guadua, Moso and Oldhamii bamboo. Constr Build Mater 236:117535. https://doi.org/10.1016/j.conbuildmat.2019.117535CrossRef

Luna P, Takeuchi C, Cordon E (2014) Mechanical behavior of glued laminated pressed bamboo guadua using different adhesives and environmental conditions. Key Eng Mater 600:57–68. https://doi.org/10.4028/www.scientific.net/KEM.600.57CrossRef

Lv Q, Ding Y, Liu Y (2019) Study of the bond behavior between basalt fiber-reinforced polymer bar/sheet and bamboo engineering materials. Adv Struct Eng 22:3121–3133. https://doi.org/10.1177/1369433219858725CrossRef

Ma JX, Hu P, Jiang XM, Hu M (2005) Experimental research on axial compressive behaviors for timber columns strengthened with CFRP. Industr Constr 35:40–44

Mahdavi M, Clouston PL, Arwade SR (2011) Development of laminated bamboo lumber: review of processing, performance, and economical considerations. J Mater Civ Eng 23:1036–1042. https://doi.org/10.1061/(asce)mt.1943-5533.0000253CrossRef

Mahdavi M, Clouston PL, Arwade SR (2012) A low-technology approach toward fabrication of Laminated Bamboo Lumber. Constr Build Mater 29:257–262. https://doi.org/10.1016/j.conbuildmat.2011.10.046CrossRef

Mimendi L, Lorenzo R, Li HT (2022) An innovative digital workflow to design, build and manage bamboo structures. Sustain Struct 2(1):000011. https://doi.org/10.54113/j.sust.2022.000011CrossRef

Pradhan NPN, Paraskeva TS, Dimitrakopoulos EG (2020) Quasi-static reversed cyclic testing of multi-culm bamboo members with steel connectors. J Build Eng 27:100983. https://doi.org/10.1016/j.jobe.2019.100983CrossRef

Ramberg W, Osgood R (1943) Description of stress-strain curves by three parameters. National Bureau of Standards, Washington DC

Shao Y, Zhu Z, Mirmiran A (2006) Cyclic modeling of FRP-confined concrete with improved ductility. Cem Concr Compos 28:959–968. https://doi.org/10.1016/j.cemconcomp.2006.07.009CrossRef

Sharma B, Gatóo A, Bock M, Ramage M (2015) Engineered bamboo for structural applications. Constr Build Mater 81:66–73. https://doi.org/10.1016/j.conbuildmat.2015.01.077CrossRef

Shukla SR, Kamdem DP (2012) Effect of copper based preservatives treatment of the properties of southern pine LVL. Constr Build Mater 34:593–601. https://doi.org/10.1016/j.conbuildmat.2012.02.009CrossRef

Sinha A, Way D, Mlasko D (2014) Structural performance of glued laminated bamboo beams. J Struct Eng 140:04013021. https://doi.org/10.1061/(asce)st.1943-541x.0000807CrossRef

Su JW, Li HT, Xiong ZH, Rodolfo L (2021) Structural design and construction of an office building with laminated bamboo lumber. Sustainable Struct 1(2):000010. https://doi.org/10.54113/j.sust.2021.000010CrossRef

Sun X, He M, Li Z (2020) Novel engineered wood and bamboo composites for structural applications: state-of-art of manufacturing technology and mechanical performance evaluation. Constr Build Mater 249:118751. https://doi.org/10.1016/j.conbuildmat.2020.118751CrossRef

Tian LM, Kou YF, Hao JP (2019) Axial compressive behaviour of sprayed composite mortar–original bamboo composite columns. Constr Build Mater 215:726–736. https://doi.org/10.1016/j.conbuildmat.2019.04.234CrossRef

Verma CS (2013) Chariar VM (2013) Stiffness and strength analysis of four layered laminate bamboo composites at macroscopic scale. Compos Part B Eng 45:369–376. https://doi.org/10.1016/j.compositesb.2012.07.048CrossRef

Wang XR, Zhou AP, Zhao LL, Chui HY (2019) Mechanical properties of wood columns with rectangular hollow crosssection. Constr Build Mater 214:133–142CrossRef

Wang Z, Li H, Fei B, Ashraf M, Xiong Z, Lorenzo R (2021) Axial compressive performance of laminated bamboo column with aramid fiber reinforced polymer. Compos Struct 258:113398. https://doi.org/10.1016/j.compstruct.2020.113398CrossRef

Wei Y, Zhao K, Hang C, Chen S, Ding M (2020a) Experimental study on the creep behavior of recombinant bamboo. J Renew Mater 8:251–273CrossRef

Wei Y, Tang S, Ji X, Zhao K, Li G (2020b) Stress-strain behavior and model of bamboo scrimber under cyclic axial compression. Eng Struct 209:110279. https://doi.org/10.1016/j.engstruct.2020.110279CrossRef

Xiao Y, Li Z, Wu Y (2018) Research and engineering application progress of laminated bamboo structure. Build Struct 48:84–88

Xu QF, Zhu L, Gong CC (2007) Experimental research on short timber columns strengthened with CFRP. Constr Tech 36:13–15

Yang D, Li H, Xiong Z, Mimendi L, Lorenzo R, Corbi I (2020) Mechanical properties of laminated bamboo under off-axis compression. Compos Part A Appl Sci Manuf 138:106042. https://doi.org/10.1016/j.compositesa.2020.106042CrossRef

Yu Y, Huang Y, Zhang Y, Liu R, Meng F, Yu W (2019) The reinforcing mechanism of mechanical properties of bamboo fiber bundle-reinforced composites. Polym Compos 40:1463–1472. https://doi.org/10.1002/pc.24885CrossRef

Zhang HZ (2019) Research on flexural and compressive properties of FRP bamboo matrix composites. Nanjing For Univ. https://doi.org/10.27242/d.cnki.gnjlu.2019.000289CrossRef

Zhang Y, Wei Y, Bai J, Wu G, Dong Z (2020) A novel seawater and sea sand concrete filled FRP-carbon steel composite tube column: concept and behaviour. Compos Struct 246:112421. https://doi.org/10.1016/j.compstruct.2020.112421CrossRef

Zheng JL, Qian C, Zheng JZ (1999) Experimental research on ductility of steel fiber reinforced high strength concrete column. Chin Civil Eng J 32:56–59

Zhou Y, Huang Y, Usama S, Wang Z (2021) Research on dynamic characteristics test of wooden floor structure for gymnasium. Sustain Struct 1(1):000005. https://doi.org/10.54113/j.sust.2021.000005CrossRef

Zhu YM, Yuan SC, Hou M, Wang QY (2013a) Square short wood columns strengthened with FRP sheets under compressive load. Appl Mech Mater 256–259:1008–1011. https://doi.org/10.4028/www.scientific.net/AMM.256-259.1008CrossRef

Zhu YM, Long T, Hou M, Wang QY (2013b) FRP reinforced short wood columns under axial compressive load. Adv Mater Res 671–674:484–487. https://doi.org/10.4028/www.scientific.net/AMR.671-674.484CrossRef

Title: Mechanical properties of aramid fiber reinforced polymer confined laminated bamboo lumber column under cyclic loading
Authors: Haitao Li
Ben Chen
Benhua Fei
Hang Li
Zhenhua Xiong
Rodolfo Lorenzo
Changhua Fang
Mahmud Ashraf
Publication date: 19-04-2022
Publisher: Springer Berlin Heidelberg
Published in: European Journal of Wood and Wood Products / Issue 5/2022
Print ISSN: 0018-3768
Electronic ISSN: 1436-736X
DOI: https://doi.org/10.1007/s00107-022-01816-4

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Wirtschaft"

Springer Professional "Technik"

Other articles of this Issue 5/2022

Study on properties of radiata pine wood treated with furfuryl alcohol as fretboard materials for string instruments

Mechanical, thermal and rheological properties of polylactic acid (PLA)/epichlorohydrin modified pine wood flour (EWF) composites

Characterization of particleboards of African mahogany sawdust made with tannic powders of Bridelia and African locust bean pods

Technical properties improvement of engineered flooring through hardening by acrylate surface impregnation and in-situ electron beam polymerization

Correction to: Research and prospects of bamboo bolts in China: state of the art

Study on infection behavior and characteristics of poplar wood dyed by Lasiodiplodia theobromae