Top

The International Journal of Advanced Manufacturing Technology

Published in:

28-05-2022 | ORIGINAL ARTICLE

Numerical and experimental research on warm cross wedge rolling of hollow shafts with corrugated surface

Authors: Jiaai Shi, Jinping Liu, Baoyu Wang, Jinxia Shen

Published in: The International Journal of Advanced Manufacturing Technology | Issue 1/2022

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

HCWR (hot cross wedge rolling) of hollow shafts has been investigated while there are few investigations on CWR (cross wedge rolling) of hollow shafts at other temperatures. Because of the severe oxidative decarburization of HCWR and large deformation resistance of CCWR (cold cross wedge rolling), the WCWR (warm cross wedge rolling) was proposed for forming hollow shafts to compromise these limitations. In this paper, relevant investigations about a WCWR process of hollow shafts with corrugated surface were carried out. At first, the parameters and the geometry of the WCWR rollers of hollow shafts with corrugated surface were designed. Then, the finite element (FE) model of the WCWR process was established and verified by the laboratory test. Next, the FE results with various mandrel diameters were presented, and the influence of the mandrel diameter on the distribution of stress, effective strain, and temperature and the rolling force and torque was analyzed. Finally, the experiment results with various mandrel diameters were presented, and the effect of the mandrel diameter on the forming quality was discussed. The results show that as mandrel diameter increases, the temperature of the workpiece after rolling decreases, while the effective stress and strain and the rolling torque increase. The maximum dimensional deviation at the symmetric cross section is not larger than 0.3 mm when there is no mandrel or the relative mandrel diameter is 0.7, and the roundness is gradually worse as mandrel diameter increases.

previous article Visual odometry algorithm based on geometric prior for dynamic environments

next article Concurrent layout and trajectory optimization for robot workcell toward energy-efficient and collision-free automation

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

Bartnicki J, Pater Z (2004) The aspects of stability in cross-wedge rolling processes of hollowed shafts. J Mater Process Technol 155–156:1867–1873. https://doi.org/10.1016/j.jmatprotec.2004.04.278CrossRef

Bartnicki J, Pater Z (2005) Numerical simulation of three-rolls cross-wedge rolling of hollowed shaft. J Mater Process Technol 164–165:1154–1159. https://doi.org/10.1016/j.jmatprotec.2005.02.120CrossRef

Urankar S, Lovell M, Morrow C, Li Q, Kawada K (2006) Development of a critical friction model for cross wedge rolling hollow shafts. J Mater Process Technol 177(1–3):539–544. https://doi.org/10.1016/j.jmatprotec.2006.04.048CrossRef

Urankar S, Lovell M, Morrow C, Li Q, Kawada K (2006) Establishment of failure conditions for the cross-wedge rolling of hollow shafts. J Mater Process Technol 177(1–3):545–549. https://doi.org/10.1016/j.jmatprotec.2006.04.052CrossRef

Ji H, Liu J, Wang B, Lin J, Tang X (2016) The process parameters effect of ovality in cross wedge rolling for hollow valve without mandril. MATEC Web of Conf 80:13003. https://doi.org/10.1051/matecconf/20168013003CrossRef

Neugebauer R, Glass R, Kolbe M (2002) Optimisation of processing routes for cross rolling and spin extrusion. J Mater Process Technol 125:856–862. https://doi.org/10.1016/S0924-0136(02)00392-8CrossRef

Yang C, Hu Z (2016) Research on the ovality of hollow shafts in cross wedge rolling with mandrel. Int J Adv Manuf Tech 83(1–4):67–76. https://doi.org/10.1007/s00170-015-7478-3CrossRef

Ji H, Liu J, Wang B, Fu X, Xiao W, Hu Z (2017) A new method for manufacturing hollow valves via cross wedge rolling and forging: numerical analysis and experiment validation. J Mater Process Technol 240:1–11. https://doi.org/10.1016/j.jmatprotec.2016.09.004CrossRef

Huang X, Wang B, Lin J, Zhu C (2017) Effect of mandrel diameter on non-circularity of hollow shafts in cross wedge rolling. Procedia Eng 207:2376–2381. https://doi.org/10.1016/j.proeng.2017.10.1011CrossRef

10.

Huang X, Wang B, Mu Y, Shen J, Li J, Zhou J (2019) Investigation on the effect of mandrels on hollow shafts in cross-wedge rolling. Int J Adv Manuf Tech 102(1–4):1–13. https://doi.org/10.1007/s00170-018-3093-4CrossRef

11.

Landgrebe D, Steger J, Böhmichen U, Bergmann M (2018) Modified cross-wedge rolling for creating hollow shafts. Procedia Manuf 21:53–59. https://doi.org/10.1016/j.promfg.2018.02.094CrossRef

12.

Zheng S, Shu X, Han S, Yu P (2019) Mechanism and force-energy parameters of a hollow shaft’s multi-wedge synchrostep cross-wedge rolling. J Mech Sci Technol 33(5):2075–2084. https://doi.org/10.1007/s12206-019-0411-1CrossRef

13.

Shen J, Wang B, Zhou J, Huang X, Li J (2019) Numerical and experimental research on cross wedge rolling hollow shafts with a variable inner diameter. Arch Civ Mech Eng 19(4):1497–1510. https://doi.org/10.1016/j.acme.2019.08.003CrossRef

14.

Shen J, Wang B, Yang C, Zhou J, Cao X (2021) Theoretical study and prediction of the inner hole reduction and critical mandrel diameter in cross wedge rolling of hollow shaft. J Mater Proces Technol 294:117140. https://doi.org/10.1016/j.jmatprotec.2021.117140CrossRef

15.

Lin L, Wang B, Shen J, Liu T (2021) Producing hollow shafts in a new horizontal mill by novel flat-knifing cross-wedge rolling with single guide. Int J Adv Manuf Tech. https://doi.org/10.1007/s00170-021-08023-0CrossRef

16.

Quan X, Dong D (1996) Test and research on cold wedge-cross rolling process. Forg Stamping Mach 04:24–26. https://doi.org/10.16316/j.issn.1672-0121.1996.04.010 (in Chinese)CrossRef

17.

Yan S, Li Y (1997) Experimental study on cold cross wedge rolling. Forg Stamping Technol 05:31–34. https://doi.org/10.13330/j.issn.1000-3940.1997.05.012 (in Chinese)CrossRef

18.

Pater Z, Tofil A (2007) Experimental and theoretical analysis of the cross-wedge rolling process in cold forming conditions. Arch of Metall and Mater 52(2):289–297

19.

Behrens B, Suchmann P, Schott A (2008) Warm forging: new forming sequence for the manufacturing of long flat pieces. Prod Eng Res Devel 2(3):261–268. https://doi.org/10.1007/s11740-008-0114-4CrossRef

20.

Tokita Y, Nakagaito T, Tamai Y, Urabe T (2017) Stretch formability of high strength steel sheets in warm forming. J Mater Process Technol 246:77–84. https://doi.org/10.1016/j.jmatprotec.2017.03.012CrossRef

21.

Deng Z, Chang L (2012) Warm cross wedge rolling forming analysis of steel core with cone platform and groove. Forg Stamping Technol 37(002):79–85. https://doi.org/10.3969/j.issn.1000-3940.2012.02.019(inChinese)CrossRef

22.

Huang X, Wang B, Zhou J, Ji H, Mu Y, Li J (2017) Comparative study of warm and hot cross-wedge rolling: numerical simulation and experimental trial. Int J Adv Manuf Tech 92(9–12):3541–3551. https://doi.org/10.1007/s00170-017-0399-6CrossRef

23.

Bulzak T, Pater Z, Tomczak J, Majerski K (2020) Hot and warm cross-wedge rolling of ball pins-comparative analysis. J Manuf Process 50:90–101. https://doi.org/10.1016/j.jmapro.2019.12.001CrossRef

24.

Shu X, Shi J, Chen J, Yang H (2021) Effects of process parameters on surface quality of shaft parts formed by warm cross-wedge rolling. Int J Adv Manuf Tech 113(9–10):2819–2831. https://doi.org/10.1007/s00170-021-06784-2CrossRef

25.

Huang X (2019) Research on the key technology of 40MnBH hollow shafts using cross wedge rolling with mandrel control process. Dissertation, University of Science and Technology Beijing (in Chinese)

26.

Shen J (2022) Research on the forming and microstructure evolution of hollow shaft by cross wedge rolling with mandrel. Dissertation, University of Science and Technology Beijing (in Chinese)

27.

Yang C (2014) Research on the key technology of cross wedge rolling truck hollow shaft. Dissertation, University of Science and Technology Beijing (in Chinese)

28.

Hu Z, Zhang K, Wang B, Shu X, Yang C (2004) Parts forming technology and simulation of cross wedge rolling. Metallurgical Industry Press, Beijing (in Chinese)

29.

Lin, L (2021) Research on the key technology of flexible skew rolling process for large shafts. Dissertation, University of Science and Technology Beijing (in Chinese)

30.

Wang B, Hu F, Hu F, Hu Z (2010) Experimental research on rolling radius of formed part for cross wedge rolling. J Mech Eng 46(24):22–27 (in Chinese)CrossRef

Title: Numerical and experimental research on warm cross wedge rolling of hollow shafts with corrugated surface
Authors: Jiaai Shi
Jinping Liu
Baoyu Wang
Jinxia Shen
Publication date: 28-05-2022
Publisher: Springer London
Published in: The International Journal of Advanced Manufacturing Technology / Issue 1/2022
Print ISSN: 0268-3768
Electronic ISSN: 1433-3015
DOI: https://doi.org/10.1007/s00170-022-09379-7

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 1/2022

DPDSN: data plane deadline-sensitive scheduling in data center networks

A systematic method for automated manufacturability analysis of machining parts

A comparative study on surface topography and microhardness of laser polished-hardened AISI D2 tool steel

Dynamic simulation and experimental study of cutting force by rake angle of multi-axis high-speed ball-end milling tool

Structural design and kinematic analysis of a welding robot for liquefied natural gas membrane tank automatic welding

Concurrent layout and trajectory optimization for robot workcell toward energy-efficient and collision-free automation

Premium Partners