Top

The International Journal of Advanced Manufacturing Technology

Published in:

09-06-2021 | ORIGINAL ARTICLE

Comparative analysis of the machining temperatures of an end mill and a novel tool in the orbital drilling of CFRP composites

Authors: Linghao Kong, Dong Gao, Yong Lu

Published in: The International Journal of Advanced Manufacturing Technology | Issue 11-12/2021

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

The defects and rejections caused by the combined action of thrust force and cutting heat impede the wide application of carbon fiber-reinforced plastic (CFRP). To study the cutting temperature of two kinds of tools in the orbital drilling of CFRPs, a cutting force model and a heat transfer model were proposed in this research. The three-dimensional heat transfer equation in polar coordinates was established to predict the temperature inside the workpiece and was solved with the finite difference approach. The cutting edge on the bottom of the tool is the main cause of the thrust force, and due to the accumulation of cutting heat, the processing temperature at the exit is higher. The results show that the predictions of the model coincide with the experimental data and that the model can predict the temperature field inside the workpiece in the process of orbital drilling. The novel orbital drilling and reaming tool can effectively reduce the processing temperature of orbital drilling.

previous article Comparative study on cutting performance of conventional and ultrasonic-assisted bi-directional helical milling of CFRP

next article Modeling and prediction of cutting temperature in the machining of H13 hard steel of multi-layer coated cutting tools

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

Gao YF, Xiong J, Xiao JH, Lu D (2019) A tilted orbital grinding technique for hole-making of CFRP composite laminates. Int J Adv Manuf Technol 104(1-4):661–673. https://doi.org/10.1007/s00170-019-03904-xCrossRef

Wang CY, Chen YH, An QL, Cai XJ, Ming WW, Chen M (2015) Drilling temperature and hole quality in drilling of CFRP/aluminum stacks using diamond coated drill. Int J Precis Eng Manuf 16(8):1689–1697. https://doi.org/10.1007/s12541-015-0222-yCrossRef

Ben W, Hang G, Quan W, Maoqing W, Songpeng Z (2012) Influence of cutting heat on quality of drilling of carbon/epoxy composites. Mater Manuf Process 27(9):968–972. https://doi.org/10.1080/10426914.2011.610079CrossRef

Bonnet C, Poulachon G, Rech J, Girard Y, Costes JP (2015) CFRP drilling: Fundamental study of local feed force and consequences on hole exit damage. Int J Mach Tool Manu 94:57–64. https://doi.org/10.1016/j.ijmachtools.2015.04.006CrossRef

Feito N, Diaz-Alvarez J, Lopez-Puente J, Miguelez MH (2018) Experimental and numerical analysis of step drill bit performance when drilling woven CFRPs. Compos Struct 184:1147–1155. https://doi.org/10.1016/j.compstruct.2017.10.061CrossRef

Durao LMP, Goncalves DJS, Tavares JMRS, de Albuquerque VHC, Vieira AA, Marques AT (2010) Drilling tool geometry evaluation for reinforced composite laminates. Compos Struct 92(7):1545–1550. https://doi.org/10.1016/j.compstruct.2009.10.035CrossRef

Su F, Zheng L, Sun FJ, Wang ZH, Deng ZH, Qiu XY (2018) Novel drill bit based on the step-control scheme for reducing the CFRP delamination. J Mater Process Technol 262:157–167. https://doi.org/10.1016/j.jmatprotec.2018.06.037CrossRef

Isbilir O, Ghassemieh E (2013) Numerical investigation of the effects of drill geometry on drilling induced delamination of carbon fiber reinforced composites. Compos Struct 105:126–133. https://doi.org/10.1016/j.compstruct.2013.04.026CrossRef

Qiu XY, Li PN, Niu QL, Chen AH, Ouyang PR, Li CP, Ko TJ (2018) Influence of machining parameters and tool structure on cutting force and hole wall damage in drilling CFRP with stepped drills. Int J Adv Manuf Technol 97(1-4):857–865. https://doi.org/10.1007/s00170-018-1981-2CrossRef

10.

Butler-Smith PW, Axinte DA, Dame M, Kennedy AR, Harper LT, Bucourt JF, Ragueneau R (2015) A study of an improved cutting mechanism of composite materials using novel design of diamond micro-core drills. Int J Mach Tool Manu 88:175–183. https://doi.org/10.1016/j.ijmachtools.2014.10.002CrossRef

11.

Hocheng H, Tsao CC (2005) The path towards delamination-free drilling of composite materials. J Mater Process Technol 167(2-3):251–264. https://doi.org/10.1016/j.jmatprotec.2005.06.039CrossRef

12.

Qiu XY, Li PN, Li CP, Niu QL, Chen AH, Ouyang PR, Ko TJ (2018) Study on chisel edge drilling behavior and step drill structure on delamination in drilling CFRP. Compos Struct 203:404–413. https://doi.org/10.1016/j.compstruct.2018.07.007CrossRef

13.

Tsao CC (2008) Experimental study of drilling composite materials with step-core drill. Mater Des 29(9):1740–1744. https://doi.org/10.1016/j.matdes.2008.03.022CrossRef

14.

Zimmermann M, Heberger L, Schneider F, Effgen C, Aurich JC (2016) Investigation of chip formation and workpiece load when machining carbon-fiber-reinforced-polymer (CFRP). 16th Machining Innovations Conference for Aerospace Industry - Mic 2016 6:124-131. doi:https://doi.org/10.1016/j.promfg.2016.11.016

15.

Shyha IS, Aspinwall DK, Soo SL, Bradley S (2009) Drill geometry and operating effects when cutting small diameter holes in CFRP. Int J Mach Tool Manu 49(12-13):1008–1014. https://doi.org/10.1016/j.ijmachtools.2009.05.009CrossRef

16.

Iliescu D, Gehin D, Gutierrez ME, Girot F (2010) Modeling and tool wear in drilling of CFRP. Int J Mach Tool Manu 50(2):204–213. https://doi.org/10.1016/j.ijmachtools.2009.10.004CrossRef

17.

Pereira RBD, Brandao LC, de Paiva AP, Ferreira JR, Davim JP (2017) A review of helical milling process. Int J Mach Tool Manu 120:27–48. https://doi.org/10.1016/j.ijmachtools.2017.05.002CrossRef

18.

Brinksmeier E, Fangmann S, Meyer I (2008) Orbital drilling kinematics. Prod Eng 2(3):277–283. https://doi.org/10.1007/s11740-008-0111-7CrossRef

19.

Geier N, Davim JP, Szalay T (2019) Advanced cutting tools and technologies for drilling carbon fibre reinforced polymer (CFRP) composites: a review. Compos Part a-Appl S 125:105552. https://doi.org/10.1016/j.compositesa.2019.105552CrossRef

20.

Pereszlai C, Geier N (2020) Comparative analysis of wobble milling, helical milling and conventional drilling of CFRPs. Int J Adv Manuf Technol 106(9-10):3913–3930. https://doi.org/10.1007/s00170-019-04842-4CrossRef

21.

Xu WX, Zhang LC (2014) On the mechanics and material removal mechanisms of vibration-assisted cutting of unidirectional fibre-reinforced polymer composites. Int J Mach Tool Manu 80-81:1–10. https://doi.org/10.1016/j.ijmachtools.2014.02.004CrossRef

22.

Alberdi A, Suarez A, Artaza T, Escobar-Palafox GA, Ridgway K (2013) Composite Cutting with abrasive water jet. Manuf Eng Soc Int Conf, (Mesic 2013) 63:421–429. https://doi.org/10.1016/j.proeng.2013.08.217CrossRef

23.

Herzog D, Jaeschke P, Meier O, Haferkamp H (2008) Investigations on the thermal effect caused by laser cutting with respect to static strength of CFRP. Int J Mach Tool Manu 48(12-13):1464–1473. https://doi.org/10.1016/j.ijmachtools.2008.04.007CrossRef

24.

Teicher U, Muller S, Munzner J, Nestler A (2013) Micro-EDM of carbon fibre-reinforced plastics. Proc Seventeenth Cirp Conf Electro Physical Chem Mach (Isem) 6:320–325. https://doi.org/10.1016/j.procir.2013.03.092CrossRef

25.

Wang Q, Wu Y, Bitou T, Nomura M, Fujii T (2017) Proposal of a tilted helical milling technique for high quality hole drilling of CFRP: kinetic analysis of hole formation and material removal. Int J Adv Manuf Technol 94(9-12):4221–4235. https://doi.org/10.1007/s00170-017-1106-3CrossRef

26.

Voss R, Henerichs M, Kuster F (2016) Comparison of conventional drilling and orbital drilling in machining carbon fibre reinforced plastics (CFRP). Cirp Ann-Manuf Technol 65(1):137–140. https://doi.org/10.1016/j.cirp.2016.04.001CrossRef

27.

Wang GD, Kirwa MS, Li N (2018) Experimental studies on a two-step technique to reduce delamination damage during milling of large diameter holes in CFRP/Al stack. Compos Struct 188:330–339. https://doi.org/10.1016/j.compstruct.2018.01.039CrossRef

28.

Taylor FW (1907) The art of cutting metals. Sci Am 63(1618supp):25929–25931CrossRef

29.

Komanduri R, Hou ZB (2000) Thermal modeling of the metal cutting process - Part I - temperature rise distribution due to shear plane heat source. Int J Mech Sci 42(9):1715–1752. https://doi.org/10.1016/S0020-7403(99)00070-3CrossRefMATH

30.

Komanduri R, Hou ZB (2001) Thermal modeling of the metal cutting process — Part II: temperature rise distribution due to frictional heat source at the tool–chip interface. Int J Mech Sci 43(1):57–88. https://doi.org/10.1016/s0020-7403(99)00104-6CrossRefMATH

31.

Komanduri R, Hou ZB (2001) Thermal modeling of the metal cutting process — Part III: temperature rise distribution due to the combined effects of shear plane heat source and the tool–chip interface frictional heat source. Int J Mech Sci 43(1):89–107. https://doi.org/10.1016/s0020-7403(99)00105-8CrossRefMATH

32.

Lin S, Peng FY, Wen J, Liu YZ, Yan R (2013) An investigation of workpiece temperature variation in end milling considering flank rubbing effect. Int J Mach Tool Manu 73:71–86. https://doi.org/10.1016/j.ijmachtools.2013.05.010CrossRef

33.

Huang Y, Liang SY (2005) Cutting temperature modeling based on non-uniform heat intensity and partition ratio. Mach Sci Technol 9(3):301–323. https://doi.org/10.1080/10910340500196421CrossRef

34.

Bäker M (2006) Finite element simulation of high-speed cutting forces. J Mater Process Technol 176(1-3):117–126. https://doi.org/10.1016/j.jmatprotec.2006.02.019CrossRef

35.

Li R, Shih AJ (2005) Finite element modeling of 3D turning of titanium. Int J Adv Manuf Technol 29(3-4):253–261. https://doi.org/10.1007/s00170-005-2511-6CrossRef

36.

Umbrello D, M’Saoubi R, Outeiro JC (2007) The influence of Johnson–Cook material constants on finite element simulation of machining of AISI 316L steel. Int J Mach Tools Manuf 47(3-4):462–470. https://doi.org/10.1016/j.ijmachtools.2006.06.006CrossRef

37.

Dutt RP, Brewer RC (1965) On the theoretical determination of the temperature field in orthogonal machining. Int J Prod Res 4(2):91–114. https://doi.org/10.1080/00207546508919968CrossRef

38.

Lazoglu I, Altintas Y (2002) Prediction of tool and chip temperature in continuous and interrupted machining. Int J Mach Tool Manu 42(9):1011–1022. https://doi.org/10.1016/S0890-6955(02)00039-1CrossRef

39.

Liu J, Ren CZ, Qin XD, Li H (2014) Prediction of heat transfer process in helical milling. Int J Adv Manuf Technol 72(5-8):693–705. https://doi.org/10.1007/s00170-014-5662-5CrossRef

40.

Liu J, Chen G, Ji CH, Qin XD, Li H, Ren CZ (2014) An investigation of workpiece temperature variation of helical milling for carbon fiber reinforced plastics (CFRP). Int J Mach Tool Manu 86:89–103. https://doi.org/10.1016/j.ijmachtools.2014.06.008CrossRef

41.

Zhang BY, Wang FJ, Wang XD, Li Y, Wang Q (2020) Optimized selection of process parameters based on reasonable control of axial force and hole-exit temperature in drilling of CFRP. Int J Adv Manuf Technol 110(3-4):797–812. https://doi.org/10.1007/s00170-020-05868-9CrossRef

42.

Sun Y, Sun J, Li J, Xiong Q (2013) An experimental investigation of the influence of cutting parameters on cutting temperature in milling Ti6Al4V by applying semi-artificial thermocouple. Int J Adv Manuf Technol 70(5-8):765–773. https://doi.org/10.1007/s00170-013-5294-1CrossRef

43.

Sheng J, Chiu Y-J, Lin B-J (2017) Determination of a coupling equation for milling parameters based on optimal cutting temperature. Int J Adv Manuf Technol 98(1-4):129–141. https://doi.org/10.1007/s00170-017-0542-4CrossRef

44.

Wang H, Sun J, Li J, Lu L, Li N (2015) Evaluation of cutting force and cutting temperature in milling carbon fiber-reinforced polymer composites. Int J Adv Manuf Technol 82(9-12):1517–1525. https://doi.org/10.1007/s00170-015-7479-2CrossRef

45.

Weinert K, Brinkel F, Kempmann C, Pantke K (2007) The dependency of material properties and process conditions on the cutting temperatures when drilling polymers. Prod Eng 1(4):381–387. https://doi.org/10.1007/s11740-007-0015-yCrossRef

46.

Guimarães B, Fernandes CM, Figueiredo D, Cerqueira MF, Carvalho O, Silva FS, Miranda G (2020) A novel approach to reduce in-service temperature in WC-Co cutting tools. Ceram Int 46(3):3002–3008. https://doi.org/10.1016/j.ceramint.2019.09.299CrossRef

47.

Sasahara H, Satake K, Takahashi W, Goto M, Yamamoto H (2017) The effect of oil mist supply on cutting point temperature and tool wear in driven rotary cutting. Precis Eng 48:158–163. https://doi.org/10.1016/j.precisioneng.2016.11.016CrossRef

48.

Merino-Perez JL, Royer R, Merson E, Lockwood A, Ayvar-Soberanis S, Marshall MB (2016) Influence of workpiece constituents and cutting speed on the cutting forces developed in the conventional drilling of CFRP composites. Compos Struct 140:621–629. https://doi.org/10.1016/j.compstruct.2016.01.008CrossRef

49.

Yashiro T, Ogawa T, Sasahara H (2013) Temperature measurement of cutting tool and machined surface layer in milling of CFRP. Int J Mach Tool Manu 70:63–69. https://doi.org/10.1016/j.ijmachtools.2013.03.009CrossRef

50.

Chen T, Ye ML, Deng Y, Liu SL (2018) Study of temperature field for UVAG of CFRP based on FBG. Int J Adv Manuf Technol 96(1-4):765–773. https://doi.org/10.1007/s00170-018-1642-5CrossRef

51.

Kong L, Gao D, Lu Y, Jiang Z (2020) Novel orbital drilling and reaming tool for machining holes in carbon fiber–reinforced plastic (CFRP) composite laminates. Int J Adv Manuf Technol 110(3-4):977–988. https://doi.org/10.1007/s00170-020-05928-0CrossRef

52.

Zhirong L (2017) Research on bone cutting and a novel tool development. Dissertation, Harbin Institute of Technology,

53.

Shaw MC, Cookson JO (1985) Metal cutting principles. Tribol Int 18(1):55–55CrossRef

54.

Berliner EM, Krainov VP (1991) Analytic calculations of the temperature-field and heat flows on the tool surface in metal-cutting due to sliding friction. Wear 143(2):379–395. https://doi.org/10.1016/0043-1648(91)90108-7CrossRef

55.

Budak E, Altintas Y, Armarego EJA (1996) Prediction of milling force coefficients from orthogonal cutting data. J Manuf Sci E-T Asme 118(2):216–224. https://doi.org/10.1115/1.2831014CrossRef

56.

Denkena N, Rehe, & Dege. (2011) Process force prediction in orbital drilling of TiAl6V4. 9th International Conference on Advanced Manufacturing Systems and Technology

57.

Wang MH, Gao L, Zheng YH (2014) An examination of the fundamental mechanics of cutting force coefficients. Int J Mach Tool Manu 78:1–7. https://doi.org/10.1016/j.ijmachtools.2013.10.008CrossRef

58.

Haiyan W, Xuda Q (2015) A mechanistic model for cutting force in helical milling of carbon fiber-reinforced polymers. Int J Adv Manuf Technol 82(9-12):1485–1494. https://doi.org/10.1007/s00170-015-7460-0CrossRef

Title: Comparative analysis of the machining temperatures of an end mill and a novel tool in the orbital drilling of CFRP composites
Authors: Linghao Kong
Dong Gao
Yong Lu
Publication date: 09-06-2021
Publisher: Springer London
Published in: The International Journal of Advanced Manufacturing Technology / Issue 11-12/2021
Print ISSN: 0268-3768
Electronic ISSN: 1433-3015
DOI: https://doi.org/10.1007/s00170-021-07409-4

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 11-12/2021

Effect of the parametric optimization and heat-treatment on the 18Ni-300 maraging steel microstructural properties manufactured by directed energy deposition

Evaluation of MQL performances using various nanofluids in turning of AISI 304 stainless steel

The effect of porosity on the mechanical properties of Ti-6Al-4V components manufactured by high-power selective laser melting

Effects of constricted arc on the shaping of additively manufactured parts by cold metal transfer arc

A study of modeling assumptions and adaptive remeshing for thermomechanical finite element modeling of the LPBF process

Rake angle effects on ultrasonic-assisted edge trimming of multidirectional CFRP laminates

Premium Partners