Top

Microsystem Technologies

Published in:

01-10-2014 | Technical Paper

Rapid and low cost replication of complex microfluidic structures with PDMS double casting technology

Authors: Luxia Yang, Xiaojian Hao, Chunshui Wang, Binzhen Zhang, Wanjun Wang

Published in: Microsystem Technologies | Issue 10-11/2014

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

In this paper, a new method for fast and precise replication of high-aspect-ratio microfluidic structures is reported. First, SU-8 microfluidic structures on the master mold were replicated into Polydimethylsiloxane (PDMS), which served as an intermediate, negative mold, by a conventional soft lithography process. The PDMS negative mold was then treated by wetting its surface with a diluted aqueous solution of a hydrophilic polymer, hydroxypropylmethylcellulose and rinsed with deionized water. Last, the negative mold was used in yet another PDMS molding process to produce a PDMS replica of the microfluidic structures (the hydrofocusing unit for a micro-cytometer) with the same structures as the master mold. Experimental results showed that microstructures with high-aspect-ratio could be consistently replicated with high fidelity. This technique can not only greatly simplify the design and fabrication of master molds, but also protect the expensive and fragile original master mold. The process does not require sophisticated equipment and is well suited for the replication of precision master structures in bulk quantities at low cost.

previous article Low cost method for hot embossing of microstructures on PMMA by SU-8 masters

next article Nano-microscale moulding of some metal plates with high strength Ni–W alloy moulds

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

Ahn CH, Choi J-W, Beaucage G, Nevin JH, Lee J-B, Puntambekar A et al (2004) Disposable smart lab on a chip for point-of-care clinical diagnostics. Proc IEEE 92:154–173CrossRef

Amirfazli A, Kwok D, Gaydos J, Neumann A (1998) Line tension measurements through drop size dependence of contact angle. J Colloid Interface Sci 205:1–11CrossRef

Anderson JR, Chiu DT, Wu H, Schueller OJ, Whitesides GM (2000) Fabrication of microfluidic systems in poly (dimethylsiloxane). Electrophoresis 21:27–40CrossRef

Bashir R (2004) BioMEMS: state-of-the-art in detection, opportunities and prospects. Adv Drug Deliv Rev 56:1565–1586CrossRef

Bhattacharya S, Datta A, Berg JM, Gangopadhyay S (2005) Studies on surface wettability of poly (dimethyl) siloxane (PDMS) and glass under oxygen-plasma treatment and correlation with bond strength. Microelectromech Syst J 14:590–597CrossRef

Bodas D, Khan-Malek C (2007) Hydrophilization and hydrophobic recovery of PDMS by oxygen plasma and chemical treatment—An SEM investigation. Sensors Actuators B Chem 123:368–373CrossRef

Cayre O, Paunov VN, Velev OD (2003) Fabrication of asymmetrically coated colloid particles by microcontact printing techniques. J Mater Chem 13:2445–2450CrossRef

Chen I-J, Lindner E (2007) The stability of radio-frequency plasma-treated polydimethylsiloxane surfaces. Langmuir 23:3118–3122CrossRef

Efimenko K, Wallace WE, Genzer J (2002) Surface modification of Sylgard-184 poly (dimethyl siloxane) networks by ultraviolet and ultraviolet/ozone treatment. J Colloid Interface Sci 254:306–315CrossRef

Friese C, Werber A, Krogmann F, Mönch W, Zappe H (2007) Materials, effects and components for tunable micro-optics. IEEJ Trans Electr Electron Eng 2:232–248CrossRef

Gitlin L, Schulze P, Belder D (2009) Rapid replication of master structures by double casting with PDMS. Lab Chip 9:3000–3002CrossRef

Hassanin H, Jiang K (2011) Multiple replication of thick PDMS micropatterns using surfactants as release agents. Microelectron Eng 88:3275–3277CrossRef

Hu S, Ren X, Bachman M, Sims CE, Li G, Allbritton N (2002) Surface modification of poly (dimethylsiloxane) microfluidic devices by ultraviolet polymer grafting. Anal Chem 74:4117–4123CrossRef

Jo B-H, Van Lerberghe LM, Motsegood KM, Beebe DJ (2000) Three-dimensional micro-channel fabrication in polydimethylsiloxane (PDMS) elastomer. Microelectromech Syst J 9:76–81CrossRef

Kim H, Urban MW (1996) Reaction sites on poly (dimethylsiloxane) elastomer surfaces in microwave plasma reactions with gaseous imidazole: a spectroscopic study. Langmuir 12:1047–1050CrossRef

Kim Y, Suh K, Lee HH (2001) Fabrication of three-dimensional microstructures by soft molding. Appl Phys Lett 79:2285–2287CrossRef

Maji D, Lahiri SK, Das S (2012) Study of hydrophilicity and stability of chemically modified PDMS surface using piranha and KOH solution. Surf Interface Anal 44:62–69CrossRef

Manz A, Graber N, Widmer H (1990) Miniaturized total chemical analysis systems: a novel concept for chemical sensing. Sensors Actuators B Chem 1:244–248CrossRef

McDonald JC, Whitesides GM (2002) Poly (dimethylsiloxane) as a material for fabricating microfluidic devices. Acc Chem Res 35:491–499CrossRef

Möllenbeck S, Bogdanski N, Mayer A, Scheer HC, Zajadacz J, Zimmer K (2010) 172 nm pre-treatment for PDMS/PDMS replication. Microelectron Eng 87:1519–1521CrossRef

Nguyen N-T (2010) Micro-optofluidic Lenses: a review. Biomicrofluidics 4:031501CrossRef

Rust M, Subramaniam S, Ahn C (2005) Fabrication of nanochannels with microfluidic interface using PDMS casting on Si/Ti nanomold. In: Technical Proceeding of the 8th NSTI Nanotechnology Conference and Trade Show (Nanotech 2005) (Anaheim, CA, 8–12 May 2005) vol. 2, pp 464–466

Schnyder B, Lippert T, Kötz R, Wokaun A, Graubner V-M, Nuyken O (2003) UV-irradiation induced modification of PDMS films investigated by XPS and spectroscopic ellipsometry. Surf Sci 532–535:1067–1071CrossRef

Shao G, Qiu W, Wang W (2010) Fast replication of out-of-plane microlens with polydimethylsiloxane and curable polymer (NOA73). Microsyst Technol 16:1471–1477CrossRef

Shao G, Wu J, Cai Z, Wang W (2012) Fabrication of elastomeric high-aspect-ratio microstructures using polydimethylsiloxane (PDMS) double casting technique. Sens Actuators A 178:230–236CrossRef

Tavana H, Simon F, Grundke K, Kwok D, Hair M, Neumann A (2005) Interpretation of contact angle measurements on two different fluoropolymers for the determination of solid surface tension. J Colloid Interface Sci 291:497–506CrossRef

Vancso GJ, Hillborg H, Schönherr H (2005) Chemical composition of polymer surfaces imaged by atomic force microscopyand complementary approaches. In: Polymer Analysis Polymer Theory, Springer, 2005, pp 55–129

Whitesides GM, Ostuni E, Takayama S, Jiang X, Ingber DE (2001) Soft lithography in biology and biochemistry. Annu Rev Biomed Eng 3:335–373CrossRef

Wong I, Ho C-M (2009) Surface molecular property modifications for poly (dimethylsiloxane)(PDMS) based microfluidic devices. Microfluid Nanofluid 7:291–306CrossRef

Wu H, Odom TW, Chiu DT, Whitesides GM (2003) Fabrication of complex three-dimensional microchannel systems in PDMS. J Am Chem Soc 125:554–559CrossRef

Yang R, Wang W (2004) Out-of-plane polymer refractive microlens fabricated based on direct lithography of SU-8. Sens Actuators A 113:71–77CrossRef

Yang R, Wang W (2005) A numerical and experimental study on gap compensation and wavelength selection in UV-lithography of ultra-high aspect ratio SU-8 microstructures. Sens Actuators B Chem 110:279–288CrossRef

Yang L, Shirahata N, Saini G, Zhang F, Pei L, Asplund MC et al (2009) Effect of surface free energy on PDMS transfer in microcontact printing and its application to TOF-SIMS to probe surface energies. Langmuir 25:5674–5683CrossRef

Title: Rapid and low cost replication of complex microfluidic structures with PDMS double casting technology
Authors: Luxia Yang
Xiaojian Hao
Chunshui Wang
Binzhen Zhang
Wanjun Wang
Publication date: 01-10-2014
Publisher: Springer Berlin Heidelberg
Published in: Microsystem Technologies / Issue 10-11/2014
Print ISSN: 0946-7076
Electronic ISSN: 1432-1858
DOI: https://doi.org/10.1007/s00542-013-2004-8

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 10-11/2014

Fabrication of a high aspect ratio (HAR) micropillar filter for a magnetic bead-based immunoassay

A Monte Carlo study of the primary absorbed energy redistribution in X-ray lithography

LIGA micro-openings for coherence characterization of X-rays

IR-drying of photoresists: experimental and theoretical consideration of drying kinetics of mono- and multi-layered coatings

Ferroelectric thin film fabrication by direct UV-lithography

Status of laminar grating manufacturing via lithography at HZB