Top

Arabian Journal for Science and Engineering

Published in:

29-09-2021 | Research Article-Mechanical Engineering

Creep Analysis of Plastically Deformed Shrink-Fitted Joints

Authors: Amal Mouâa, Nor Eddine Laghzale, Abdel-Hakim Bouzid

Published in: Arabian Journal for Science and Engineering | Issue 7/2022

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

Shrink fitted joints can fail due to creep, especially when they are subjected to high temperatures. Creep strain can reduce the contact stress produced by the interference fit and loosen the fit joint. This phenomenon is very common in rotating turbines, gears, bearings, and rings, when these components are exposed to elevated temperatures. This paper presents an analytical model that describes stresses and strain in a plastically deformed shrink-fitted assembly, consisting of a solid shaft and a cylindrical hub under creep. The developed model is used to estimate the distribution of stresses and creep strain in a plastically deformed interference fit and their change over time, as creep takes place. It also predicts the change in the contact pressure and the variation of radial and circumferential stresses for different hub radii over time. The creep analysis uses Norton’s law. The results of the analytical model were graphically compared to those obtained by the finite element method (FEM), using a general-purpose FEM software.

previous article Multi-scale Modeling of Polymeric Composites Including Nanoporous Fillers of Milled Anodic Alumina

next article Intelligent Computing with Levenberg–Marquardt Backpropagation Neural Networks for Third-Grade Nanofluid Over a Stretched Sheet with Convective Conditions

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

Sim, R.G.; Penny, R.K.: Plane strain creep behavior of thick-walled cylinders. Int. J. Mech. Sci. 13, 987–1009 (1971)CrossRef

Eshati, S.; Abu, A.; Laskaridis, P.; Khan, F.: Influence of water-air ratio on the heat transfer and creep life of a high pressure gas turbine blade. Appl. Therm. Eng. 60(1–2), 335–347 (2013)CrossRef

Mailyan, L.; Chepurnenko, A.; Ivanov, A.: Calculation of prestressed concrete cylinder considering creep of concrete. Procedia Eng. 165, 1853–1857 (2016)CrossRef

Khanna, K.; Gupta, V.K.; Nigam, S.P.: Creep analysis in functionally graded rotating disc using Tresca criterion and comparison with Von-Mises criterion. Mater. Today Proc. 4(2), 2431–2438 (2017)CrossRef

Du, X.; Zhang, J.; Liu, Y.: Plastic failure analysis of defective pipes with creep damage under multi-loading systems. Int. J. Mech. Sci. 128–129, 428–444 (2017)CrossRef

K. S. Raghavan: Investigations into creep behavior of gas turbine component assemblies. In: Proceeding of the ASME 2012 Gas Turbine India Conference, 2012, pp. 1–9.

Cyr, N.A.; Teter, R.D.: Finite element elastic-plastic-creep analysis of two-dimensional continuum with temperature dependent material properties. Comput. Struct. 3(4), 849–863 (1973)CrossRef

Kocks, U.F.: Laws for work-hardening and low-temprature creep. J. Eng. Mater. Technol. 98, 76–85 (1976)CrossRef

Voce, E.: The relationship between stress and strain for homogeneous deformation. J. Inst. Met. 74, 537–562 (1948)

10.

Jahed, H.; Dubey, R.N.: An axisymmetric method of elastic-plastic analysis capable of predicting residual stress field. J. Press. Vessel Technol. 119(3), 264–273 (1997)CrossRef

11.

Jahed, H.; Bidabadi, J.: An axisymmetric method of creep analysis for primary and secondary creep. Int. J. Press. Vessel. Pip. 80(9), 597–606 (2003)CrossRef

12.

Laghzale, N.E.; Bouzid, A.H.: Effect of creep on the residual stresses in tube-to-tubesheet joints. J. Press. Vessel Technol. Trans. ASME 132(6), 0612101–0612106 (2010)CrossRef

13.

May, D.L.; Gordon, A.P.; Segletes, D.S.: The application of the Norton-Bailey law for creep prediction through power law regression. Struct. Dyn. (2013). https://doi.org/10.1115/GT2013-96008CrossRef

14.

Wong, E.H.; Mai, Y.W.: A unified equation for creep-fatigue. Int. J. Fatigue 68, 186–194 (2014)CrossRef

15.

Bose, T.; Rattan, M.: Effect of thermal gradation on steady state creep of functionally graded rotating disc. Eur. J. Mech. A/Solids 67, 169–176 (2017)MathSciNetCrossRef

16.

Esposito, L.; Bruno, M.; Bertocco, A.: Analytical formulation of the contact pressure evolution for interference joints under creep regime. Int. J. Press. Vessel. Pip. 185, 104126 (2020)CrossRef

17.

Borkowski, P.; Głowacki, D.; Nowakowska, A.; Pawlicki, J.; Zwoliński, J.: FE analysis of a steam turbine HP rotor blade stage concerning material effort, dynamic properties and creep damage assessment. Arch. Mech. Eng. 63(1), 163–185 (2016)CrossRef

18.

P. Tang, M. Wang, Z. Ling, N. Jin, and W. Guo,: Creep behavior and defect interference of volume defect under high temperature. In Volume 1B: Codes and Standards, (2016).

19.

Mouaa, A.; Laghzale, N.E.; Bouzid, A.-H.: Analytical modelling of interference fit joints with power law strain-hardening behavior. Int. Rev. Model. Simul. 14(1), 24 (2021)

20.

Laghzale, N.; Bouzid, A.: Analytical modelling of elastic-plastic interference fit joints. Int. Rev. Model. Simul. 9(3), 191 (2016)

21.

Burenin, A.A.; Dats, E.P.; Tkacheva, A.V.: On the modeling of the shrink fit technology. J. Appl. Ind. Math. 8(4), 493–499 (2014)MathSciNetCrossRef

22.

Callister, W.D.; Rethwisch, D.G.: Fundamentals of materials science and engineering: an integrated approach, 4th edn. Wiley, London (2012)

23.

William, J.; Callister, D.: Fundamentals of materials science and engineering: an interactive e-text, 5th edn., p. 441–468. Wiley, London (2000)

24.

Tahami, F.V.; Daei-Sorkhabi, A.H.; Biglari, F.R.: Creep constitutive equations for cold-drawn 304L stainless steel. Mater. Sci. Eng. A 527(18–19), 4993–4999 (2010)CrossRef

Title: Creep Analysis of Plastically Deformed Shrink-Fitted Joints
Authors: Amal Mouâa
Nor Eddine Laghzale
Abdel-Hakim Bouzid
Publication date: 29-09-2021
Publisher: Springer Berlin Heidelberg
Published in: Arabian Journal for Science and Engineering / Issue 7/2022
Print ISSN: 2193-567X
Electronic ISSN: 2191-4281
DOI: https://doi.org/10.1007/s13369-021-06192-4

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 7/2022

Thermal Analysis of Phase Changing Material in Heat Exchanger

Model for Analyzing the Critical Variables of an Industrial Process Using Fuzzy Inference System and Likert Scale

An Experimental Study and Joining Parameters Optimization of Friction Stir Weld Butt Joint by Taguchi Approach to Maximize the Mechanical Properties

An Analytical Model Including the Tip Loss Effects to Predict the Sectional Pressure Drag for a Wind Turbine Blade Oscillating in Pitch

Vibration Analysis-Based Fault Diagnosis of a Dynamically Loaded Bearing with Distributed Defect

A Novel Fluid–Structure Interaction (FSI) Modeling Approach to Predict the Temperature Distribution in Single-Point Cutting Tool for Condition Monitoring During Turning Process

Premium Partners