Top

Journal of Materials Engineering and Performance

Published in:

19-04-2018

The Effect of Grain Refinement on Solid Particle Erosion of Grade 5 Ti Alloy

Authors: N. A. Kazarinov, A. D. Evstifeev, Y. V. Petrov, S. A. Atroshenko, R. R. Valiev

Published in: Journal of Materials Engineering and Performance | Issue 6/2018

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

In this work, the results on solid particle erosion of an ultrafine-grained Grade 5 titanium alloy, which was produced using high-pressure torsion (HPT) technique, are presented. In order to assess influence of the HPT treatment on material’s behavior in erosive conditions, special experimental procedures were developed. The ultrafine-grained (UFG) alloy was tested alongside with a conventional coarse-grained (CG) Grade 5 titanium alloy in equal conditions. The experiments were conducted in a small-scale wind tunnel with corundum particles as an abrasive material. Both particle dimensions and particle velocities were varied in course of the experiments. Erosion resistance of the samples was evaluated in two ways—mass reduction measurements with subsequent gravimetric erosion rate calculations and investigation of samples’ surface roughness after erosion tests. The UFG titanium alloy demonstrated considerable improvement of static mechanical properties (ultimate tensile strength, microhardness), whereas its CG counterpart appeared to be slightly more resistant to solid particle erosion, which might indicate the drop of dynamic strength properties for the HPT-processed material.

previous article Effect of Reduced Graphene Oxide Reinforcement on the Wear Characteristics of Electroless Ni-P Coatings

next article Evaluation of Delamination of X80 Pipeline Steel Coating Under Alternating Stray Current Via Scanning Electrochemical Microscopy

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

W.N. Sharpe, Ed., Springer Handbook of Experimental Solid Mechanics, Springer, US, 2008

K. Ravi-Chandar and W.G. Knauss, An Experimental Investigation into Dynamic Fracture—I. Crack Initiation and Crack Arrest, Int. J. Fract., 1984, 25, p 247–262CrossRef

A.M. Bragov, Yu.V. Petrov, B.L. Karihaloo, A.Yu. Konstantinov, D.A. Lamzin, A.K. Lomunov, and I.V. Smirnov, Dynamic Strength and Toughness of an Ultra High Performance Fibre Reinforced Concrete, Eng. Fract. Mech., 2013, 110, p 477–488CrossRef

R. Valiev, Nanostructuring of Metals by Severe Plastic, Nat. Mater., 2004, 3, p 511–516CrossRef

D.G. Morris, Mechanical Behaviour of Nanostructured Materials, Trans Tech, Uetikon, Zürich, 1998

A.B. Witney, P.G. Sanders, J.R. Weertman, and J.A. Eastman, Fatigue of Nanocrystalline Copper, Scr. Metall. Mater., 1995, 33(12), p 2025–2030CrossRef

M.Y. Murashkin, I. Sabirov, V.U. Kazykhanov, E.V. Bobruk, A.A. Dubravina, and R.Z. Valiev, Enhanced Mechanical Properties and Electrical Conductivity in Ultrafine-Grained Al Alloy Processed Via ECAP-PC, J. Mater. Sci., 2013, 48(13), p 4501–4509CrossRef

N.A. Kazarinov, A.D. Evstifeev, Y.V. Petrov, S.A. Atroshenko, V.A. Lashkov, R.Z. Valiev, and A.S. Bondarenko, Surface Roughness Investigation of Ultrafine-Grained Aluminum Alloy Subjected to High-Speed Erosion, J. Mater. Eng. Perform, 2016, 25, p 3573–3579CrossRef

P. Verleysen, W. Oelbrandt, S. Naghdy, and L. Kestens, Static and Dynamic Tensile Behaviour of Aluminium Processed by High Pressure Torsion, EPJ Web of Conferences, Vol 94, 2015. https://doi.org/10.1051/epjconf/20159402012.

10.

N. Herzig, L.W. Meyer, D. Musch, T. Halle, V.A. Skripnyak, E.G. Skripnyak, S.V. Razorenov, and L. Krüger, The Mechanical Behaviour of Ultra Fine Grained Titanium Alloys at High Strain Rates, 3rd International Conference on High Speed Forming, March 11-12, 2008 (Dortmund), 2008, p 65–74

11.

R.Z. Valiev and T.G. Langdon, Principles of equal-channel angular pressing as a processing tool for grain refinement, Prog. Mater. Sci., 2006, 51(7), p 881–981CrossRef

12.

R.Z. Valiev, R.K. Islamgaliev, and I.V. Alexandrov, Bulk nanostructured materials from severe plastic deformation, Prog. Mater. Sci., 2000, 45, p 103–189CrossRef

13.

H. Miura, G. Yu, and X. Yang, Multi-Directional Forging of AZ61 Mg Alloy Under Decreasing Temperature Conditions and Improvement of Its Mechanical Properties, Mater. Sci. Eng., A, 2011, 528(22), p 6981–6992CrossRef

14.

Y. Saito, H. Utsunomiya, N. Tsutji, and T. Sakaim, Novel Ultra-High Straining Process for Bulk Materials Development of the Accumulative Roll-Bonding (ARB) Process, Acta Mater., 1999, 47(2), p 579–583CrossRef

15.

C.P. Wang, F.G. Li, L. Wang, and H.J. Qiao, Review on Modified and Novel Techniques of Severe Plastic Deformation, Sci. China Tech. Sci., 2012, 55, p 2377–2390CrossRef

16.

T.C. Lowe and Y.T. Zhu, Commercialization of Nanostructured Metals Produced by Severe Plastic Deformation Processing, Adv. Eng. Mater., 2003, 5, p 373–378CrossRef

17.

R.Z. Valiev, I.P. Semenova, V.V. Latysh, H. Rack, T.C. Lowe, J. Petruzelka, L. Dluhos, D. Hrusak, and J. Sochova, Nanostructured Titanium for Biomedical Applications, Adv. Eng. Mater., 2008, 10(8), p B15CrossRef

18.

I.P. Semenova, G.I. Raab, and R.Z. Valiev, Nanostructured Titanium Alloys: New Developments and Application Prospects, Nanotechnol. Russ, 2014, 9(5–6), p 311–324CrossRef

19.

W. Tabakoff, High-Temperature Erosion Resistance Coatings for Use in Turbomachinery, Wear, 1995, 186–187, p 224–229CrossRef

20.

Y.V. Petrov, N.F. Morozov, and V.I. Smirnov, Structural Macromechanics Approach in Dynamics of Fracture, Fatigue Fract. Eng. Mater. Struct., 2003, 26(4), p 363–372CrossRef

21.

I.M. Hutchings, Prediction of the Resistance of Metals to Erosion by Solid Particles, Wear, 1975, 35, p 371–374CrossRef

22.

G.L. Sheldon, Effects of Surface Hardness and Other Material Properties on Erosive Wear of Metals by Solid Particles, J. Eng. Mater. Technol., 1977, 99(2), p 133–137CrossRef

23.

I. Finnie, Some Observations on the Erosion of Ductile Metals, Wear, 1972, 19, p 81–90CrossRef

24.

H.C. Meng and K.C. Ludema, Wear Models and Predictive Equations: Their Form and Content, Wear, 1995, 181–183, p 443–457CrossRef

25.

M. Whittaker, Titanium in the Gas Turbine Engine, Advances in Gas Turbine Technology, Dr. Ernesto Benini, Ed., In Tech, 2011, https://doi.org/10.5772/21524

26.

C.C. Koch, Optimization of Strength and Ductility in Nanocrystalline and Ultrafine Grained Metals, Scr. Mater., 2003, 49, p 657–662CrossRef

27.

A.A. Hamed, W. Tabakoff, R.R. Rivir, K. Das, and P. Arora, Turbine Blade Surface Deterioration by Erosion, J. Turbomach., 2005, 127, p 445–452CrossRef

28.

A.V. Levy and G. Hickey, Liquid-Solid Particle Slurry Erosion of Steels, Wear, 1987, 117, p 129–146CrossRef

29.

D.G. Rickerby and N.H. Macmillan, The Erosion of Aluminum by Solid Particle Impingement at Normal Incidence, Wear, 1980, 60, p 369–382CrossRef

30.

H. Itoga, K. Tokaji, M. Nakajima, and H.-N. Ko, Effect of Surface Roughness on Step-Wise S-N Characteristics in High Strength Steel, Int. J. Fatigue, 2003, 25, p 379–385CrossRef

31.

J.T. Black and R.A. Kohser, DeGarmo’s Materials and Processes in Manufacturing, 11th ed., L. Ratts, Ed., Wiley, 2011

32.

W. Sage and G.P. Tilly, The Significance of Particle Size in Sand Erosion of Small Gas Turbines, J. R. Aero. Soc., 1969, 73, p 427–428

33.

E. Avcu, S. Fidan, Y. Yildiran, and T. Sınmazcelik, Solid Particle Erosion Behaviour of Ti6Al4V, Tribol. Mater. Surf. Interfaces, 2013, 7(4), p 201–210CrossRef

34.

G.V. Garkushin, O.N. Ignatova, G.I. Kanel, L.W. Meyer, and S.V. Razorenov, Submicrosecond Strength of Ultrafine-Grained Materials, Mechanics of Solids, 2010, 45(4), p 624–632CrossRef

35.

C.T. Wang, N. Gao, M.G. Gee, R.J.K. Wood, and T.G. Langdon, Tribology Testing of Ultrafine-Grained Ti Processed by High-Pressure Torsion with Subsequent Coating, J. Mater. Sci., 2013, 48(13), p 4742–4748CrossRef

36.

T. Mungole, P. Kumar, M. Kawasaki, and T.G. Langdon, The Contribution of Grain Boundary Sliding in Tensile Deformation of an Ultrafine-Grained Aluminum Alloy Having High Strength and High Ductility, J. Mater. Sci., 2015, 50, p 3549–3561CrossRef

Title: The Effect of Grain Refinement on Solid Particle Erosion of Grade 5 Ti Alloy
Authors: N. A. Kazarinov
A. D. Evstifeev
Y. V. Petrov
S. A. Atroshenko
R. R. Valiev
Publication date: 19-04-2018
Publisher: Springer US
Published in: Journal of Materials Engineering and Performance / Issue 6/2018
Print ISSN: 1059-9495
Electronic ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-018-3332-8

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 6/2018

Prediction and Computation of Corrosion Rates of A36 Mild Steel in Oilfield Seawater

Effect of Pore Size, Morphology and Orientation on the Bulk Stiffness of a Porous Ti35Nb4Sn Alloy

Effect of Multiple Local Repairs on Microstructure and Mechanical Properties of T24 Steel Welded Joint

Effect of Heat Exposure on the Fatigue Properties of AA7050 Friction Stir Welds

An Investigation into the Effects of Process Conditions on the Tribological Performance of Pack Carburized Titanium with Limited Oxygen Diffusion

Analytical Modeling of Triple-Metal Hetero-Dielectric DG SON TFET

Premium Partners