Top

Journal of Materials Engineering and Performance

Published in:

01-10-2013

Evaluation of Hard Coating Performance in Drilling Compacted Graphite Iron (CGI)

Authors: José M. F. de Paiva Jr., Fred L. Amorim, P. Soares, Ricardo D. Torres

Published in: Journal of Materials Engineering and Performance | Issue 10/2013

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

The aim of this investigation was to compare the performance of the following commercial coatings system, TiAlN/TiN, AlCrN, and TiSiN/AlCrN, deposited in cemented carbide tools in drilling compact graphite iron (CGI). The drilling tests were conducted adopting two cutting speeds: 80 or 150 m/min. For each test condition, the tool flank wear, the machining feed force, and the circularity and the roughness of the resulting drilled hole were determined. At the cutting speed of 80 m/min, the results revealed that the tool life, in terms of flank wear, was improved for the Cr-based coatings, while the multilayered coatings presented a better performance at the cutting speed of 150 m/min. It was also found that feed force is substantially increased when drilling at a cutting speed of 150 m/min. The holes drilled with the TiSiN/AlCrN at a cutting speed of 150 m/min showed the best circularity. The drill roughness is directly influenced by the coating system wear and iron adhesion. Consequently, it was found that the lowest holes’ roughness was obtained with TiSiN/AlCrN at 80 m/min.

previous article Biocompatibly Coated 304 Stainless Steel as Superior Corrosion-Resistant Implant Material to 316L Steel

next article Fracture Toughness and Adhesion of Transparent Al:ZnO Films Deposited on Glass Substrates

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

H.K. Toenshoff, W. Spintig, W. Koenig, and A. Neisses, Machining of Holes Developments in Drilling Technology, Ann. CIRP, 1994, 43(2), p 551CrossRef

M.B. da Silva, V.T.G. Naves, J.D.B. Melo, C.L.F. de Andrade, and W.L. Guesser, Analysis of Wear of Cemented Carbide Cutting Tools During Milling Operation of Gray Iron and Compacted Graphite Iron, Wear, 2011, 271, p 2426–2432CrossRef

M. Heck, H.M. Ortner, S. Flege, U. Reuter, and W. Ensinger, Analytical Investigations Concerning the Wear Behaviour of Cutting Tools Used for the Machining of Compacted Graphite Iron and Grey Cast Iron, Int. J. Refract. Met. Hard. Mater., 2008, 26, p 197–206CrossRef

F. Mocellin, E. Melleras, W.L. Guesser, and L. Boehs, Study of the Machinability of Compacted Graphite Iron for Drilling Process, J. Braz. Soc. Mech. Sci. Eng., 2003, 26(1), p 22–27

E. Abele, A. Saham, and H. Schulz, Wear Mechanism When Machining Compacted Graphite Iron, CIRP Ann. Manuf. Technol., 2002, 51(1), p 53–56CrossRef

M. Gastel, C. Konetschny, U. Reuter, C. Fasel, H. Schulz, R. Riedel, and H.M. Ortner, Investigation of the Wear Mechanism of Cubic Boron Nitride Tools Used for the Machining of Compacted Graphite Iron and Grey Cast Iron, Int. J. Refract. Met. Hard. Mater., 2000, 18, p 287–296CrossRef

A.E. Reiter, V.H. Derflinger, B. Hanselmann, T. Bachmann, and B. Sartory, Investigation of the Properties of Al_1−xCrxN Coatings Prepared by Cathodic Arc Evaporation, Surf. Coat. Technol., 2005, 200, p 2114–2122CrossRef

J.L. Endrino, G.S. Fox-Rabinovich, A. Reiter, S.V. Veldhuis, R. Escobar Galindo, J.M. Albella, and J.F. Marco, Oxidation Tuning in AlCrN Coatings, Surf. Coat. Technol., 2007, 201, p 4505–4511CrossRef

J.L. Mo, M.H. Zhu, B. Lei, Y.X. Leng, and N. Huang, Comparison of Tribological Behaviours of AlCrN and TiAlN Coatings—Deposited by Physical Vapor Deposition, Wear, 2007, 263, p 1423–1429CrossRef

10.

E. Le Bourhis, P. Goudeau, M.H. Staia, E. Carrasquero, and E.S. Puchi-Cabrera, Mechanical Properties of Hard AlCrN-Based Coated Substrates, Surf. Coat. Technol., 2009, 203, p 2961–2968CrossRef

11.

F.-R. Weber, F. Fontaine, M. Scheib, and W. Bock, Cathodic arc Evaporation of (Ti, Al)N Coatings and (Ti, Al)N/TiN Multilayer-Coatings—Correlation Between Lifetime of Coated Cutting Tools, Structural and Mechanical Film Properties, Surf. Coat. Technol., 2004, 177-178, p 227–232CrossRef

12.

Shiva. Kalidas, Richard.E. DeVor, and Shiv.G. Kapoor, Experimental Investigation of the Effect of Drill Coatings on Hole Quality Under Dry and Wet Drilling Conditions, Surf. Coat. Technol., 2001, 148, p 117–128CrossRef

13.

W. Kalss, A. Reiter, V. Derflinger, C. Gey, and J.L. Endrino, Modern Coatings in High Performance Cutting Applications, Int. J. Refract. Met. Hard. Mater., 2006, 24, p 399–404CrossRef

14.

G.S. Fox-Rabinovich, B.D. Beake, J.L. Endrino, S.C. Veldhuis, R. Parkinson, L.S. Shuster, and M.S. Migranov, Effect of Mechanical Properties Measured at Room and Elevated Temperatures on the Wear Resistance of Cutting Tools with TiAlN and AlCrN Coatings, Surf. Coat. Technol., 2006, 200, p 5738–5742CrossRef

15.

M.C. Shaw, Metal Cutting Principles, 2nd ed., Oxford University Press, New York, 2005

Title: Evaluation of Hard Coating Performance in Drilling Compacted Graphite Iron (CGI)
Authors: José M. F. de Paiva Jr.
Fred L. Amorim
P. Soares
Ricardo D. Torres
Publication date: 01-10-2013
Publisher: Springer US
Published in: Journal of Materials Engineering and Performance / Issue 10/2013
Print ISSN: 1059-9495
Electronic ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-013-0601-4

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 10/2013

Modeling the Effects of Cu Variations on the Precipitated Phases and Properties of Al-Zn-Mg-Cu Alloys

Factors affecting the Inherent Hardenability of Steel

High Temperature Sliding Wear of Spray-Formed Solid-Lubricated Aluminum Matrix Composites

Development of Austempered Ductile Iron (ADI) for Automobile Crankshafts

The Use of β Titanium Alloys in the Aerospace Industry

Determination and Relaxation of Residual Stress in 2024 Al-30 vol.% Magnesium Borate Whisker Composites

Premium Partners