Top

Journal of Materials Engineering and Performance

Published in:

03-02-2020

Studies on Creep and Wear Behavior of Mo-40Ti-10Si Alloy Prepared by Hot Pressing

Authors: Bhaskar Paul, A. Sarkar, J. Kishor, S. Majumdar

Published in: Journal of Materials Engineering and Performance | Issue 2/2020

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

The present study deals with the development and characterization of a Mo-Ti-Si alloy by pressure-assisted sintering for high-temperature applications. The three-phase alloy was found to be consisted of (Mo,Ti)₃Si-type silicide and discontinuous Mo-rich and Ti-rich α-(Mo, Ti)_ss phases. The alloy was characterized for mechanical properties, creep, and wear behavior. Elastic modulus and hardness of all the constituent phases were determined using nanoindentation technique. Creep properties of the alloy determined from the compression creep tests in vacuum were found to be better than the single-phase Mo₅Si₃ and Ti₅Si₃ at the tested temperature of 1000 °C. The coefficient of friction values were found to be 0.59, 0.55 and 0.4 at the testing loads of 10, 15 and 20 N, respectively, at 10 Hz frequency in reciprocal testing mode at room temperature, while 0.42 at 500 °C with a load of 15 N. The dominant wear mechanism was proposed based on the wear scar analysis.

previous article Structure Optimization and Cutting Performance of Gradient Multilayer AlCrSiN Films with Ion Source Etching Pretreatment

next article Microstructural Evolution of SA508 Grade 3 Steel during Hot Deformation

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

W.O. Soboyejo and T.S. Srivatsan, Advanced Structural Materials: Properties, Design Optimization, and Applications, W.O. Soboyejo and T.S. Srivatsan, Ed., CRC Press, Boca Raton, FL, 2007, p 475–493

S.E.G. Mohamed and J.-M. Tournier, A Review of Refractory Metal Alloys and Mechanically Alloyed-Oxide Dispersion Strengthened Steels for Space Nuclear Power Systems, J. Nuclear Mater., 2005, 340, p 93–112CrossRef

G. Meetham, M. van de Voorde, L. Mishnaevsky Jr., Materials for High Temperature Engineering Applications. Appl. Mech. Rev. 2001, 54, p 19–24CrossRef

D.M. Dimiduk and J.H. Perepezko, Mo-Si-B Alloys: Developing a Revolutionary Turbine Engine Material, MRS Bull., 2003, 28(9), p 639–645CrossRef

J.H. Perepezko, R. Sakidja, K.S. Kumar, and W. Soboyejo, Ed., Advanced Structural Materials: Properties, Design Optimization, and Applications, CRC Press, Boca Raton, FL, 2007

B.P. Bewlay, M.R. Jackson, P.R. Subramanian, and J.C. Zhao, A Review of Very-Hightemperature Nb-Silicide-Based Composites, Metall. Mater. Trans. A, 2003, 34, p 2043–2052CrossRef

R. Mitra, Mechanical Behaviour and Oxidation Resistance of Structural Silicides, Int. Mater. Rev., 2006, 51, p 13–64CrossRef

T. Moriyama, K. Yoshimi, M. Zhao, T. Masnou, T. Yokoyama, J. Nakamura, H. Katsui, and T. Goto, Room-Temperature Fracture Toughness of MoSiBTiC Alloys, Intermetallics, 2017, 84, p 92–102CrossRef

M. Zhao, S. Nakayama, T. Hatakeyama, J. Nakamura, and K. Yoshimi, Microstructure, High-Temperature Deformability and Oxidation Resistance of a Ti5Si3-Containing Multiphase MoSiBTiC Alloy, Intermetallics, 2017, 90, p 169–179CrossRef

10.

Y. Yang, Y.A. Chang, L. Tan, and Y. Du, Experimental Investigation and Thermodynamic Descriptions of the Mo-Si-Ti System, Mater. Sci. Eng. A, 2003, 362, p 281CrossRef

11.

Y. Yang, Y.A. Chang, L. Tan, and W. Cao, Multiphase Equilibria in the Metal-Rich Region of the Mo-Ti-Si-B System: Thermodynamic Prediction and Experimental Validation, Acta Mater., 2005, 53, p 1711–1720CrossRef

12.

D. Schliephake, A. Kauffmanna, X. Conga, C. Gombolaa, M. Azim, B. Gorr, H.J. Christ, and M. Heilmaier, Constitution, Oxidation and Creep of Eutectic and Eutectoid Mo-Si-Ti Alloys, Intermetallics, 2019, 104, p 133–142CrossRef

13.

M.A. Azim, D. Schliephake, C. Hochmuth, B. Gorr, H.J. Christ, U. Glatzel, and M. Heilmaier, Creep Resistance and Oxidation Behavior of Novel Mo-Si-B-Ti Alloys, JOM, 2015, 67(11), p 2621–2628CrossRef

14.

S. Majumdar, B. Paul, P.K. Singh, J. Kishor, and V. Kain, Effect of Si Content on Microstructure, Mechanical and Oxidation Properties of Hot Pressed Mo-Ti-Si Alloys, Intermetallics, 2018, 100, p 126–135CrossRef

15.

S. Burk, B. Gorr, H.J. Christ, and D. Schliephake, Schliephake, High-Temperature Oxidation Behaviour of a Single-Phase (Mo,Ti)₅Si₃ (Mo-Si-Ti) alloy, Scr Mater, 2012, 66(5), p 223–226CrossRef

16.

I.V. Dulera and R.K. Sinha, Indian High Temperature Reactor Programme: An Overview, BARC Newsletter, 2010, 315, p 65–69

17.

J. Pelleg, Time Dependent Deformation—Creep in Silicides. In: Mechanical Properties of Silicon Based Compounds: Silicides. Engineering Materials. (Springer, Cham, 2019)CrossRef

18.

J. Xu, Z.Y. Li, X. Lu, Y. Yan, P. Munroe, and Z.H. Xie, Mechanical and Electrochemical Properties of Nanocrystalline (Mo_1-xCr_x)₃Si Coatings: Experimental and Modelling Studies, J. Alloys Compd., 2014, 611, p 179–190CrossRef

19.

A. Misra, J.J. Petrovic, and T.E. Mitchell, Microstructures and Mechanical Properties of a Mo₃Si-Mo₅Si₃ Composite Scr, Mater., 1999, 40(2), p 191–196

20.

I. Rosales and J.H. Schneibel, Stoichiometry and Mechanical Properties of Mo₃Si, Intermetallics, 2000, 8, p 885–889CrossRef

21.

D. Schliephake, The Influence of Fe on Ti-Containing Mo-Si-B Alloys: Phase Formation, Microstructure and Pressure Creep Behaviour, Karlsruhe Institute of Technology, Dissertation, 2017

22.

D.M. Shah, D. Berczik, D.L. Anton, and R. Hecht, Appraisal of Other Silicides as Structural Materials, Mater. Sci. Eng. A, 1992, 155, p 45–57CrossRef

23.

R.A. Michi, G.K. Byung-Wook, K. Wooyoung, L. David, and C. Dunand, Compressive Creep Behavior of Hot-Pressed Mg1.96Al0.04Si0.97Bi0.03, Scr. Mater., 2018, 148, p 10–14CrossRef

24.

K. Sadananda, C.R. Feng, R. Mitra, and S.C. Deevi, Creep and Fatigue Properties of High Temperature Silicides and Their Composites, Mater. Sci. Eng. A, 1999, 261, p 223–238CrossRef

25.

Oxidation and Creep Behavior of Mo₅Si₃ Based Materials, Meyer, Mitch, PhD Thesis Submitted to Iowa State University, Ames Laboratory, U.S. DOE Iowa State University Ames, Iowa 50011 Date Transmitted: June 19, 1995

26.

K. Sadananda and C.R. Feng, Effect of Carbon Addition on the Creep of Molybdenum Disilicide Composites, Mater. Sci. Eng., A, 1995, 192, p 862–867CrossRef

27.

R. Rosenkranz, G. Frommeyer, and W. Smarsly, Microstructures and Properties of High Melting Point Intermetallic Ti₅Si₃ and TiSi₂ Compounds, Mater. Sci. Eng. A, 1992, 152, p 288–294CrossRef

28.

B.P. Bewlay, M.R. Jackson, and M.F.X. Gigliotti, Intermetallic Compounds-Principles and Practice, Chapter 26, Vol 3, R.L. Fleischer and J.H. Westbrook, Ed., Wiley, Hoboken, 2001, p 541–560

29.

B.P. Bewlay, M.R. Jackson, J.C. Zhao, P.R. Subramanian, M.G. Mendiratta, and J.J. Lewandowski, Ultrahigh-Temperature Nb-Silicide-Based Composites, MRS Bull., 2003, 28(9), p 646–653CrossRef

30.

G. Hasemann, I. Bogomol, D. Schliephake, P.I. Loboda, and M. Krüger, Microstructure and Creep Properties of a Near-Eutectic Directionally Solidified Multiphase Mo-Si-B Alloy, Intermetallics, 2014, 48, p 28–33CrossRef

31.

B. Paul, K. Raju, M. Vadsola, T.S.R.C. Murthy, J. Kishora, P. Arora, P. Chakraborty, K. Singh, S. Majumdar, and V. Kain, Investigations on Wear and Liquid Metal Corrosion Behavior of Aluminized IN-RAFMS, Fusion Eng. Des., 2018, 128, p 204–214CrossRef

32.

G. Theiler and T. Gradt, Friction and Wear of PEEK Composites in Vacuum Environment, Wear, 2010, 269, p 278–284CrossRef

33.

J. Cheng, J. Zhen, S. Zhu, J. Yang, J. Mab, W. Li, and W. Liu, Friction and Wear Behavior of Ni-Based Solid-Lubricating Composites at High Temperature in a Vacuum Environment, Mater. Des., 2017, 122, p 405–413CrossRef

34.

V. Ramana Posa, A. Viswadevarayalu, and A. Reddy Somala, Fabrication of Graphene-TiO₂ Nanocomposite with Improved Photocatalytic Degradation for Acid Orange 7 Dye Under Solar Light Irradiation, Bull. Mater. Sci., 2016, 39(3), p 759–767CrossRef

35.

K.J. Kingma and R.J. Hemley, Raman Spectroscopic Study of Microcrystalline Silica, Am. Mineral., 1994, 79, p 269–273

36.

W. Marscher, A Phenomenological Model of Abradable Wear in High Performance Turbomachinery, Wear, 1980, 59(1), p 191–211CrossRef

37.

D. Klaffke, Fretting Wear of Ceramics, Tribol. Int., 1989, 22(2), p 89–101CrossRef

Title: Studies on Creep and Wear Behavior of Mo-40Ti-10Si Alloy Prepared by Hot Pressing
Authors: Bhaskar Paul
A. Sarkar
J. Kishor
S. Majumdar
Publication date: 03-02-2020
Publisher: Springer US
Published in: Journal of Materials Engineering and Performance / Issue 2/2020
Print ISSN: 1059-9495
Electronic ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-020-04603-5

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 2/2020

An Investigation into Thermal History and Its Correlation with Mechanical Properties of PA12 Parts Produced by Selective Laser Sintering Process

Improved Mechanical Properties, Wear and Corrosion Resistance of 316L Steel by Homogeneous Chromium Nitride Layer Synthesis Using Plasma Nitriding

Effect of Welding Parameters on Microstructure and Mechanical Properties of Friction-Stir-Welded Al-Mg-Si Alloy

Effect of Sodium Dodecyl Sulfate on Mechanical Properties and Electrical Conductivity of Nanotwinned Copper

Microstructures and Properties of Graphite Nanoflake/6061Al Matrix Composites Fabricated via Spark Plasma Sintering

Effects of Ce on DO3-Ordered Phase, Coincident Site Lattice Grain Boundary and Plastic Deformation of Fe-6.9 Wt.%Si Alloy

Premium Partners