Top

Metallurgist

Published in:

02-02-2022

Investigation of the Distribution Parameters and Technological Properties of Steel 20X23H18 Powders Produced by Plasma Melting and Centrifugal Spraying of Rapidly Rotating Cast Billets

Authors: A. E. Knyazev, P. G. Min, A. V. Vostrikov

Published in: Metallurgist | Issue 9-10/2022

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

In this study, we investigated distribution parameters such as particle size, of both powder and metalpowder composite (MPC) forms of steel 20X23H18 with a fraction of less than 63 microns after plasma melting and centrifugal spraying of a rapidly rotating cast billet using the plasma rotate electrode process method. We have discussed the morphology (appearance) of the MPC particles with a fraction of less than 63 microns. The flowability, angle of repose (looseness), and relative and bulk densities of the MPC were determined, and the yield ratio of the MPC was calculated. The quality of steel grade 20X23H18 MPC with a fraction of less than 63 microns and its application in the manufacture of parts by the method of selective laser sintering are discussed.

previous article Investigation of the Properties of High-Strengh Aluminum Alloy 1580 for Producing Deformed Semi-Finished Products Suitable for Use Under the Far North and Arctic Conditions

next article Development and Practical Use of the Steel Hardenability Engineering Program

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

E. N. Kablov, “ARIAM: new generation materials for PD-14,” Krylia Rodiny, No. 7-8, 54–58 (2019).

E. N. Kablov, “Present and future of additive technologies,” Metal. Evraz., No. 1, 2-6 (2017).

E. N. Kablov, “Additive technologies as the dominant of the national technological initiative,” Intellekt Tekhnol., No. 2 (11), 52–55 (2015).

P. G. Min, V. E. Vadeev, A. M. Rogalev, and A. E. Knyazev, “Investigation of the chemical composition, structure, and mechanical properties of EP648 alloy at various stages of additive production,” Materialovedenie, No. 12, 17–22 (2018).

E. N. Kablov, “Powders release from unnecessary things,” Expert, No. 49 (926), 46–51 (2014).

H. Fayazfar, M. Salarian, A. Rogalsky, D. Sarker, P. Russo, V. Paserin, and E. Toyserkani, “A critical review of powder-based additive manufacturing of ferrous alloys: process parameters, microstructure and mechanical properties,” Mater. Des., 144, 98–128 (2018).CrossRef

D. Barletta, M. Poletto, and A. C. Santomaso, “Bulk powder flow characterization techniques,” in: Powder Flow: Theory, Characterization and Application, eds. A. Hassanpour, Hare C. Pasha M. Royal Society of Chemistry (2019); https://doi.org/https://doi.org/10.1039/9781788016100-00064.

M. I. Alishin and A. E. Knyazev, “Production of high-purity metal-powder compositions of titanium alloys by induction gas atomization for additive technologies,” Tr. VIAM: Electron. Nauch.-Techn. Zhur., No. 11 (59), Art. 05 (2017); http://www.viam-works.ru (reference date: 06/09/2020); DOI: https://doi.org/10.18577/2307-6046-2017-0-11-5-5.

A. E. Knyazev and A. V. Vostrikov, “Sieving of powders in additive and granular production (review),” Tr. VIAM: Electron. Nauch.-Techn. Zhur., No. 11, Art. 02 (2020); http://www.viam-works.ru (reference date: 12/06/2020); DOI: https://doi.org/10.18577/2307-6046-2020-0-11-11-20.

10.

E. N. Kablov, “Innovative developments of ARIAM State Scientific Center of the RF for implementation of “Strategic directions for the development of materials and technologies for their processing for the period up to 2030”,” Aviatsion. Mater. Tekhnol., No. 1, 3–33 (2015); DOI: https://doi.org/10.18577/2071-9140-2015-0-1-3-33.

11.

J. Dawes, R. Bowerman, and R. Trepleton, “Introduction to the additive manufacturing powder metallurgy supply chain,” Johns. Matthey Technol. Rev., 59, No. 3, 243–256 (2015); https://doi.org/https://doi.org/10.1595/205651315x688686.

12.

S. A. Oglezneva, A. A. Smetkin, V. I. Mitin, and K. V. Kalinin, “Influence of the parameters of atomization of the melt on the technological characteristics of powder grade 12X18H10T,” Vestn. PNIPU. Mashinostr. Materialoved., No. 4, 112–138 (2017); URL: https://cyberleninka.ru/article/n/vliyanie-parametrov-atomizatsii-rasplava-na-tehnologicheskie-harakteristiki-poroshka-marki-12h18n10t (reference date: 12/06/2020).

13.

A. G. Evgenov, S. V. Nerush, and S. A. Vasilenko, “Production and testing of a finely dispersed metal powder of a high-chromium nickel-based alloy as applied to laser lmd surfacing,” Tr. VIAM: Electron. Nauch.-Techn. Zhur., No. 5, Art. 04 (2014); http://www.viam-works.ru (reference date: 02/23/2021); DOI: https://doi.org/10.18577/2307-6046-2014-0-5-4-4.

14.

A. G. Evgenov, S. I. Shcherbakov, and A. M. Rogalev, “Testing of EP718 and EP648 heat-resistant alloys powders produced ARIAM for the repair of gas-turbine engine parts by laser gas-powder surfacing,” Aviatsion. Mater. Tekhnol., No. S1 (43), 16–23 (2016); DOI: https://doi.org/10.18577/2071-9140-2016-0-81-16-23.

15.

A. E. Knyazev, S. V. Nerush, M. I. Alishin, and I. S. Kuko, “Research of technological properties of metal-powder compositions of titanium alloys VT6 and VT20, obtained by induction melting and gas atomization,” Tr. VIAM: Electron. Nauch.-Techn. Zhur., No. 11 (59), Art. 06 (2017); http://www.viam-works.ru (reference date: 06/09/2020); DOI: https://doi.org/10.18577/2307-6046-2017-0-11-6-6.

16.

A. I. Rodionov, I. Yu. Efimochkin, A. V. Samokhin, and M. A. Sinaisky, “Influence of the spheroidization process on the fractional composition and morphology of the VKNA-4U alloy reinforced with Al2O3-Y2O3 particles,” Tr. VIAM: Electron. Nauch.-Techn. Zhur., No. 11, Art. 02 (2019); http://www.viam-works.ru (reference date: 02/23/2021); DOI: https://doi.org/10.18577/2307-6046-2019-0-11-12-21.

17.

N. F. Anoshkin, “Metallurgy of granules of heat-resistant nickel alloys at the present state of art,” Metallurg. Granul, 4, 46–59 (1988).

18.

V. T. Musienko and V. Ya. Koshelev, “Problems of Obtaining Granules of Heat-Resistant Nickel Alloys for the Manufacture of Units of Gas-Turbine Power Plants,” Metallurgy and Processing of Titanium and Heat-Resistant Alloys, VILS, Moscow (1991), pp. 300–312.

19.

V. T. Musienko, Development of Theoretical Foundations and Technology for the Production of Metal Powders at High and Ultra-High Cooling Rates of Centrifugal Spraying Methods for the Manufacture of Gas Turbine Engine Disks, Author’s abstract, Ph. D. Thesis in Engineering Science, VILS, Moscow (1991).

20.

V. Ya. Koshelev and A. E. Knyazev, “Scientific and technical aspects of creating a new generation plant for the production of granules by the method of plasma rotate electrode process,” New Materials and Technologies in Aviation and Rocket and Space Technology, IPK Mashpribor, Korolev, Moscow region (2004), pp. 72–75.

21.

V. Ya. Koshelev, Research of the Process, Development, and Implementation of Industrial Technology for Thermal Degassing of Granules of Heat-Resistant Nickel Alloys of EP741P Type in the Production of Billets for Gas Turbine Engine Disks, Author’s Abstract, Ph. D. Thesis in Engineering Science, VILS, Moscow (1985).

22.

A. V. Vostrikov and D. I. Sukhov, “Production of granules by the PREP method for additive technologies ― state of art and development prospects,” Tr. VIAM: Electron. Nauch.-Techn. Zhur., No. 8 (44), Art. 03 (2016); http://www.viam-works.ru (accessed: 06/09/2020); DOI: https://doi.org/10.18577/2307-6046-2016-0-8-3-3.

23.

V. Ya. Koshelev and A. E. Knyazev, “Influence of the quality of processing of cast polished billets on the amplitude of their vibration when rotating at high frequency on the UCR-4/V Unit,” in: New Materials and Technologies in Aviation and Rocket-Space Technology, IPK Mashpribor, Korolev, Moscow region (2007), pp. 8–9.

24.

V. Ya. Koshelev, G. S. Garibov, and D. I. Sukhov, “The main regularities of the process of manufacturing granules of heat-resistant alloys by the method of plasma rotate electrode process,” Tekhnolog. Legk. Splav., No. 3, 97–103 (2015).

25.

B. Champagne and R. Angers, “REP (rotating electrode process) atomization mechanisms,” J. Powder Metal Int., 16, 125–128 (1984).

26.

V. T. Musienko, “Aspects of plasma rotate electrode process,” Metallurg. Granul, 3, 23–33 (1986).

27.

N. P. Karapatis, A Sub-Process Approach of Selective Laser Sintering, Ph. D. Thesis, Ecole Polytechnique Federal de Lausanne (2001).

28.

X. Gong, B. Cheng, S. Price, and K. Chou, Powder-Bed Electronbeam-Melting Additive Manufacturing: Powder Characterization, Process Simulation and Metrology: ASME Early Career Technical Conf. (ECTC), Birmingham, AL, USA, District F, Section 2, 59–66 (2013).

29.

N. P. Karapatis, G. Egger, P. E. Gygax, and R. Glardon, “Optimization of powder layer density in selective laser sintering,” in Proc. of the 22nd Solid Freeform Fabrication Sym. (Austin, TX, USA, 9–11 August 1999) (1999), pp. 255–263.

30.

V. L. Girshov, S. A. Kotov, and V. N. Tsemenko, Modern Technologies in Powder Metallurgy: Study Guide, Izdatel’stvo Politekhn Universiteta, St. Petersburg (2010), pp. 200–214.

31.

A. B. Spierings, N. Herres, and G. Levy, “Influence of the particle size distribution on surface quality and mechanical properties in additive manufactured stainless steel parts,” in: 21th Solid Freedom Fabrication Symp. (Austin, Texas, USA, 2008) (2008), pp. 397–406.

32.

A. B. Spierings and G. Levy, “Comparison of density of stainless steel 316l parts produced with selective laser melting using different powder grades,” in Proc. of the 22nd Solid Freeform Fabrication Symp. (Austin, TX, USA. 3–5 August 2009) (2009), pp. 342–353.

33.

R. Frykholm, Y. Takeda, B.-G. Andersson, and R. Carlstrom, “Solid state sintered 3-D printing component by using inkjet (binder) method,” J. Jpn Soc. Powder Powder Metall., 63, 7, 421–426 (2016); DOI: http://doi.org/https://doi.org/10.2497/jjspm.63.421.

34.

R. L. Carr, “Evaluating flow properties of solids,” Chem. Eng., 18(1), 163–168 (1965).

Title: Investigation of the Distribution Parameters and Technological Properties of Steel 20X23H18 Powders Produced by Plasma Melting and Centrifugal Spraying of Rapidly Rotating Cast Billets
Authors: A. E. Knyazev
P. G. Min
A. V. Vostrikov
Publication date: 02-02-2022
Publisher: Springer US
Published in: Metallurgist / Issue 9-10/2022
Print ISSN: 0026-0894
Electronic ISSN: 1573-8892
DOI: https://doi.org/10.1007/s11015-022-01245-x

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 9-10/2022

Effect of MgO Content on Properties of Bahariya Iron Ore Sinter under the Conditions of Egyptian Iron & Steel Company (EISCO)

Metallurgist Volume 65, Number 9

Formation of Microstructure and Properties During Isothermal Treatment of Aircraft Building Steel

Correction to: New Approach to Bearing Steel Quality Evaluation

Fire Refining of Rough Antimony from Impurities for Obtaining High-Grade Antimony

Influence of the Method of Making Frac Balls from Magnesium Alloys on their Performance Characteristics during Hydraulic Fracturing

Premium Partners