Top

Journal of Materials Engineering and Performance

Published in:

21-02-2017

Influence of Feedstock Materials and Spray Parameters on Thermal Conductivity of Wire-Arc-Sprayed Coatings

Authors: H. H. Yao, Z. Zhou, G. H. Wang, D. Y. He, K. Bobzin, L. Zhao, M. Öte, T. Königstein

Published in: Journal of Materials Engineering and Performance | Issue 3/2017

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

To manufacture a protective coating with high thermal conductivity on drying cylinders in paper production machines, a FeCrB-cored wire was developed, and the spraying parameters for wire-arc spraying were optimized in this study. The conventional engineering materials FeCrAl and FeCrMo coatings were produced as the reference coatings under the same experimental condition. It has been shown that the oxide content in coating influences the thermal conductivity of coating significantly. The FeCrB coating exhibits a relative higher thermal conductivity due to the lower oxide content in comparison with conventional FeCrAl and FeCrMo coatings. Moreover, the oxidation of in-flight particles can be reduced by decreasing the standoff distance contributing to the increase in the thermal conductivity of coating. Total energy consumption of a papermaking machine can be significantly reduced if the coatings applied to dryer section exhibit high thermal conductivity. Therefore, the FeCrB coating developed in this study is a highly promising coating system for drying cylinders regarding the improved thermal conductivity and low operation costs in paper production industry.

previous article Effect of Long-Term Service on Microstructure and Mechanical Properties of Martensitic 9% Cr Steel

next article Interfacial Behavior and Its Effect on Mechanical Properties of Cf/SiC Composite/TiAl6V4 Joint Brazed with TiZrCuNi

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

A.K. Ghosh, A Systematic Approach to Optimize Dryer Performance and Energy Savings-Case Studies, in Proceedings of the Tappi PaperCon’09 Conference, May 31–June 03, 2009 (St. Louis, MO, USA)

A.K. Ghosh, Fundamentals of paper drying-theory and application from industrial perspective, Evaporation, Condensation and Heat transfer, In Tech., A. Ahsan (ed.) 2011, pp. 535–541. doi:10.5772/21594. http://www.intechopen.com/books/evaporation-condensation-and-heat-transfer/fundamentals-of-paper-drying-theory-and-application-from-industrial-perspective

K. Holmberg, R. Siilasto, T. Laitinen, P. Andersson, and A. Jasberg, Global Energy Consumption Due to Friction in Paper Machines, Tribol. Int., 2013, 62, p 58–77CrossRef

P. Piltonen, T. Stoor, and J. Niinimaki, Adhesion of Pressure Sensitive Adhesives and Latex Films on Cast Iron and Low-Energy Surfaces, Int. J. Adhes. Adhes., 2012, 36, p 15–19CrossRef

R.K. Zhang and Y.L. Ma, A Probe on the Revise of Formula Coefficient for Calculation of Drier Shell in Design and Stipulation of Gray Cast Iron Dryer for Paper Machines, China Pulp Pap., 2010, 31(14), p 89–90 (in Chinese)

P. Kormano, Steam and Condensate Systems, Consideration for Dryer Section Runnability, Tappi/PIMA Papercon08 Conference, 4-7 May, 2008 (Dallas, TX, USA)

L. Yang, C.F. Liu, and G.Y. Sun, Gray Cast Iron and Its Repair Materials for the Dryers of Paper Machine, China Pulp Pap., 2008, 27(10), p 42–46 (in Chinese)

J.K. Kim, F.A. Xavier, and D.E. Kim, Tribological properties of twin wire arc spray coated aluminum cylinder liner, Mater. Des., 2015, 84, p 231–237CrossRef

R. Li, Z. Zhou, D.Y. He, L.D. Zhao, and X.Y. Song, Microstructure and High-Temperature Oxidation Behavior of Wire-arc Sprayed Fe-Based Coatings, Surf. Coat. Technol., 2014, 251, p 186–190CrossRef

10.

B. Wielage, H. Pokhmurska, M. Student, V. Gvozdeckii, T. Stupnyckyy, and V. Pokhmurskii, Iron-Based Coatings Arc-Sprayed with Cored Wires for Applications at Elevated Temperatures, Surf. Coat. Technol., 2013, 220, p 27–35CrossRef

11.

V. Pokhmurskii, M. Student, V. Gvozdeckii, T. Stupnyckyy, O. Student, B. Wielage, and H. Pokhmurska, Arc-Sprayed Iron-Based Coatings for Erosion-Corrosion Protection of Boiler Tubes at Elevated Temperatures, J. Therm. Spray Technol., 2013, 22(5), p 808–819CrossRef

12.

S. Hong, Y. Wu, W. Gao, J. Zhang, and Y. Qin, Corrosion Behavior of Arc-Sprayed Zn–Al Coating in the Presence of Sulfate-Reducing Bacteria in Seawater, J. Mater. Eng. Perform., 2015, 24, p 4449–4455CrossRef

13.

R. Li, D.Y. He, Z. Zhou, L.D. Zhao, and X.Y. Song, High Temperature Corrosion Behavior of Wire-Arc Sprayed Fe-Based Coatings, Surf. Eng., 2014, 30(8), p 573–578CrossRef

14.

R. Li, Z. Zhou, D.Y. He, Y.M. Wang, X. Wu, and X.Y. Song, Microstructure and High Temperature Corrosion Behavior of Wire-Arc Sprayed FeCrSiB Coating, J. Therm. Spray Technol., 2015, 24(5), p 857–864CrossRef

15.

W.G. Chi, Thermal transport properties of thermally sprayed coatings: an integrated study of materials, processing and microstructural effects, PhD. Thesis, Stony Brook University, USA, 2007, pp. 4–7, 79–89

16.

H.W. Jin, C.G. Park, and M.C. Kim, ‘Microstructure and Amorphization Induced by Frictional Work in Fe-Cr-B Alloy Thermal Spray Coatings, Surf. Coat. Technol., 1999, 113(1–2), p 103–112CrossRef

17.

V.V. Sobolev and J.M. Guilemany, Investigation of Coating Porosity Formation During High Velocity Oxy-Fuel (HVOF) Spraying, Mater. Lett., 1994, 18(5–6), p 304–308CrossRef

18.

S.J. Pang, T. Zhang, K. Asami, and A. Inoue, Synthesis of Fe-Cr-Mo-C-B-P Bulk Metallic Glasses with High Corrosion Resistance, Acta Mater., 2002, 50, p 489–497CrossRef

19.

Z. Zhou, L. Wang, D.Y. He, F.C. Wang, and Y.B. Liu, Microstructure and wear resisitance of Fe-based amorphous metallic coatings prepared by HVOF thermal spraying, 2010, 19(6), p 1287–1293

20.

D.J. Branagan, M. Breitsameter, B.E. Meacham, and V. Belashchenko, High-Performance Nanoscale Composite Coatings for Boiler Applications, J. Therm. Spray Technol., 2005, 14(2), p 196–204CrossRef

21.

D. Shin, F. Gitzhofer, and C. Moreau, Thermal Property Evolution of Metal Based Thermal Barrier Coatings with Heat Treatments, J. Mater. Sci., 2007, 42(15), p 5915–5923CrossRef

22.

D. Shin, F. Gitzhofer, and C. Moreau, Properties of Induction Plasma Sprayed Iron Based Nanostructured Alloy Coatings for Metal Based Thermal Barrier Coatings, J. Therm. Spray Technol., 2007, 16(1), p 118–127CrossRef

23.

L.H. Gao, H.B. Guo, L.L. Wei, C.Y. Li, and H.B. Xu, Microstructure, Thermal Conductivity and Thermal Cycling Behavior of Thermal Barrier Coatings Prepared by Plasma Spray Physical Vapor Deposition, Surf. Coat. Technol., 2015, 275, p 424–430CrossRef

24.

M. Arai, H. Ochiai, and T. Suidzu, A Novel Low-Thermal-Conductivity Plasma-Sprayed Thermal Barrier Coating Controlled by Large Pores, Surf. Coat. Technol., 2016, 285, p 120–127CrossRef

25.

L.D. Zhao, M. Maurer, F. Fischer, and E. Lugscheider, Study of HVOF Spraying of WC-CoCr Using On-line Particle Monitoring, Surf. Coat. Technol., 2004, 185, p 160–165CrossRef

26.

J.A. Gan and C.C. Berndt, Review on the Oxidation of Metallic Thermal Sprayed Coatings: A Case Study with Reference to Rare-earth Permanent Magnetic Coatings, J. Therm. Spray Technol., 2013, 22, p 1069–1091CrossRef

Title: Influence of Feedstock Materials and Spray Parameters on Thermal Conductivity of Wire-Arc-Sprayed Coatings
Authors: H. H. Yao
Z. Zhou
G. H. Wang
D. Y. He
K. Bobzin
L. Zhao
M. Öte
T. Königstein
Publication date: 21-02-2017
Publisher: Springer US
Published in: Journal of Materials Engineering and Performance / Issue 3/2017
Print ISSN: 1059-9495
Electronic ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-017-2567-0

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 3/2017

Temperature Dependence of the Surface Energy of the Low-index Planes of CaF2, BaF2 and SrF2

Microstructure and Mechanical Properties of As-cast 42CrMo Ring Blank During Hot Rolling and Subsequent Quenching and Tempering

Metallurgical Aspects of Self-lubricating Composites Containing Graphite and MoS2

Grain Size Effect of Commercial Pure Titanium Foils on Mechanical Properties, Fracture Behaviors and Constitutive Models

Friction Stir Processing of Al with Mechanically Alloyed Al-TiO2-Graphite Powder: Microstructure and Mechanical Properties

Interfacial Behavior and Its Effect on Mechanical Properties of Cf/SiC Composite/TiAl6V4 Joint Brazed with TiZrCuNi

Premium Partners