Top

The International Journal of Advanced Manufacturing Technology

Published in:

09-11-2021 | Technical Note

Manufacturing of Ti6Al4V alloy part reinforced by silicon carbide fibers by laser powder bed fusion with following hot isostatic pressing

Authors: Andrey Travyanov, Pavel Petrovskiy, Ivan Logachev, Andrey Lagutin, Vladimir Cheverikin, Maxim Khomutov, Dmitrii Zhigalov, Anton Klyuyev

Published in: The International Journal of Advanced Manufacturing Technology | Issue 1-2/2022

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

In this work, the hybrid approach combining the laser powder bed fusion and encapsulated hot isostatic pressing was applied for the elaboration of composite part consisting of titanium alloy matrix reinforced by silicon carbide fibers. The feasibility of the proposed approach was experimentally confirmed. The fiber-reinforced titanium alloy parts with a volume fraction of fibers equal to 17% were successfully manufactured. X-ray tomography revealed the absence of defects in obtained part and good contact between the matrix and the fibers. EBSD analysis revealed that fibers’ presence did not influence the orientation of grains in the titanium matrix. The three-point flexural tests revealed that the composite part had significantly higher yield strength than the part produced from bulk titanium alloy.

previous article Positioning error compensation of a flexible track hybrid robot for aircraft assembly based on response surface methodology and experimental study

next article Thanking reviewers

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

MacKay RA, Brindley PK, Froes FH (1991) Continuous fiber-reinforced titanium aluminide composites. JOM 435(43):23–29. https://doi.org/10.1007/BF03220564CrossRef

Qu H, Ren X, Hou H et al (2011) Interfacial behaviors in SiC fiber reinforced titanium matrix composites during thermal exposure. Adv Mater Res 295–297:880–885. https://doi.org/10.4028/www.scientific.net/AMR.295-297.880

Carrère N, Kruch S, Vassel A, Chaboche JL (2002) Damage mechanisms in unidirectional SiC/Ti composites under transverse creep loading: experiments and modeling. Int J Damage Mech 11:41–63. https://doi.org/10.1106/105678902022261CrossRef

Carrere N, Martin E, Coutand B (2003) Creep behaviour of a unidirectional SM1140 + /Ti-6242 composite. Compos Part A Appl Sci Manuf 34:1065–1073. https://doi.org/10.1016/S1359-835X(03)00212-4CrossRef

Majumdar BS, Newaz GM (1995) Constituent damage mechanisms in metal matrix composites under fatigue loading, and their effects on fatigue life. Mater Sci Eng A 200:114–129. https://doi.org/10.1016/0921-5093(95)07010-9CrossRef

Wang PC, Jeng SM, Yang JM, Mal AK (1996) Fatigue life prediction of fiber-reinforced titanium matrix composites. Acta Mater 44:1097–1108. https://doi.org/10.1016/1359-6454(95)00202-2CrossRef

Martin E, CarrÉre N (2012) Metal matrix composites: continuous silicon-carbide fibers/titanium-alloy matrix. Wiley Encycl Compos. https://doi.org/10.1002/9781118097298.WEOC139CrossRef

Leyens C, Hausmann J, Kumpfert J (2003) Continuous fiber reinforced titanium matrix composites: fabrication, properties and applications. Adv Eng Mater 5:399–410. https://doi.org/10.1002/ADEM.200310093CrossRef

Leucht R, Dudek HJ (1994) Properties of SiC-fibre reinforced titanium alloys processed by fibre coating and hot isostatic pressing. Mater Sci Eng A 188:201–210. https://doi.org/10.1016/0921-5093(94)90373-5CrossRef

10.

Baik KH (2006) Tensile failure behavior of SiC/Ti-6Al-4V composites manufactured by plasma spraying route. Mater Trans 47:2815–2820. https://doi.org/10.2320/MATERTRANS.47.2815CrossRef

11.

Rahman KM, Vorontsov VA, Flitcroft SM, Dye D (2017) A high strength Ti–SiC metal matrix composite. Adv Eng Mater 19:1700027. https://doi.org/10.1002/ADEM.201700027CrossRef

12.

Kazantseva NV, Krakhmalev PV, Yadroitsava IA (2021) Laser additive 3D printing of titanium alloys: current status, problems, trends. Phys Met Metallogr 1221(122):6–25. https://doi.org/10.1134/S0031918X21010063CrossRef

13.

DebRoy T, Wei HL, Zuback JS et al (2018) Additive manufacturing of metallic components – process, structure and properties. Prog Mater Sci 92:112–224. https://doi.org/10.1016/J.PMATSCI.2017.10.001CrossRef

14.

O’Regan P, Prickett P, Setchi R et al (2016) Metal based additive layer manufacturing: variations, correlations and process control. Procedia Comput Sci 96:216–224. https://doi.org/10.1016/J.PROCS.2016.08.134CrossRef

15.

Wu MW, Lai PH (2016) The positive effect of hot isostatic pressing on improving the anisotropies of bending and impact properties in selective laser melted Ti-6Al-4V alloy. Mater Sci Eng A 658:429–438. https://doi.org/10.1016/J.MSEA.2016.02.023CrossRef

16.

Tammas-williams S, Withers PJ, Todd I, Prangnell PB (2016) The effectiveness of hot isostatic pressing for closing porosity in titanium parts manufactured by selective electron beam melting. Metall Mater Trans A 47. https://doi.org/10.1007/s11661-016-3429-3

17.

Petrovskiy P, Travyanov A, Cheverikin VV et al (2020) Effect of encapsulated hot isostatic pressing on properties of Ti6Al4V deposits produced by cold spray. Int J Adv Manuf Technol 107:437–449. https://doi.org/10.1007/s00170-020-05080-9CrossRef

18.

Dyer A, Jones J, Cutts R, Whittaker M (2019) The effect of phase angle on the thermo-mechanical fatigue life of a titanium metal matrix composite. Mater, (2019) Vol 12. Page 953(12):953. https://doi.org/10.3390/MA12060953

19.

Rafi HK, Karthik NV, Gong H et al (2013) Microstructures and mechanical properties of Ti6Al4V parts fabricated by selective laser melting and electron beam melting. J Mater Eng Perform 2212(22):3872–3883. https://doi.org/10.1007/S11665-013-0658-0CrossRef

20.

Lui EW, Xu W, Pateras A et al (2017) New development in selective laser melting of Ti–6Al–4V: a wider processing window for the achievement of fully lamellar α + β microstructures. JOM 6912(69):2679–2683. https://doi.org/10.1007/S11837-017-2599-9CrossRef

21.

Legrand N, Remy L, Molliex L, Dambrine B (2002) Damage mechanisms and life prediction in high temperature fatigue of a unidirectional SiC–Ti composite. Int J Fatigue 24:369–379. https://doi.org/10.1016/S0142-1123(01)00092-5CrossRef

22.

Thomas MP, Howard G, Pather R et al (2001) Comparison of low cycle fatigue performance of several [0] Sigma fibre reinforced titanium matrix composites. Int J Fatigue 23:851–856. https://doi.org/10.1016/S0142-1123(01)00056-1CrossRef

23.

Thomas MP (2003) Effect of matrix and fibre type on low cycle fatigue of [90]8 Sigma fibre reinforced titanium matrix composite. Compos Sci Technol 63:587–595. https://doi.org/10.1016/S0266-3538(02)00264-6CrossRef

24.

González C, Llorca J (2001) Micromechanical modelling of deformation and failure in Ti–6Al–4V/SiC composites. Acta Mater 49:3505–3519. https://doi.org/10.1016/S1359-6454(01)00246-4CrossRef

25.

Weber CH, Chen X, Connell SJ, Zok FW (1994) On the tensile properties of a fiber reinforced titanium matrix composite—I. Unnotched behavior Acta Metall Mater 42:3443–3450. https://doi.org/10.1016/0956-7151(94)90477-4CrossRef

26.

Bettge D, Günther B, Wedell W et al (2007) Mechanical behavior and fatigue damage of a titanium matrix composite reinforced with continuous SiC fibers. Mater Sci Eng A 452–453:536–544. https://doi.org/10.1016/J.MSEA.2006.10.107CrossRef

Title: Manufacturing of Ti6Al4V alloy part reinforced by silicon carbide fibers by laser powder bed fusion with following hot isostatic pressing
Authors: Andrey Travyanov
Pavel Petrovskiy
Ivan Logachev
Andrey Lagutin
Vladimir Cheverikin
Maxim Khomutov
Dmitrii Zhigalov
Anton Klyuyev
Publication date: 09-11-2021
Publisher: Springer London
Published in: The International Journal of Advanced Manufacturing Technology / Issue 1-2/2022
Print ISSN: 0268-3768
Electronic ISSN: 1433-3015
DOI: https://doi.org/10.1007/s00170-021-08307-5

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 1-2/2022

A novel intelligent manufacturing mode with human-cyber-physical collaboration and fusion in the non-ferrous metal industry

Announcement of the B. John Davies Prize for the best paper published in IJAMT in 2020

Optimization and effects of machining parameters on delamination in drilling of pure and Al2O3/SiO2-added GFRP composites

Prediction and experimental investigation of depth of subsurface damage in semi-consolidated abrasive grinding of cleavable gallium oxide crystals

Enhanced feedrate scheduling algorithm for CNC system with acceleration look-ahead and sin2 acceleration profile

Thermal finite element modeling of the laser beam welding of tailor welded blanks through an equivalent volumetric heat source

Premium Partners