Top

European Journal of Wood and Wood Products

Published in:

04-05-2021 | Original Article

Effects of laser parameters on the width of color change area of poplar wood surface during a single irradiation

Authors: Rongrong Li, Chujun He, Yingjing Chen, Xiaodong Wang

Published in: European Journal of Wood and Wood Products | Issue 5/2021

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

Due to the high efficiency, flexible moving trajectory and good controllability, laser surface treatment is a modification method used for wood materials, which could be applied to change the wood properties of color, wettability, surface roughness, etc. These surface properties directly affect the wood products coating performance, such as coating adhesion and surface gloss. To reveal the width of the heat-affected zone under laser treatment with different laser parameter combinations, the width of color change area (WCCA) during a single irradiation was measured. The laser power, feed speed and focus plane position were chosen as input parameters. The response surface methodology was selected to arrange the experiments, analyze the influences of laser parameters on WCCA and establish a relationship between laser parameters and WCCA. The results showed that the laser power and focus plane position had significant influences on WCCA. The values of WCCA increased with increased laser power and focus plane position within certain limit. The quadratic model for establishing the relationship between laser parameters and WCCA was significant. The value of correlation coefficient (R²) is very close to 1, which means that the model could give an accurate prediction of WCCA under variable modification parameter combinations.

previous article Laser beam calibration for wood surface colour treatment

next article Dielectric and surface properties of wood modified with NaCl aqueous solutions and treated with FE-DBD atmospheric plasma

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Wirtschaft"

Online-Abonnement

Mit Springer Professional "Wirtschaft" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 340 Zeitschriften

aus folgenden Fachgebieten:

Bauwesen + Immobilien
Business IT + Informatik
Finance + Banking
Management + Führung
Marketing + Vertrieb
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

Cao Y, Wang X, Li Y, Shen D, Dai Y, Zhang S, Zhang W (2020) Effect of high temperature oil heat treatment on the starch content and mold-resistant property of bamboo. J Forest Eng 5:109–115. https://doi.org/10.13360/j.issn.2096-1359.201905016CrossRef

Eltawahni HA, Olabi AG, Benyounis KY (2011) Investigating the CO₂ laser cutting parameters of MDF wood composite material. Opt Laser Technol 43:648–659. https://doi.org/10.1016/j.optlastec.2010.09.006CrossRef

Eltawahni HA, Rossini NS, Dassisti M, Alrashed K, Aldaham TA, Benyounis KY, Olabi AG (2013) Evalaution and optimization of laser cutting parameters for plywood materials. Opt Lasers Eng 51:1029–1043. https://doi.org/10.1016/j.optlaseng.2013.02.019CrossRef

Fang L, Xiong X, Wang X, Chen H, Mo X (2017) Effects of surface modification methods on mechanical and interfacial properties of high-density polyethylene-bonded wood veneer composites. J Wood Sci 63:65–73CrossRef

Fukuta S, Nomura M, Ikeda T, Yoshizawa M (2016) UV laser machining of wood. Eur J Wood Prod 74:261–267CrossRef

Gao X, Zhou F, Fu Z, Zhou Y (2018) Sorption isotherms characteristics of high temperature heat-treated Picea abies and Pseudotsuga menziesii. J Forest Eng 3:25–29. https://doi.org/10.13360/j.issn.2096-1359.2018.04.004

Gaspar P, Rocha M, Kearns A, Watkins K, Vilar R (2000) A study of the effect of the wavelength in the Q-switched Nd:YAG laser cleaning of gilded wood. J Cult Herit 1:133–144. https://doi.org/10.1016/S1296-2074(00)00157-6CrossRef

Gu L, Ding T, Jiang N (2019) Development of wood heat treatment research and industrialization. J Forest Eng 4:1–11. https://doi.org/10.13360/j.issn.2096-1359.2019.04.001

Guo X, Lin Y, Na B, Liang X, Ekevad M, Ji F, Huang L (2017) Evaluation of physical and mechanical properties of fiber-reinforced poplar scrimber. BioResources 12:43–55. https://doi.org/10.15376/biores.12.1.43-55

Gurau L, Petru A, Varodi A, Timar MC (2017) The influence of CO₂ laser beam power output and scanning speed on surface roughness and colour changes of beech (Fagus sylvatica). Bioresources 12:7395–7412. https://doi.org/10.15376/biores.12.4.7395-7412CrossRef

Haller P, Beyer E, Wiedemann G, Panzner M, Wust H (2002) Experimental study of the effect of a laser beam on the morphology of wood surfaces. In: Paper presented at the first international conference of the european society for wood mechanics, Lausanne, Switzerland, 19–21 April

Hernandez-Castaneda JC, Sezer HK, Li L (2010) Dual gas jet-assisted fibre laser blind cutting of dry pine wood by statistical modelling. Int J Adv Manuf Technol 50:195–206. https://doi.org/10.1007/s00170-009-2491-zCrossRef

Kačík F, Kubovský I (2011) Chemical changes of beech wood due to CO₂ laser irradiation. J Photochem Photobiol A 222:105–110. https://doi.org/10.1016/j.jphotochem.2011.05.008CrossRef

Kubovský I, Kacik F (2013) Changes of the wood surface colour induced by CO₂ laser and its duralibity after the xenon lamp exposure. Wood Res 58:581–590

Kúdela J, Reinprecht L, Vidholdová Z, Andrejko M (2019) Surface properties of beech wood modified by CO₂ laser. Acta Facultatis Xylologiae Zvolen 61:5–18. https://doi.org/10.1016/j.biortech.2007.04.021CrossRef

Kúdela J, Kubovský I, Andrejko M (2020) Surface properties of beech wood after CO₂ laser engraving. Coatings 10:77. https://doi.org/10.3390/coatings10010077CrossRef

Li R, Xu W, Wang X, Wang C (2018) Modeling and predicting of the color changes of wood surface during CO₂ laser modification. J Clean Prod 183:818–823. https://doi.org/10.1016/j.jclepro.2018.02.194CrossRef

Li R, Fang L, Xu W, Xiong X, Wang XA (2019) Effect of laser irradiation on the surface wettability of poplar wood. Sci Adv Mater 11:655–660. https://doi.org/10.1166/sam.2019.3450CrossRef

Liu Y, Hu J (2021) Investigation of polystyrene-based microspheres from different copolymers and their structural color coatings wood surface. Coatings 11(1):14. https://doi.org/10.3390/coatings11010014CrossRef

Liu Y, Hu J, Wu Z (2020) Fabrication of coatings with structural color on a wood surface. Coatings 10:32. https://doi.org/10.3390/coatings10010032CrossRef

Martinez-Conde A, Krenke T, Frybort S, Mueller U (2017) Review: Comparative analysis of CO₂ laser and conventional sawing for cutting of lumber and wood-based materials. Wood Sci Technol 51:943–966. https://doi.org/10.1007/s00226-017-0914-9CrossRef

Mishra S, Yadava V (2015) Laser beam micromachining (LBMM)—a review. Opt Lasers Eng 73:89–122. https://doi.org/10.1016/j.optlaseng.2015.03.017CrossRef

Nath S, Waugh DG, Ormondroyd GA, Spear MJ, Pitman AJ, Sahoo S, Curling SF, Mason P (2020) CO₂ laser interactions with wood tissues during single pulse laser-incision. Opt Laser Technol 126:106069. https://doi.org/10.1016/j.optlastec.2020.106069CrossRef

Ruan X, Wang R, Luo J, Yao Y, Liu T (2018) Experimental and modeling study of CO₂ laser writing induced polyimide carbonization process. Materials Des 160:1168–1177. https://doi.org/10.1016/j.matdes.2018.10.050CrossRef

Salloom R, Joshi SS, Dahotre NB, Srinivasan SG (2020) Laser surface engineering of B4C/Fe nano composite coating on low carbon steel: experimental coupled with computational approach. Materials Design 190:108576. https://doi.org/10.1016/j.matdes.2020.108576CrossRef

Sernek M (2015) Reasons for colour changes during thermal and hydrothermal treatment of wood. Zbornik Gozdarstva in Lesarstva:145–151

Vidholdová Z, Reinprecht L, Igaz R (2017) The impact of laser surface modification of beech wood on its color and occurrence of molds. Bioresources 12:4177–4186. https://doi.org/10.15376/biores.12.2.4177-4186

Wang H, Huang L, Cao P, Ji F, Yang G, Guo X, Li R (2017) Investigation of shear strength of engineered wood flooring bonded with PUR by response surface methodology. BioResources 12:3656–3665. https://doi.org/10.15376/biores.12.2.3656-3665

Xiong X, Yuan Y, Niu Y, Zhang L, Wu Z (2020) Effects of different treatments on surface activity of rice straw particleboard. Sci Adv Mater 12:289–295. https://doi.org/10.1166/sam.2020.3528CrossRef

Zhan T, Sun F, Lv C, He Q, Wang X, Xu K, Zhang Y, Cai L (2019) Evaluation of moisture diffusion in lignocellulosic biomass in steady and unsteady states by a dynamic vapor sorption apparatus. Holzforschung 73:1113–1119CrossRef

Zhang J, Chesnokova T, Zhang B, Zhan J (2020) Chromatic variability of larch wood impacted by high-temperature thermal treatment and oil-wax coating. J Forest Eng 5:64–75. https://doi.org/10.13360/j.issn.2096-1359.202003012CrossRef

Zhou B, Mahdavian SM (2004) Experimental and theoretical analyses of cutting nonmetallic materials by low power CO₂-laser. J Materials Process Technol 146:188–192. https://doi.org/10.1016/j.matprotec.2003.10.017CrossRef

Zhou S, Wang L, Liang Y, Zhu Y, Jian R, Wang B, Wang L, Xue Y, Wang F, Cai H, Ren Y (2020) A strategy to achieve high-strength WNiFe composite-like alloys with low W content by laser melting deposition. Mater Des 190:108554. https://doi.org/10.1016/j.matdes.2020.108554CrossRef

Zhu Z, Buck D, Cao P, Guo X, Wang J (2020a) Assessment of cutting forces and temperature in tapered milling of stone-plastic composite using response surface methodology. JOM 72:3917–3925CrossRef

Zhu Z, Buck D, Guo X, Cao P (2020b) High-quality and high-efficiency machining of stone-plastic composite with diamond helical cutters. J Manuf Process 58:914–922CrossRef

Title: Effects of laser parameters on the width of color change area of poplar wood surface during a single irradiation
Authors: Rongrong Li
Chujun He
Yingjing Chen
Xiaodong Wang
Publication date: 04-05-2021
Publisher: Springer Berlin Heidelberg
Published in: European Journal of Wood and Wood Products / Issue 5/2021
Print ISSN: 0018-3768
Electronic ISSN: 1436-736X
DOI: https://doi.org/10.1007/s00107-021-01706-1

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Wirtschaft"

Springer Professional "Technik"

Other articles of this Issue 5/2021

Integration of market aspects into material development: approach and exemplification for a wood composite

Monitoring seasonal transpiration drying of loblolly and slash pine with time domain reflectometry

Effects of interconnections between timber floor elements: dynamic and static evaluations of structural scale tests

Bamboo flattening technique: a literature and patent review

Correction to: Dielectric and surface properties of wood modified with NaCl aqueous solutions and treated with FE-DBD atmospheric plasma

Classification of wood species using spectral and texture features of transverse section