Top

The International Journal of Advanced Manufacturing Technology

Published in:

03-02-2022 | ORIGINAL ARTICLE

Modeling and analysis of tool-chip contact model during quasi-intermittent vibration assisted swing cutting based on two-zone theory

Authors: Limin Zhang, Nan Li, Mingming Lu, Jiakang Zhou, Yubo Jin, Yuyang Liu

Published in: The International Journal of Advanced Manufacturing Technology | Issue 1-2/2022

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

Quasi-intermittent vibration assisted swing cutting (QVASC) is a new processing method with the advantages of quasi-intermittent cutting and friction reversal. In the cutting process, it is important to study the tool-chip friction characteristics for reducing the cutting force, tool wear and improving the surface quality of the workpiece. This paper divides the tool-chip contact interface (TCI) based on the two-zone analysis modeling method during QVASC. The proposed model includes the primary shear zone, the secondary shear zone and the TCI. The friction coefficient equations of sticking, sliding and the whole part are expressed, and the physical properties of each zone in the machining process are comprehensively described. The theoretical simulation and experimental verification are carried out, and it is found that the proposed model is in good agreement with the experimental results. When the cutting speed is 7.85–11.78 m/min, the theoretical and experimental cutting force error of QVASC is less than 15%. The results show that the model provides an analysis method that can effectively predict the contact characteristics of the TCI during QVASC processing. The cutting force of QVASC is significantly less than traditional continuous cutting, which can reduce the cutting force.

previous article In-process material removal rate monitoring for abrasive belt grinding using multisensor fusion and 2D CNN algorithm

next article Numerical modelling and experimental analysis on angular strain induced by bead-on-plate SS316L GMAW using inherent strain and thermomechanical methods

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

Pramanik A, Islam MN, Basak A, Littlefair G (2013) Machining and tool wear mechanisms during machining titanium alloys. Adv Mater Res 651:338–343. https://doi.org/10.4028/www.scientific.net/AMR.651.338CrossRef

Wang ZG, Rahman M, Wong YS (2005) Tool wear characteristics of binderless CBN tools used in high-speed milling of titanium alloys. Wear 258:752–758. https://doi.org/10.1016/j.wear.2004.09.066CrossRef

Cui CX, Hu BM, Zhao LC, Liu SJ (2011) Titanium alloy production technology, market prospects and industry development. Mater Des 32:1684–1691. https://doi.org/10.1016/j.matdes.2010.09.011CrossRef

Wei WH, Xu JH, Fu YC, Yang SB (2012) Tool wear in turning of titanium alloy after thermohydrogen treatment. Chin J Mech Eng 25:776–780. https://doi.org/10.3901/CJME.2012.04.776CrossRef

Kikuchi M (2009) The use of cutting temperature to evaluate the machinability of titanium alloys. Acta Biomater 5:770–775. https://doi.org/10.1016/j.actbio.2008.08.016CrossRef

Shamoto E, Moriwaki T (1994) Study on elliptical vibration cutting. CIRP Ann 43:35–38. https://doi.org/10.1016/S0007-8506(07)62158-1CrossRef

Shamoto E, Moriwaki T (1999) Ultaprecision diamond cutting of hardened steel by applying elliptical vibration cutting. CIRP Ann 48:441–444. https://doi.org/10.1016/S0007-8506(07)63222-3CrossRef

Moriwaki T, Shamoto E (1995) Ultrasonic elliptical vibration cutting. CIRP Ann 44:31–34. https://doi.org/10.1016/S0007-8506(07)62269-0CrossRef

Shamoto E, Morimoto Y, Moriwaki T (1999) Elliptical vibration cutting (2nd Report) - study on effects of vibration conditions. J Jpn Soc Precis Eng 65:411–417CrossRef

10.

Shamoto E, Suzuki N, Hino R (2008) Analysis of 3D elliptical vibration cutting with thin shear plane model. CIRP Ann – Manuf Technol 57:57–60. https://doi.org/10.1016/j.cirp.2008.03.073

11.

Lu MM, Zhou JK, Lin JQ, Gu Y, Han JG, Zhao DP (2017) Study on Ti-6Al-4V alloy machining applying the non-resonant three-dimensional elliptical vibration cutting. Micromachines 8:306. https://doi.org/10.3390/mi8100306CrossRef

12.

Lu MM, Zhao DP, Lin JQ, Zhou XQ, Zhou JK, Chen B, Wang H (2018) Design and analysis of a novel piezoelectrically actuated vibration assisted rotation cutting system. Smart Mater Struct 27:095020

13.

Fang N (2002) Machining with tool–chip contact on the tool secondary rake face—Part I: a new slip-line model. Int J Mech Sci 44:2337–2354. https://doi.org/10.1016/S0020-7403(02)00185-6CrossRefMATH

14.

Zhang CY, Lu JP, Zhang FP, Butt SI (2017) Identification of a new friction model at tool-chip interface in dry orthogonal cutting. Int J Adv Manuf Technol 89:921–932CrossRef

15.

Zorev NN (1966) Metal cutting mechanics. Pergamon Press

16.

Qi HS, Mills B (2000) Formation of a transfer layer at the tool-chip interface during machining. Wear 245:136–147. https://doi.org/10.1016/S0043-1648(00)00474-9CrossRef

17.

Moufki A, Molinari A, Dudzinski D (1998) Modelling of orthogonal cutting with a temperature dependent friction law. J Mech Phys Solids 46:2103–2138. https://doi.org/10.1016/S0022-5096(98)00032-5CrossRefMATH

18.

Shan CW, Zhang MH, Zhang SN, Dang J (2020) Prediction of machining-induced residual stress in orthogonal cutting of Ti6Al4V. Int J Adv Manuf Technol 107:2375–2385. https://doi.org/10.1007/s00170-020-05181-5CrossRef

19.

Hua J, Shivpuri R (2005) A cobalt diffusion based model for predicting crater wear of carbide tools in machining titanium alloys. J Eng Mater Technol 127:136–144. https://doi.org/10.1115/1.1839192CrossRef

20.

Patil S, Joshi S, Tewari A, Joshi SS (2014) Modelling and simulation of effect of ultrasonic vibrations on machining of Ti6Al4V. Ultrasonics 54:694–705. https://doi.org/10.1016/j.ultras.2013.09.010CrossRef

21.

Koseki S, Inoue K, Sekiya K, Morito S, Ohba T, Usuki H (2017) Wear mechanisms of PVD-coated cutting tools during continuous turning of Ti-6Al-4V alloy. Precis Eng 47:434–444. https://doi.org/10.1016/j.precisioneng.2016.09.018CrossRef

22.

Bai W, Sun R, Roy A, Silberschmidt VV (2017) Improved analytical prediction of chip formation in orthogonal cutting of titanium alloy Ti6Al4V. Int J Mech Sci 133:357–367. https://doi.org/10.1016/j.ijmecsci.2017.08.054CrossRef

23.

Sánchez HY, Trujillo VFJ, Bermudo GC, Sevilla HL (2018) Experimental parametric relationships for chip geometry in dry machining of the Ti6Al4V alloy. Materials 11:1260. https://doi.org/10.3390/ma11071260CrossRef

24.

Lu ZH, Zhang DY, Zhang XY, Peng JL (2020) Effects of high-pressure coolant on cutting performance of high-speed ultrasonic vibration cutting titanium alloy. J Mater Process Technol 279:116584. https://doi.org/10.1016/j.jmatprotec.2019.116584CrossRef

25.

Lu MM, Chen B, Lin JQ, Zhao DP, Zhou JK, Yi A, Zhu ZM (2020) Friction modeling of tool-chip interface based on shear-slip theory for vibration assisted swing cutting. J Manuf Process 55:240–248. https://doi.org/10.1016/j.jmapro.2020.03.052CrossRef

26.

Lu MM, Chen JZ, Zhao DP, Lin JQ, Zhu ZM, Chen B, Yi A (2019) Modeling and realization of work-space analysis of a piezoelectric actuator 2-DOF vibration-assisted swing cutting system. Appl Nanosci 11:777–785. https://doi.org/10.1007/s13204-019-01079-1CrossRef

27.

Childs THC, Mahdi MI, Barrow G (1989) On the stress distribution between the chip and tool during metal turning. CIRP Ann Manuf Technol 38:55–58. https://doi.org/10.1016/S0007-8506(07)62651-1CrossRef

28.

Sutter G, List G (2013) Very high speed cutting of Ti-6A1-4V titanium alloy - change in morphology and mechanism of chip formation. Int J Mach Tools Manuf 66:37–43. https://doi.org/10.1016/j.ijmachtools.2012.11.004CrossRef

29.

Qi HS, Mills B (2003) Modelling of the dynamic tool–chip interface in metal cutting. J Mater Process Technol 138:201–207. https://doi.org/10.1016/S0924-0136(03)00072-4CrossRef

30.

Childs THC (2006) Friction modelling in metal cutting. Wear 260:310–318. https://doi.org/10.1016/j.wear.2005.01.052CrossRef

31.

Dudzinski D, Molinari A (1997) A modelling of cutting for viscoplastic materials. Int J Mech Sci 39:369–389. https://doi.org/10.1016/S0020-7403(96)00043-4CrossRefMATH

32.

Johnson GR (1983) A constitutive model and data for metals subjected to large strains, high strain rates and high temperatures. In: Proc 7th Int Symp Ballist 541–547

33.

Oxley PLB, Young HT (1990) The mechanics of machining: an analytical approach to assessing machinability. Wear 150:380–381. https://doi.org/10.1115/1.2888318CrossRef

34.

Oxley PLB, Hastings WF (1976) Minimum work as a possible criterion for determining the frictional conditions at the tool/chip interface in machining. Philos Trans R Soc London Ser Math Phys Sci 282:565–584. https://doi.org/10.1098/rsta.1976.0064CrossRef

35.

Marinov VR (2001) Hybrid analytical–numerical solution for the shear angle in orthogonal metal cutting — Part I: Theoretical foundation. Int J Mech Sci 43:399–414. https://doi.org/10.1016/S0020-7403(00)00013-8CrossRefMATH

36.

Marinov VR (2001) Hybrid analytical–numerical solution for the shear angle in orthogonal metal cutting — Part II: Experimental verification. Int J Mech Sci 43:415–426CrossRef

37.

Bahi S, Nouari M, Moufki A, Mansori ME, Molinari A (2012) Hybrid modelling of sliding–sticking zones at the tool–chip interface under dry machining and tool wear analysis. Wear 286:45–54. https://doi.org/10.1016/j.wear.2011.05.001CrossRef

Title: Modeling and analysis of tool-chip contact model during quasi-intermittent vibration assisted swing cutting based on two-zone theory
Authors: Limin Zhang
Nan Li
Mingming Lu
Jiakang Zhou
Yubo Jin
Yuyang Liu
Publication date: 03-02-2022
Publisher: Springer London
Published in: The International Journal of Advanced Manufacturing Technology / Issue 1-2/2022
Print ISSN: 0268-3768
Electronic ISSN: 1433-3015
DOI: https://doi.org/10.1007/s00170-021-08620-z

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 1-2/2022

An improved method for manufacturing sheet-tube connection structure by double-sided annular sheet squeezing

Electrorheological fluid–assisted ultrasonic polishing for IN625 additively manufactured surfaces

Recent progress in minimizing the warpage and shrinkage deformations by the optimization of process parameters in plastic injection molding: a review

Analysis and optimization of the properties of the grinding contact line for form-grinding modified helical gears

Numerical modelling and experimental analysis on angular strain induced by bead-on-plate SS316L GMAW using inherent strain and thermomechanical methods

Extreme pressure and antiwear additives for lubricant: academic insights and perspectives

Premium Partners