Skip to main content
Disciplines
Automotive Business IT + Informatics Construction + Real Estate Electrical Engineering + Electronics Energy + Sustainability Insurance + Risk Finance + Banking Management + Leadership Marketing + Sales Mechanical Engineering + Materials
Events
DE
EN
Books
Journals
Topic Page
Marketing
Start single access now
Access for companies
EXTENDED SEARCH
Log in
Top
Metallurgist
Published in: Metallurgist 9-10/2021

29-01-2021

Prediction of Billet Fracture at Two-High Screw Rolling Piercing

Authors: Yu. V. Gamin, M. M. Skripalenko, B. A. Romantsev, M. V. Kadach

Published in: Metallurgist | Issue 9-10/2021

Log in

Activate our intelligent search to find suitable subject content or patents.

search-config
loading …

Abstract

Two-high screw piercing of steel 50 billets was performed at feed angles of 15 and 18 degrees. Piercing was stopped at 10–12 mm distance from the rear end of the billet. Axial fracture was registered at 15 degrees feed angle in front of the mandrel nose, while no fracture was observed at 18 degrees feed angle. Piercing for similar parameters was simulated using DEFORM finite element analysis software, and several criteria were used for fracture prediction. Ayada criterion was ineffective, as evidenced by the comparison with experimental data. The normalized Cockcroft–Latham criterion was effective for fracture prediction only in the axial zone. Results of this study showed that the most effective technique for fracture prediction is the construction of a dependence of “accumulated strain–stiffness coefficient of tension” along the trajectory of the point movement.
previous article Evaluation of the Corrosion Resistance of Tubing of Various Strength Groups
next article Influence of Equal-Channel Angular Pressing on Changes in the Microstructure of Steel Grade 1055

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

  • über 102.000 Bücher
  • über 537 Zeitschriften

aus folgenden Fachgebieten:

  • Automobil + Motoren
  • Bauwesen + Immobilien
  • Business IT + Informatik
  • Elektrotechnik + Elektronik
  • Energie + Nachhaltigkeit
  • Finance + Banking
  • Management + Führung
  • Marketing + Vertrieb
  • Maschinenbau + Werkstoffe
  • Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

  • über 67.000 Bücher
  • über 390 Zeitschriften

aus folgenden Fachgebieten:

  • Automobil + Motoren
  • Bauwesen + Immobilien
  • Business IT + Informatik
  • Elektrotechnik + Elektronik
  • Energie + Nachhaltigkeit
  • Maschinenbau + Werkstoffe




 

Jetzt Wissensvorsprung sichern!

inform now
Literature
1.
P. T. Emel’yanenko, The Theory of Oblique and Pilgrim Rolling [in Russian], Metallurgizdat, Moscow (1949).
2.
A. P. Chekmarev, Ya. L. Vatkin, M. I. Khanin, V. I. Biba, and N. S. Kirvalidze, Piercing in Cross-Roll Mills [in Russian], Metallurgiya, Moscow (1967).
3.
I. A. Fomichev, Skew Rolling [in Russian], Metallurgizdat, Moscow (1963).
4.
K. Gruber, “Uber die Herstellung nahtloser Rohre unter besonderer Berucksichtigung des Mannesmann-Schragwalzverfahrens,” Stahl Eisen, 38, No. 36, 40–42 (1919).
5.
V. K. Vorontsov and V. A. Belevitin, Revisiting the Macrofracture of the Axial Zone of a Solid Billet during Screw Rolling: Proceedings of MISiS, No. 119, “Theory and technology of metal strain,” Metallurgiya, Moscow (1979).
6.
V. L. Kolmogorov, Stresses, Strains, Fracture [in Russian], Metallurgiya, Moscow (1970).
7.
A. A. Bogatov, O. I. Mizhiritskiy, and K. S. Smirnov, Resource of Metal Ductility during Pressure Treatment [in Russian], Metallurgiya, Moscow (1984).
8.
K. L. Kolmogorov, A. A. Bogatov, B. A. Ligachev et al., Ductility and Fracture [in Russian], Metallurgiya, Moscow (1984).
9.
E. Siebel, “Grundsatzliche Betrachtungenzum Schrag-walzverfahren,” Stahl Eisen, No. 11, 11–15 (1927).
10.
I. A. Fomichev, “Strain of the metal in the oblique rolling mill,” Stal’, No. 11, 45 (1965).
11.
V. S. Smirnov et al., “Cross Rolling in Mechanical Engineering,” Mashgiz, Moscow (1957).
12.
V. S. Smirnov, “Influence of the strain mode on the formation of a cavity during piercing,” Stal’, No. 8, 754–757 (1953).
13.
R. L. Shatalov and V. A. Medvedev, “Effect of deformed workpiece temperature inhomogeneity on mechanical properties of thinwalled steel vessels during treatment in a rolling and pressing line,” Metallurgist, 63, 176–182 (2019).CrossRef
14.
R. L. Shatalov, V. A. Medvedev, and E. E. Zagoskin, “Determination of mechanical properties of steel thinwalled vessels by hardness after hot screw rolling with subsequent stamping and quenching,” Chern. Metall., 7, 36–40 (2019).
15.
Yu. V. Gamin, Development of Technology and Equipment for Hot Rolling of Hollow Billets with a Small Diameter Bottom, Dissertation Abstract of PhD in Technical Sciences, NITU MISiS, Moscow (2017).
16.
B. A. Romantsev, Y. V. Gamin, A. V. Goncharuk, and A. S. Aleshchenko, “Innovative equipment for producing cost- effective hollow billets for mechanical-engineering parts of small diameter,” Metallurgist, 61, No. 3-4, 217–222 (2017).CrossRef
17.
M. Skripalenko, V. Bazhenov, B. Romantsev, M. Skripalenko, A. Koltygin, and A. Sidorov, “Computer modeling of chain processes in the manufacture of metallurgical products,” Metallurgist, 58, No. 1-2, 86–90 (2014).CrossRef
18.
M. Skripalenko, D. Ashikhmin, M. Skripalenko, A. Sidorov, and Y. Xu, “Use of the software deform 2D to model the process of rolling with vibration of the top work roll,” Metallurgist, 56, No. 11-12, 844–847 (2013).
19.
Z. Pater, “A comparative analysis of forming railway axles in 3- and 4-roll rolling mills,” Materials, 13, No. 3084 (2020).
20.
21.
Y. Chastel, A. Diop, S. Fanini, P. O. Bouchard, and K. Mocellin, “Finite element modeling of tube piercing and creation of a crack,” Int. J. Mater. Form., 1, No. S1, 355–358 (2008).CrossRef
22.
M. M. Skripalenko, B. A. Romantsev, S. P. Galkin, M. N. Skripalenko, L. M. Kaputkina, and T. B. Huy, “Prediction of the fracture of metal in the process of screw rolling in a two-roll mill,” Metallurgist, 61, No. 11-12, 925–933 (2018).CrossRef
23.
D. A. Berazategui, M. A. Cavaliere, L. Montelatici, and E. N. Dvorkin, “On the modelling of complex 3D bulk metal forming processes via the pseudo-concentrations technique. Application to the simulation of the Mannesmann piercing process,” Int. J. Numer. Meth. Eng., 65, No. 7, 1113–1144 (2006).CrossRef
24.
25.
M. M. Skripalenko, S. P. Galkin, Her Jae Sung, B. A. Romantsev, Ba Huy Tran, L. M. Kaputkina, M. N. Skripalenko, and A. A. Sidorow, “Prediction of potential fracturing during radial-shear rolling of continuously cast copper billets by means of computer simulation,” Metallurgist, 62, 849–856 (2019).CrossRef
26.
S. P. Galkin, “Regulating radial-shear and screw rolling on the basis of the metal trajectory,” Steel Transl., 34, No. 7, 57–60 (2004).
27.
V. L. Kolmogorov, Mechanics of Metal Processing by Pressure [in Russian], Izd-vo Uralskogo GTU, Yekaterinburg (2001).
28.
S. P. Galkin, B. A. Romantsev, and E. A. Kharitonov, “Putting into practice innovative potential in the universal radial-shear rolling process,” CIS Iron Steel Rev., 2014, No. 9, 35–39 (2014).
29.
V. Sheremetyev, A. Kudryashova, S. Dubinskiy, S Galkin., S. Prokoshkin, and V. Brailovski, “Structure and functional properties of metastable beta Ti-18Zr-14Nb (at.%) alloy for biomedical applications subjected to radial shear rolling and thermomechanical treatment,” J. Alloys Compds., 737, No. 15, 678–683 (2018).
30.
A. V. Belevich, Modeling of Indicators of Ductility and Resistance to Strain of Steels and Alloys: a Workshop on Technological Mechanics, Izd-vo VlGU, Vladimir (2005).
31.
P. I. Polukhin, G. Ya. Gun, and A. M. Galkin, Resistance to Plastic Strain of Metals and Alloys. Book of Reference, Metallurgiya, Moscow (1983).
Metadata
Title
Prediction of Billet Fracture at Two-High Screw Rolling Piercing
Authors
Yu. V. Gamin
M. M. Skripalenko
B. A. Romantsev
M. V. Kadach
Publication date
29-01-2021
Publisher
Springer US
Published in
Metallurgist / Issue 9-10/2021
Print ISSN: 0026-0894
Electronic ISSN: 1573-8892
DOI
https://doi.org/10.1007/s11015-021-01093-1

Other articles of this Issue 9-10/2021

Metallurgist 9-10/2021 Go to the issue

OriginalPaper

Specifics of Forming and Operating Self-Sintering Electrodes of Slag-Cleaning Electric Furnaces of Nadezhdinsk Metallurgical Plant

OriginalPaper

Production of New-Generation Rolled Steel under Conditions of Magnitogorsk Iron and Steel Company

OriginalPaper

Study of Chemical Inhomogeneity in Beta-Solidifying TiAl Alloys of Various Composition

OriginalPaper

Development and Application of the Theory of Rigid Ends in Thin-Sheet Rolling

OriginalPaper

Effect of the Slag Layer Thickness, Gas Composition, and Furnace Capacity on the Arc Efficiency and Heat Transfer in Arc Furnaces. Part I. Effect of the Slag Thickness and Furnace Capacity on Arc Efficiency

OriginalPaper

Study of Conditions for Improving Chemical and Structural Homogeneity of Ferritic Class Hot-Rolled Steels

Premium Partners

    Image Credits