Top

Meccanica

Published in:

26-06-2019

Design of buckling constrained multiphase material structures using continuum topology optimization

Authors: Quoc Hoan Doan, Dongkyu Lee, Jaehong Lee, Joowon Kang

Published in: Meccanica | Issue 8/2019

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

This study contributes to a possibility of evaluating composite structures configuration such as steel and concrete using buckling and volume constraints based on multi-material topology optimization. A Jacobi active-phase algorithm is used to generate multiphase topology optimization. It provides a rational solution appropriated to the topology optimizer, Method of Moving Asymptotes due to the conflict in updating the design variables. A modified material interpolation scheme solving spurious buckling modes problem which occurs in the multi-material topology optimization process is given and discussed. An investigation of buckling constraint parameter is described. It allows a single-objective minimum compliance topology optimization to obtain two objectives of maximizing both structure stiffness and first buckling load factor. The optimal changing topologies of single material structure and multi-material structure corresponding to different buckling constraints are presented. Numerical examples of compression-only structures and compression-tension structures considering structural instability are performed using both single material and multiple materials to verify the efficiency and superiority of the present method.

previous article Impact of the slip condition on the resonance of a film flow over an inclined slippery topography plate

next article Adaptive back stepping fast terminal sliding mode control of robot manipulators actuated by pneumatic artificial muscles: continuum modelling, dynamic formulation and controller design

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

Lee D, Shin S, Lee J, Lee K (2015) Layout evaluation of building outrigger truss by using material topology optimization. Steel Compos Struct 19:263–275CrossRef

Rozvany GIN (1996) Difficulties in truss topology optimization with stress, local buckling and system stability constraints. Struct Optim 11:213–217. https://doi.org/10.1007/BF01197036 CrossRef

Neves MM, Rodrigues H, Guedes JM (1995) Generalized topology design of structures with a buckling load criterion. Struct Optim 10:71–78. https://doi.org/10.1007/BF01743533 CrossRef

Foldager JP, Hansen JS, Olhoff N (2001) Optimization of the buckling load for composite structures taking thermal effects into account. Struct Multidiscip Optim 21:14–31. https://doi.org/10.1007/s001580050164 CrossRef

Du J, Olhoff N (2007) Topological design of freely vibrating continuum structures for maximum values of simple and multiple eigenfrequencies and frequency gaps. Struct Multidiscip Optim 34:91–110. https://doi.org/10.1007/s00158-007-0101-y MathSciNetCrossRefMATH

Setoodeh S, Abdalla MM, IJsselmuiden ST ST, Gürdal Z (2009) Design of variable-stiffness composite panels for maximum buckling load. Compos Struct 87:109–117. https://doi.org/10.1016/j.compstruct.2008.01.008 CrossRef

Lindgaard E, Dahl J (2013) On compliance and buckling objective functions in topology optimization of snap-through problems. Struct Multidiscip Optim 47:409–421. https://doi.org/10.1007/s00158-012-0832-2 MathSciNetCrossRefMATH

Luo Q, Tong L (2015) Structural topology optimization for maximum linear buckling loads by using a moving iso-surface threshold method. Struct Multidiscip Optim 52:71–90. https://doi.org/10.1007/s00158-015-1286-0 MathSciNetCrossRef

Lund E (2009) Buckling topology optimization of laminated multi-material composite shell structures. Compos Struct 91:158–167. https://doi.org/10.1016/j.compstruct.2009.04.046 CrossRef

10.

Manickarajah D (1998) Optimum design of structures with stability constraints using the evolutionary optimisation method. Victoria University of Technology

11.

Rahmatalla S, Swan CC (2003) Continuum topology optimization of buckling-sensitive structures. AIAA J 41:1180–1189. https://doi.org/10.2514/2.2062 ADSCrossRef

12.

Dunning PD, Ovtchinnikov E, Scott J, Kim HA (2016) Level-set topology optimization with many linear buckling constraints using an efficient and robust eigensolver. Int J Numer Methods Eng 107:1029–1053. https://doi.org/10.1002/nme.5203 MathSciNetCrossRefMATH

13.

Bojczuk D, Mróz Z (1999) Optimal topology and configuration design of trusses with stress and buckling constraints. Struct Optim 17:25–35. https://doi.org/10.1007/BF01197710 CrossRef

14.

Pedersen NL, Nielsen AK (2003) Optimization of practical trusses with constraints on eigenfrequencies, displacements, stresses, and buckling. Struct Multidiscip Optim 25:436–445. https://doi.org/10.1007/s00158-003-0294-7 CrossRef

15.

Guo X, Cheng GD, Olhoff N (2005) Optimum design of truss topology under buckling constraints. Struct Multidiscip Optim 30:169–180. https://doi.org/10.1007/s00158-004-0511-z CrossRef

16.

Qiao Shengfang, Xiaolei Han KZ, Ji J (2016) Seismic analysis of steel structure with brace configuration using topology optimization. Steel Compos Struct 21:501–515. https://doi.org/10.12989/scs.2016.21.3.501 CrossRef

17.

Gao X, Ma H (2015) Topology optimization of continuum structures under buckling constraints. Comput Struct 157:142–152. https://doi.org/10.1016/j.compstruc.2015.05.020 CrossRef

18.

Singh R, Kumar R, Farina I et al (2019) Multi-material additive manufacturing of sustainable innovative materials and structures. Polymers 11:62CrossRef

19.

Banh TT, Lee D (2018) Multi-material topology optimization design for continuum structures with crack patterns. Compos Struct 186:193–209. https://doi.org/10.1016/j.compstruct.2017.11.088 CrossRef

20.

Banh TT, Lee D (2018) Multi-material topology optimization of Reissner-Mindlin plates using MITC4. Steel Compos Struct 27:27–33. https://doi.org/10.12989/scs.2018.27.1.027

21.

Blasques JP, Stolpe M (2012) Multi-material topology optimization of laminated composite beam cross sections. Compos Struct 94:3278–3289. https://doi.org/10.1016/j.compstruct.2012.05.002 CrossRef

22.

Blasques JP (2014) Multi-material topology optimization of laminated composite beams with eigenfrequency constraints. Compos Struct 111:45–55. https://doi.org/10.1016/j.compstruct.2013.12.021 CrossRef

23.

Wang MY, Zhou S (2004) Synthesis of shape and topology of multi-material structures with a phase-field method. J Comput Mater Des 11:117–138. https://doi.org/10.1007/s10820-005-3169-y CrossRef

24.

Zhou S, Wang MY (2006) 3D multi-material structural topology optimization with the generalized Cahn-Hilliard equations. Comput Model Eng Sci 16:83–101

25.

Sigmund O, Torquato S (1997) Design of materials with extreme thermal expansion using a three-phase topology optimization method. J Mech Phys Solids 45:1037–1067. https://doi.org/10.1016/S0022-5096(96)00114-7 ADSMathSciNetCrossRef

26.

Tavakoli R, Mohseni SM (2014) Alternating active-phase algorithm for multimaterial topology optimization problems: a 115-line MATLAB implementation. Struct Multidiscip Optim 49:621–642. https://doi.org/10.1007/s00158-013-0999-1 MathSciNetCrossRef

27.

Guo X, Zhang W, Zhong W (2014) Stress-related topology optimization of continuum structures involving multi-phase materials. Comput Methods Appl Mech Eng 268:632–655. https://doi.org/10.1016/j.cma.2013.10.003 ADSMathSciNetCrossRefMATH

28.

Tavakoli R (2014) Multimaterial topology optimization by volume constrained Allen-Cahn system and regularized projected steepest descent method. Comput Methods Appl Mech Eng 276:534–565. https://doi.org/10.1016/j.cma.2014.04.005 ADSMathSciNetCrossRefMATH

29.

Park J, Sutradhar A (2015) A multi-resolution method for 3D multi-material topology optimization. Comput Methods Appl Mech Eng 285:571–586. https://doi.org/10.1016/j.cma.2014.10.011 ADSMathSciNetCrossRefMATH

30.

Liu P, Luo Y, Kang Z (2016) Multi-material topology optimization considering interface behavior via XFEM and level set method. Comput Methods Appl Mech Eng 308:113–133. https://doi.org/10.1016/j.cma.2016.05.016 ADSMathSciNetCrossRef

31.

Da DC, Cui XY, Long K, Li GY (2017) Concurrent topological design of composite structures and the underlying multi-phase materials. Comput Struct 179:1–14. https://doi.org/10.1016/j.compstruc.2016.10.006 CrossRef

32.

Neves MM, Sigmund O, Bendsøe MP (2002) Topology optimization of periodic microstructures with a penalization of highly localized buckling modes. Int J Numer Methods Eng 54:809–834. https://doi.org/10.1002/nme.449 MathSciNetCrossRefMATH

33.

Xingjun X, Haitao M (2014) A new method for dealing with pseudo modes in topology optimization of continua for free vibration. Chin J Theor Appl Mech 46:739–746

34.

Pedersen NL (2000) Maximization of eigenvalues using topology optimization. Struct Multidiscip Optim 20:2–11. https://doi.org/10.1007/s001580050130 CrossRef

35.

Bendsoe MP, Sigmund O (2004) Topology optimization: theory, methods, and applications, 2nd edn. Springer, BerlinCrossRefMATH

36.

Zhou S, Wang MY (2006) Multimaterial structural topology optimization with a generalized Cahn-Hilliard model of multiphase transition. Struct Multidiscip Optim 33:89–111. https://doi.org/10.1007/s00158-006-0035-9 MathSciNetCrossRefMATH

37.

Svanberg K (1987) The method of moving asymptotes—a new method for structural optimization. Int J Numer Methods Eng 24:359–373. https://doi.org/10.1002/nme.1620240207 MathSciNetCrossRefMATH

38.

Mróz Z, Haftka RT (1988) Sensitivity of buckling loads and vibration frequencies of plates. In: Elishakoff I, Arbocz J, Babcock CD, Libai A (eds) Buckling of structures. Elsevier, Amsterdam, pp 255–266CrossRef

39.

Kleiber M, Hien TD, Postek E (1994) Incremental finite element sensitivity analysis for non-linear mechanics applications. Int J Numer Methods Eng 37:3291–3308. https://doi.org/10.1002/nme.1620371906 CrossRefMATH

40.

Kleiber M, Hien TD (1997) Parameter sensitivity of inelastic buckling and post-buckling response. Comput Methods Appl Mech Eng 145:239–262. https://doi.org/10.1016/S0045-7825(96)01212-1 ADSCrossRefMATH

41.

Seyranian AP, Lund E, Olhoff N (1994) Multiple eigenvalues in structural optimization problems. Struct Optim 8:207–227. https://doi.org/10.1007/BF01742705 CrossRef

42.

Jensen JS, Pedersen NL (2006) On maximal eigenfrequency separation in two-material structures: the 1D and 2D scalar cases. J Sound Vib 289:967–986. https://doi.org/10.1016/j.jsv.2005.03.028 ADSCrossRef

43.

Gravesen J, Evgrafov A, Nguyen DM (2011) On the sensitivities of multiple eigenvalues. Struct Multidiscip Optim 44:583–587. https://doi.org/10.1007/s00158-011-0644-9 MathSciNetCrossRefMATH

44.

Sigmund O (1997) On the design of compliant mechanisms using topology optimization. Mech Struct Mach 25:493–524. https://doi.org/10.1080/08905459708945415 CrossRef

45.

Sigmund O (2007) Morphology-based black and white filters for topology optimization. Struct Multidiscip Optim 33:401–424. https://doi.org/10.1007/s00158-006-0087-x CrossRef

46.

Andreassen E, Clausen A, Schevenels M et al (2011) Efficient topology optimization in MATLAB using 88 lines of code. Struct Multidiscip Optim 43:1–16. https://doi.org/10.1007/s00158-010-0594-7 CrossRefMATH

47.

Zhou M (2004) Topology optimization for shell structures with linear buckling responses. Tsinghua University Press & Springer, Beijing

48.

Doan QH, Lee D (2017) Optimum topology design of multi-material structures with non-spurious buckling constraints. Adv Eng Softw 114:110–120. https://doi.org/10.1016/j.advengsoft.2017.06.002 CrossRef

49.

Plank H (2002) Overmolding-stack-mold technology an innovative concept in multi-component injection molding

50.

Goodship V, Love JC (2002) Multi-material injection moulding. Rapra Technology

51.

Banerjee AG, Li X, Fowler G, Gupta SK (2007) Incorporating manufacturability considerations during design of injection molded multi-material objects. Res Eng Des 17:207–231. https://doi.org/10.1007/s00163-007-0027-9 CrossRef

52.

Ji Y, Chen L, Chen L-Q (2018) Chapter 6—understanding microstructure evolution during additive manufacturing of metallic alloys using phase-field modeling. In: Gouge M, Michaleris P (eds) Thermo-mechanical modeling of additive manufacturing. Butterworth-Heinemann, Oxford, pp 93–116CrossRef

53.

Obielodan JO, Ceylan A, Murr LE, Stucker BE (2010) Multi-material bonding in ultrasonic consolidation. Rapid Prototyp J 16:180–188. https://doi.org/10.1108/13552541011034843 CrossRef

54.

Yang Q, Zhang P, Cheng L et al (2016) Finite element modeling and validation of thermomechanical behavior of Ti–6Al–4 V in directed energy deposition additive manufacturing. Addit Manuf 12:169–177. https://doi.org/10.1016/j.addma.2016.06.012 CrossRef

55.

Vaezi M, Chianrabutra S, Mellor B, Yang S (2013) Multiple material additive manufacturing—part 1: a review. Virtual Phys Prototyp 8:19–50. https://doi.org/10.1080/17452759.2013.778175 CrossRef

56.

Frazier WE (2014) Metal additive manufacturing: a review. J Mater Eng Perform 23:1917–1928. https://doi.org/10.1007/s11665-014-0958-z CrossRef

57.

Gouker RM, Gupta SK, Bruck HA, Holzschuh T (2006) Manufacturing of multi-material compliant mechanisms using multi-material molding. Int J Adv Manuf Technol 30:1049–1075. https://doi.org/10.1007/s00170-005-0152-4 CrossRef

58.

Bandyopadhyay A, Heer B (2018) Additive manufacturing of multi-material structures. Mater Sci Eng R Rep 129:1–16. https://doi.org/10.1016/j.mser.2018.04.001 CrossRef

59.

Huang SH, Liu P, Mokasdar A, Hou L (2013) Additive manufacturing and its societal impact: a literature review. Int J Adv Manuf Technol 67:1191–1203. https://doi.org/10.1007/s00170-012-4558-5 CrossRef

Title: Design of buckling constrained multiphase material structures using continuum topology optimization
Authors: Quoc Hoan Doan
Dongkyu Lee
Jaehong Lee
Joowon Kang
Publication date: 26-06-2019
Publisher: Springer Netherlands
Published in: Meccanica / Issue 8/2019
Print ISSN: 0025-6455
Electronic ISSN: 1572-9648
DOI: https://doi.org/10.1007/s11012-019-01009-z

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 8/2019

Adaptive back stepping fast terminal sliding mode control of robot manipulators actuated by pneumatic artificial muscles: continuum modelling, dynamic formulation and controller design

Dynamics of an electrified confined planar jet in a zero gravity environment

Vibrational analysis for surge precursor definition in gas turbines

Numerical and experimental study on mixing performance of a novel electro-osmotic micro-mixer

Fragmentation model of a rapidly expanding ring with arbitrary cross-section

Indentation on a one-dimensional hexagonal quasi-crystal half-space by an elliptic indenter

Premium Partners