Top

Journal of Materials Engineering and Performance

Published in:

20-06-2017

Surface Characteristics of Machined NiTi Shape Memory Alloy: The Effects of Cryogenic Cooling and Preheating Conditions

Authors: Y. Kaynak, B. Huang, H. E. Karaca, I. S. Jawahir

Published in: Journal of Materials Engineering and Performance | Issue 7/2017

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

This experimental study focuses on the phase state and phase transformation response of the surface and subsurface of machined NiTi alloys. X-ray diffraction (XRD) analysis and differential scanning calorimeter techniques were utilized to measure the phase state and the transformation response of machined specimens, respectively. Specimens were machined under dry machining at ambient temperature, preheated conditions, and cryogenic cooling conditions at various cutting speeds. The findings from this research demonstrate that cryogenic machining substantially alters austenite finish temperature of martensitic NiTi alloy. Austenite finish (A _f) temperature shows more than 25 percent increase resulting from cryogenic machining compared with austenite finish temperature of as-received NiTi. Dry and preheated conditions do not substantially alter austenite finish temperature. XRD analysis shows that distinctive transformation from martensite to austenite occurs during machining process in all three conditions. Complete transformation from martensite to austenite is observed in dry cutting at all selected cutting speeds.

previous article Evaluation of the Effect of Different Plasma-Nitriding Parameters on the Properties of Low-Alloy Steel

next article Study on Microtexture and Martensite Formation of Friction Stir Lap-welded DP 590 Steel within A1 to A3 Temperature Range

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

T. Baxevanis, A. Cox, and D. Lagoudas, Micromechanics of Precipitated Near-Equiatomic Ni-Rich NiTi Shape Memory Alloys, Acta Mech., 2014, 225, p 1–19CrossRef

S.A. Shabalovskaya, On the Nature of the Biocompatibility and on Medical Applications of NiTi Shape Memory and Superelastic Alloys, Biomed. Mater. Eng., 1996, 6, p 267–289

S.A. Fadlallah, N. El-Bagoury, S.M. Gad El-Rab, R.A. Ahmed, and G. El-Ousamii, An Overview of NiTi Shape Memory Alloy: Corrosion Resistance and Antibacterial Inhibition for Dental Application, J. Alloys Compd., 2014, 583, p 455–464CrossRef

K. Gall, J. Tyber, G. Wilkesanders, S.W. Robertson, R.O. Ritchie, and H.J. Maier, Effect of Microstructure on the Fatigue of Hot-Rolled and Cold-Drawn NiTi Shape Memory Alloys, Mater. Sci. Eng. A, 2008, 486, p 389–403CrossRef

D.A. Miller and D.C. Lagoudas, Thermomechanical Characterization of NiTiCu and NiTi SMA Actuators: Influence of Plastic Strains, Smart Mater. Struct., 2000, 9, p 640–652CrossRef

J.A. Shaw and S. Kyriakides, Thermomechanical Aspects of NiTi, J. Mech. Phys. Solids, 1995, 43, p 1243–1281CrossRef

D.A. Miller and D.C. Lagoudas, Influence of Cold Work and Heat Treatment on the Shape Memory Effect and Plastic Strain Development of NiTi, Mater. Sci. Eng. A Struct., 2001, 308, p 161–175CrossRef

Y. Kaynak, H. Karaca, R. Noebe, and I. Jawahir, Analysis of Tool-Wear and Cutting Force Components in Dry, Preheated, and Cryogenic Machining of NiTI, Shape Memory Alloys, Procedia CIRP, 2013, 8, p 498–503CrossRef

Y. Kaynak, H.E. Karaca, R.D. Noebe, and I.S. Jawahir, Tool-Wear Analysis in Cryogenic Machining of NiTi Shape Memory Alloys: A Comparison of Tool-Wear Performance with Dry and MQL Machining, Wear, 2013, 306, p 51–63CrossRef

10.

K. Weinert and V. Petzoldt, Machining of NiTi Based Shape Memory Alloys, Mater. Sci. Eng. A, 2004, 378, p 180–184CrossRef

11.

H.-C. Kim, J. Yum, B. Hur, and G.S.-P. Cheung, Cyclic Fatigue and Fracture Characteristics of Ground and Twisted Nickel-Titanium Rotary Files, J. Endod., 2010, 36, p 147–152CrossRef

12.

H. Huang, A study of High-Speed Milling Characteristics of Nitinol, Mater. Manuf. Process., 2004, 19, p 159–175CrossRef

13.

Y. Kaynak, H. Karaca, and I.S. Jawahir, Cryogenic Machining of NiTi Shape Memory Alloy, 6th International Conference and Exhibition on Design and Production of Machines and Dies/Molds, 2011, p 23–26

14.

Y. Kaynak, H. Tobe, R.D. Noebe, H. Karaca, and I.S. Jawahir, The Effects of Machining on Microstructure and Transformation behavior of NiTi Alloy, Scr. Mater., 2014, 74, p 60–63CrossRef

15.

Y. Kaynak, H. Karaca, and I.S. Jawahir, Surface Integrity Characteristics of NiTi Shape Memory Alloys Resulting from Dry and Cryogenic Machining, Procedia CIRP, 2014, 13, p 393–398CrossRef

16.

Y. Kaynak, Machining and Phase Transformation Response of Room-Temperature Austenitic NiTi Shape Memory Alloy, J. Mater. Eng. Perform., 2014, 23, p 3354–3360CrossRef

17.

Y. Kaynak, H.E. Karaca, and I.S. Jawahir, Cutting Speed Dependent Microstructure and Transformation Behavior of NiTi Alloy in Dry and Cryogenic Machining, J. Mater. Eng. Perform., 2015, 24, p 452–460CrossRef

18.

A.P. Stebner, S.C. Vogel, R.D. Noebe, T.A. Sisneros, B. Clausen, D.W. Brown, A. Garg, and L.C. Brinson, Micromechanical Quantification of Elastic, Twinning, and Slip Strain Partitioning Exhibited by Polycrystalline, Monoclinic Nickel-Titanium During Large Uniaxial Deformations Measured via In-Situ Neutron Diffraction, J. Mech. Phys. Solids, 2013, 61, p 2302–2330CrossRef

19.

O. Benafan, S.A. Padula, R.D. Noebe, T.A. Sisneros, and R. Vaidyanathan, Role of B19′ Martensite Deformation in Stabilizing Two-Way Shape Memory Behavior in NiTi, J. Appl. Phys., 2012, 112, p 093510–093511CrossRef

20.

K. Otsuka and X. Ren, Physical Metallurgy of Ti-Ni-Based Shape Memory Alloys, Prog. Mater. Sci., 2005, 50, p 511–678CrossRef

21.

Y. Kaynak, H.E. Karaca, R.D. Noebe, and I. Jawahir, The Effect of Active Phase of The Work Material on Machining Performance of a NiTi Shape Memory Alloy, Metall. Mater. Trans. A, 2015, 46, p 2625–2636CrossRef

22.

V. Sharma and M. Pandey, Optimization of Machining and Vibration Parameters for Residual Stresses Minimization in Ultrasonic Assisted Turning of 4340 Hardened Steel, Ultrasonics, 2016, 70, p 172–182CrossRef

23.

A. Thakur and S. Gangopadhyay, State-of-the-Art in Surface Integrity in Machining of Nickel-Based Super Alloys, Int. J. Mach. Tools Manuf., 2016, 100, p 25–54CrossRef

24.

Q. Wang and Z. Liu, Plastic Deformation Induced Nano-Scale Twins in Ti-6Al-4V Machined Surface with High Speed Machining, Mater. Sci. Eng. A, 2016, 675, p 271–279CrossRef

25.

G. Rotella, O.W. Dillon, Jr., D. Umbrello, L. Settineri, and I.S. Jawahir, The Effects of Cooling Conditions on Surface Integrity in Machining of Ti6Al4V Alloy, Int. J. Adv. Manuf. Technol., 2014, 71, p 47–55CrossRef

26.

B.D. Cullity and S.R. Stock, Elements of X-Ray Diffraction, Prentice Hall, Upper Saddle River, 2001

27.

M.E. Mitwally and M. Farag, Effect of Cold Work and Annealing on the Structure and Characteristics of NiTi Alloy, Mater. Sci. Eng. A, 2009, 519, p 155–166CrossRef

28.

I. Karaman, H.E. Karaca, Z. Luo, and H. Maier, The Effect of Severe Marforming on Shape Memory Characteristics of a Ti-Rich NiTi alloy Processed Using Equal Channel Angular Extrusion, Metall. Mater. Trans. A, 2003, 34, p 2527–2539CrossRef

29.

H. Shahmir, M. Nili-Ahmadabadi, M. Mansouri-Arani, and T.G. Langdon, The Processing of NiTi Shape Memory Alloys by Equal-Channel Angular Pressing at Room Temperature, Mater. Sci. Eng. A, 2013, 576, p 178–184CrossRef

30.

D.N.A. Shri, K. Tsuchiya, and A. Yamamoto, Surface Characterization of TiNi Deformed by High-Pressure Torsion, Appl. Surf. Sci., 2014, 289, p 338–344CrossRef

31.

J. Uchil, F. Fernandes, and K. Mahesh, X-Ray Diffraction Study of the Phase Transformations in NiTi Shape Memory Alloy, Mater. Charact., 2007, 58, p 243–248CrossRef

32.

S. De la Flor, C. Urbina, and F. Ferrando, Effect of Mechanical Cycling on Stabilizing the Transformation Behaviour of NiTi Shape Memory Alloys, J. Alloys Compd., 2009, 469, p 343–349CrossRef

33.

J. Olbricht, A. Yawny, A. Condó, F. Lovey, and G. Eggeler, The Influence of Temperature on the Evolution of Functional Properties During Pseudoelastic Cycling of Ultra Fine Grained NiTi, Mater. Sci. Eng. A, 2008, 481, p 142–145CrossRef

34.

Y. Kaynak, Process-Induced Surface Integrity in Machining of NiTi Shape Memory Alloys, University of Kentucky. Ph.D. Dissertation (2013)

35.

A.S. Mahmud, H. Yang, S. Tee, G. Rio, and Y. Liu, Effect of Annealing on Deformation-Induced Martensite Stabilisation of NiTi, Intermetallics, 2008, 16, p 209–214CrossRef

36.

Y. Liu and D. Favier, Stabilisation of Martensite Due to Shear Deformation via Variant Reorientation in Polycrystalline NiTi, Acta Mater., 2000, 48, p 3489–3499CrossRef

37.

H. Lin, S. Wu, T. Chou, and H. Kao, The Effects of Cold Rolling on the Martensitic Transformation of an Equiatomic TiNi Alloy, Acta Metall. Mater., 1991, 39, p 2069–2080CrossRef

38.

Y. Liu and Z. Xie, Detwinning in Shape Memory Alloy, Progress in Smart Materials and Structures, P.L. Reece, Ed., Nova Science Publishers Inc, NY, 2007, p 29–65

39.

G. Tan and Y. Liu, Comparative Study of Deformation-Induced Martensite Stabilisation via Martensite Reorientation and Stress-Induced Martensitic Transformation in NiTi, Intermetallics, 2004, 12, p 373–381CrossRef

40.

J.T. Lim and D.L. McDowell, Degradation of an Ni-Ti Alloy During Cyclic Loading, 1994 North American Conference on Smart Structures and Materials, International Society for Optics and Photonics, 1994, p 326–341

Title: Surface Characteristics of Machined NiTi Shape Memory Alloy: The Effects of Cryogenic Cooling and Preheating Conditions
Authors: Y. Kaynak
B. Huang
H. E. Karaca
I. S. Jawahir
Publication date: 20-06-2017
Publisher: Springer US
Published in: Journal of Materials Engineering and Performance / Issue 7/2017
Print ISSN: 1059-9495
Electronic ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-017-2791-7

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 7/2017

Mechanical Properties and Microstructure of Mg-SiCp Composite Sheets Fabricated by Sintering and Warm Rolling

Effect of Ce Addition on the Microstructure and Properties of Ag17CuZnSn Filler Metal

Evaluation of the Effect of Different Plasma-Nitriding Parameters on the Properties of Low-Alloy Steel

Influence of Strain Rate, Microstructure and Chemical and Phase Composition on Mechanical Behavior of Different Titanium Alloys

Effect of Cooling Rate on the Mechanical Strength of Carbon Fiber-Reinforced Thermoplastic Sheets in Press Forming

Wear Behavior of Laser-Cladded Co-Cr-Mo Coating on γ-TiAl Substrate

Premium Partners