Skip to main content
main-content
Top

Journal

Journal of Mechanical Science and Technology

Journal of Mechanical Science and Technology 8/2013

Issue 8/2013

Table of Contents ( 38 Articles )

01-08-2013 | Issue 8/2013

Discrete optimization of rigid rotor balancing

Tanguy Messager, Mariusz Pyrz

01-08-2013 | Issue 8/2013

Electrical impedance as signal to monitor healthy state of eardrum-like membranes

Jin Xie, Shih-Fu Ling

01-08-2013 | Issue 8/2013

A novel experimental research on vibration characteristics of the running high-speed motorized spindles

Wentao Shan, Xiaoan Chen, Ye He, Jinming Zhou

01-08-2013 | Issue 8/2013

Condition monitoring of naturally damaged slow speed slewing bearing based on ensemble empirical mode decomposition

Wahyu Caesarendra, Prabuono Buyung Kosasih, Anh Kiet Tieu, Craig Alexander Simpson Moodie, Byeong-Keun Choi

01-08-2013 | Issue 8/2013

Numerical and experimental investigation of the bell-mouth inlet design of a centrifugal fan for higher internal flow rate

Sanghyeon Kim, Seung Heo, Cheolung Cheong, Tae-Hoon Kim

01-08-2013 | Issue 8/2013

Cyclic damage model for E-shaped dampers in the seismic isolation system

Dong Keon Kim, Gary F. Dargush, Jong Wan Hu

01-08-2013 | Issue 8/2013

Carbody hunting investigation of a high speed passenger car

Caihong Huang, Jing Zeng, Shulin Liang

01-08-2013 | Issue 8/2013

Multi-stage diagnostic system for reciprocating compressor using DTW technique

H. C. Kim, M. G. Cho, J. Shim

01-08-2013 | Issue 8/2013

Experimental and numerical study on the burst pressure of steam generator tubes with L- and U-type through-wall combination cracks

Kyu In Shin, Kee Bong Yoon, Jai Hak Park

01-08-2013 | Issue 8/2013

Transient analysis of several cracks in an orthotropic material under impact load

M. M. Monfared, M. Ayatollahi

01-08-2013 | Issue 8/2013

Investigation of fatigue properties of shot peened and plasma nitrocarburized P/M FC0205 steel

Ali Başaran, Naci Kurgan, Remzi Varol

01-08-2013 | Issue 8/2013

Effect of induction heating on fatigue life of drive plate for dual mass flywheel

Yong-Jun Lee, Tae-Yang Shim, Kwang-O Lee, Man-Dae Hur, Sung-Su Kang

01-08-2013 | Issue 8/2013

Comparative study on the high-temperature tensile and creep properties of Alloy 617 base and weld metals

Woo-Gon Kim, Jae-Young Park, I. M. W. Ekaputra, Sung-Deok Hong, Seon-Jin Kim, Yong-Wan Kim

01-08-2013 | Issue 8/2013

Lattice Boltzmann simulation of turbulent natural convection in a square cavity using Cu/water nanofluid

H. Sajjadi, M. Beigzadeh Abbassi, GH. R. Kefayati

01-08-2013 | Issue 8/2013

Numerical analysis of interior ballistics through eulerian-lagrangian approach

Jin-Sung Jang, Hyung-Gun Sung, Tae-Seong Roh, Dong-Whan Choi

01-08-2013 | Issue 8/2013

A computational analysis of the airflow in a twin-track subway tunnel with a sliding-curtain to improve ventilation performance

Makhsuda Juraeva, Kyung Jin Ryu, Sang-Hyun Jeong, Dong Joo Song

01-08-2013 | Issue 8/2013

Aerodynamic design and analysis of a small-scale vertical axis wind turbine

Jelena Svorcan, Slobodan Stupar, Dragan Komarov, Ognjen Peković, Ivan Kostić

01-08-2013 | Issue 8/2013

Numerical study on near-stall flow unsteadiness in an axial compressor with casing treatment

Yoojun Hwang, Shin-Hyoung Kang

01-08-2013 | Issue 8/2013

An ultra-high pressure sensor with cylinder structure

Libo Zhao, Xin Guo, Xiawei Meng, Rahman Hebibul, Yulong Zhao, Jianzhu Wang, Zhuangde Jiang

01-08-2013 | Issue 8/2013

Workspace quality analysis and application for a completely restrained 3-Dof planar cable-driven parallel manipulator

Xiaoqiang Tang, Lewei Tang, Jinsong Wang, Dengfeng Sun

01-08-2013 | Issue 8/2013

Development of a geometric modeling tool for rectangular drawbeads in draw dies

Yun Chan Chung

01-08-2013 | Issue 8/2013

A function-behavior-structure framework for quantification and reproduction of emotional haptic experience in using an electronic device

Il-ju Bae, Soo-Hong Lee, Hyung-seok Ok, Jaein Lee

01-08-2013 | Issue 8/2013

Internal stress analysis of a stepped rounded D-ring under a uniform squeeze rate and internal pressure using a photoelastic experimental hybrid method

Bruno Robert Mose, Jeong Hwan Nam, Lim Hyun Seok, Jai-Sug Hawong

01-08-2013 | Issue 8/2013

Static deflection and pull-in instability analysis of an electrostatically actuated mirocantilever gyroscope considering geometric nonlinearities

Mahdi Mojahedi, Mohammad Taghi Ahmadian, Keikhosrow Firoozbakhsh

01-08-2013 | Issue 8/2013

Investigation of the dynamic bending moment transmitted to the forging manipulator due to press motion

Gang Li, Wenjie Sun, Deshi Liu

01-08-2013 | Issue 8/2013

Influence of graphite and machining parameters on the surface roughness of Al-fly ash/graphite hybrid composite: a Taguchi approach

P. Shanmughasundaram, R. Subramanian

01-08-2013 | Issue 8/2013

Genetic algorithm based optimization of the process parameters for gas metal arc welding of AISI 904 L stainless steel

P. Sathiya, P. M. Ajith, R. Soundararajan

01-08-2013 | Issue 8/2013

Experimental modeling and multi-objective optimization of traveling wire electrochemical spark machining (TW-ECSM) process

Basanta Kumar Bhuyan, Vinod Yadava

01-08-2013 | Issue 8/2013

Study of an adaptive fuzzy algorithm to control a rectangular-shaped unmanned surveillance flying car

Kuktae Kim, Kyoil Hwang, Hoonmo Kim

01-08-2013 | Issue 8/2013

Output feedback tracking control of uncertain robot manipulators via higher-order sliding-mode observer and fuzzy compensator

Mien Van, Hee-Jun Kang, Young-Soo Suh, Kyoo-Sik Shin

01-08-2013 | Issue 8/2013

Investigation of the effects of geometrical parameters on heat transfer from buried finned pipes

Hakan Demir, Ahmet Koyun, Ş. Özgür Atayılmaz, Özden Ağra, Ahmet Selim Dalkılıç

01-08-2013 | Issue 8/2013

Effects of equivalence ratio and carbon dioxide concentration on premixed charge compression ignition of gasoline and diesel-like fuel blends

Dong Han, Huanyu Guang, Zheng Yang, Xingcai Lu, Zhen Huang

01-08-2013 | Issue 8/2013

Feasibility study of a hybrid renewable energy system with geothermal and solar heat sources for residential buildings in South Korea

Young-Ju Kim, Nam-Sub Woo, Sung-Cheol Jang, Jeong-Ju Choi

01-08-2013 | Issue 8/2013

Analysis of heat transfer inside wall-joint-fins systems

A. -R. A. Khaled, A. Gari

01-08-2013 | Issue 8/2013

Aerodynamic optimisation of a low-pressure multistage turbine using the response-surface method

Yu Li, Liang Li, Tong Zhao, Jun Li

01-08-2013 | Issue 8/2013

Influence of steam injection and hot gas bypass on the performance and operation of a combined heat and power system using a recuperative cycle gas turbine

Soo Young Kang, Jeong Ho Kim, Tong Seop Kim

01-08-2013 | Issue 8/2013

Modeling and numerical simulation of a pilot-stabilized turbulent premixed flame

Abdallah Benarous, Djamel Karmed, Abdelkrim Liazid

01-08-2013 | Issue 8/2013

Performance and emission characteristics of conventional engine running on jatropha oil

B. P. Singh

Current Publications

Premium Partners

    Image Credits