Top

Journal of Material Cycles and Waste Management

Published in:

19-01-2023 | ORIGINAL ARTICLE

A novel method for preparing phosphorus building gypsum (PBG)-based building materials with low water/gypsum ratios

Authors: Wan Huang, Yunzhi Tan, Huajun Ming, Hui Li, Jun Wu, Chiqiu Wu, Bo Hu

Published in: Journal of Material Cycles and Waste Management | Issue 2/2023

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

It is necessary to consider the dual problems of poor performance and low production efficiency that stem from the highly utilised water/gypsum ratios in the traditional preparation of phosphorus building gypsum (PBG)-based building materials. These problems cannot be easily overcome because that PBG tends to agglomerate at low water/gypsum ratios, which will hinder the hydration process and result in poor mechanical behaviour. In this study, a slurry-particle mixing system was proposed for the preparation of PBG-based building materials with homogeneous hydration at low water/gypsum ratios. More specifically, slurry-particle mixing system samples (SPMS) and pure PBG slurry samples (PPSS) with various water/gypsum ratios were prepared for comparative analysis. The results showed that the fluidity of SPMS with a low water/gypsum ratio could meet the actual production requirements. When compared with the PPSS, the SPMS had a lower water content and a higher dry density at the same water/gypsum ratios. When the water/gypsum ratio was low (e.g., 0.30), the SPMS exhibited more satisfactory moulding behaviour, greater absolutely dry compressive strength, and lower total porosity. In summary, this study presents a feasible method and viable theoretical guideline for the manufacture of PBG-based building materials with low water/gypsum ratios.

previous article Sustainable red ceramic block: recycling of a sewage sludge as raw material

next article Performance evaluation of concrete made with double-processed recycled aggregate (DPRA): mechanical grinding and silica fume impregnation technique

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

Li YB, Dai SB, Zhang YC, Huang J, Su Y, Ma BG (2018) Preparation and thermal insulation performance of cast-in-situ phosphogypsum wall. J. Appl. Biomater. Funct. Mater. 16:81–92

Zheng T, Lu YX, Luo S, Kong DW, Fu RB (2022) Effect of the phosphogypsum calcination time on the compressive mechanical properties of phosphogypsum-based composite cementitious materials. Mat. Res. Express. 9(3):035506CrossRef

Mohammed F, Biswas WK, Yao H, Tadé M (2018) Sustainability assessment of symbiotic processes for the reuse of phosphogypsum. J Clean Prod 188:497–507. https://doi.org/10.1016/j.jclepro.2018.03.309CrossRef

Silva LF, Oliveira ML, Crissien TJ, Santosh M, Bolivar J, Shao LY, Dotto GL, Gasparotto J, Schindler M (2022) A review on the environmental impact of phosphogypsum and potential health impacts through the release of nanoparticles. Chemosphere 286:131513CrossRef

Saadaoui E, Ghazel N, Ben Romdhane C, Massoudi N (2017) Phosphogypsum: potential uses and problems – a review. International J Environ Sci 74(4):558–567. https://doi.org/10.1080/00207233.2017.1330582CrossRef

Jia RQ, Fan YF, Wang Q, Xue JF (2022) Role of NaF on the performances of β-hemihydrate gypsum plaster. J. Build. Eng. 55:104725CrossRef

Zhou J, Li XQ, Zhao Y, Shu Z, Wang YX, Zhang Y, Shen X (2020) Preparation of paper-free and fiber-free plasterboard with high strength using phosphogypsum. Constr Build Mater 243:118091CrossRef

Degirmenci N (2008) Utilization of phosphogypsum as raw and calcined material in manufacturing of building products. Constr Build Mater 22(8):1857–1862. https://doi.org/10.1016/j.conbuildmat.2007.04.024CrossRef

Jin ZH, Ma BG, Su Y, Qi HH, Lu WD, Zhang T (2021) Preparation of eco-friendly lightweight gypsum: Use of beta-hemihydrate phosphogypsum and expanded polystyrene particles. Constr Build Mater 297:123837. https://doi.org/10.1016/j.conbuildmat.2021.123837CrossRef

10.

Ma BG, Jin ZH, Su Y, Lu WD, Qi HH, Hu PH (2020) Utilization of hemihydrate phosphogypsum for the preparation of porous sound absorbing material. Constr Build Mater 234:117346. https://doi.org/10.1016/j.conbuildmat.2019.117346CrossRef

11.

Yu QL, Brouwers HJH (2011) Microstructure and mechanical properties of beta-hemihydrate produced gypsum: An insight from its hydration process. Constr Build Mater 25(7):3149–3157. https://doi.org/10.1016/j.conbuildmat.2010.12.005CrossRef

12.

Padevět P, Tesárek P, Plachý T (2011) Evolution of mechanical properties of gypsum in time. Int J Mech 5(1):1–9

13.

Qu L, Zhao SN, Li J, Guo L (2012) Effect of superplasticizer on the mechanical properties of beta-half-water FGD gypsum under lower ratio of water to gypsum. Bull Chin Ceram Soc 31(3):549–552 ((in Chinese))

14.

Han YW (2019) Phosphogypsum-based construction gypsum modification and yield evaluation. Dissertation, Kunming University of Science and Technology (in Chinese)

15.

Li XL (2016) Study on preparation and properties of phosphogypsum based sound absorption material. Dissertation, Wuhan University of Technology (in Chinese)

16.

Zhang YR, Kong XM, Lu ZB, Lu ZC, Hou SS (2015) Effects of the charge characteristics of polycarboxylate superplasticizers on the adsorption and the retardation in cement pastes. Cem Concr Res 67:184–196. https://doi.org/10.1016/j.cemconres.2014.10.004CrossRef

17.

Van Damme H (2018) Concrete material science: Past, present, and future innovations. Cem Concr Res 112:5–24. https://doi.org/10.1016/j.cemconres.2018.05.002CrossRef

18.

Plank J, Sakai E, Miao CW, Yu C, Hong JX (2015) Chemical admixtures—Chemistry, applications and their impact on concrete microstructure and durability. Cem Concr Res 78:81–99. https://doi.org/10.1016/j.cemconres.2015.05.016CrossRef

19.

Wu PT, Wu CQ, Liu ZX, Hao H (2019) Investigation of shear performance of UHPC by direct shear tests. Eng Struct 183:780–790. https://doi.org/10.1016/j.engstruct.2019.01.055CrossRef

20.

Shi Y, Long GC, Ma C, Xie YJ, He JH (2019) Design and preparation of ultra-high performance concrete with low environmental impact. J Clean Prod 214:633–643. https://doi.org/10.1016/j.jclepro.2018.12.318CrossRef

21.

Zhang YR, Kong XM (2015) Correlations of the dispersing capability of NSF and PCE types of superplasticizer and their impacts on cement hydration with the adsorption in fresh cement pastes. Cem Concr Res 69:1–9. https://doi.org/10.1016/j.cemconres.2014.11.009CrossRef

22.

Pundir A, Garg M, Singh R (2015) Evaluation of properties of gypsum plaster-superplasticizer blends of improved performance. J Build Eng 4:223–230. https://doi.org/10.1016/j.jobe.2015.09.012CrossRef

23.

Jansen D, Neubauer J, Goetz-Neunhoeffer F, Haerzschel R, Hergeth WD (2012) Change in reaction kinetics of a Portland cement caused by a superplasticizer—Calculation of heat flow curves from XRD data. Cem Concr Res 42(2):327–332. https://doi.org/10.1016/j.cemconres.2011.10.005CrossRef

24.

Zhang B, Zheng GY, Liu JN, Xiong RB, Han YW, Xia JP, Yang J (2020) Effect of water reducing agent on properties of phosphogypsum based building gypsum. Bull Chin Ceram Soc 39(5):1540–1546 ((in Chinese))

25.

Li LB, Zhang HM, Guo XY, Zhou XG, Lu LC, Chen MX, Cheng X (2019) Pore structure evolution and strength development of hardened cement paste with super low water-to-cement ratios. Constr Build Mater 227:1–13. https://doi.org/10.1016/j.conbuildmat.2019.117108CrossRef

26.

Shen YQ, Deng M, Lu AQ (2011) Structural evolution of hydrated cement compacts. Mater Struct 44:1735–1743. https://doi.org/10.1617/s11527-011-9731-zCrossRef

27.

Shen YQ, Deng M (2012) Nanostructure of hardened cement compacts cured under sealed and saturated curing conditions. J Chin Ceram Soc 40(12):1699–1702

28.

Zhang X, Liu H, Zhang H (2019) Optimization of air-entrained effect of polycarboxylate superplasticizer. J Build Mater 22(6):957–962

29.

Fu X (2015) Compounding technology of polycarboxylate superplasticizer and the application in engineering. Dissertation, Shijiazhuang: Shijiazhuang Tiedao University (in Chinese)

30.

Muhammad F, Huang X, Li S, Xia M, Zhang ML, Liu Q, Hassan MAS, Jiao BQ, Yu L, Li DW (2018) Strength evaluation by using polycarboxylate superplasticizer and solidification efficiency of Cr⁶⁺, Pb²⁺ and Cd²⁺ in composite based geopolymer. J Clean Prod 188:807–815. https://doi.org/10.1016/j.jclepro.2018.04.033CrossRef

31.

Zivica V, Palou MT, Bagel TIL (2014) High strength metahalloysite based geopolymer. Compos B 57:155–165. https://doi.org/10.1016/j.compositesb.2013.09.034CrossRef

32.

GB/T 9776–200: Calcined gypsum, Standardization Administration of the People’s Republic of China, Beijing. China (in Chinese)

33.

Ertel KD, Carstensen JT (1988) Chemical, physical, and lubricant properties of magnesium stearate. J Pharm Sci 77(7):625–629. https://doi.org/10.1002/jps.2600770715CrossRef

34.

Frederiksen N, Wanheim T (1985) Development of friction tests for lubrication in model-material experiments. J Mech Wkg Technol 12(2):261–268. https://doi.org/10.1016/0378-3804(85)90141-xCrossRef

35.

GB/T 17669.3–1999: Gypsum plasters—Determination of mechanical properties, Standardization Administration of the People’s Republic of China, Beijing. China (in Chinese).

36.

GB/T 17669.4–1999: Gypsum plasters—Determination of physical properties, Standardization Administration of the People’s Republic of China, Beijing, China (in Chinese).

37.

Wu J, Liu L, Deng Y, Zhang G, Zhou A, Xiao H (2022) Use of recycled gypsum in the cement-based stabilization of very soft clays and its micro-mechanism. J Rock Mech Geotech Eng 14(3):909–921. https://doi.org/10.1016/j.jrmge.2021.10.002

38.

Amathieu L, Boistelle R (1986) Improvement of the mechanical properties of set plasters by means of four organic additives inducing 101 faces. J Cryst Growth 79(1–3):169–177. https://doi.org/10.1016/0022-0248(86)90432-xCrossRef

39.

Bumanis G, Zorica J, Bajare D, Korjakins A (2019) Effect of water-binder ratio on properties of phosphogypsum binder[C]//IOP conference series: materials science and engineering. IOP Publishing. 660(1):012071. https://doi.org/10.1088/1757-899X/660/1/012071CrossRef

40.

Singh M, Garg M (1996) Relationship between mechanical properties and porosity of water-resistant gypsum binder. Cem Concr Res 26(3):449–456. https://doi.org/10.1016/S0008-8846(96)85032-0CrossRef

41.

Nor SZM, Ismail R, Isa MIN (2015) Porosity and strength properties of gypsum bonded investment using terengganu local silica for copper alloys casting. J Eng Sci Tech 10(7):921–931

42.

Li ZX, Xu KD, Peng JH, Wang JN, Zhang JW, Li QX (2021) Influence of the heating temperature and fineness on the hydration and mechanical property of recycled gypsum plaster. Adv Mater Sci Eng. https://doi.org/10.1155/2021/7520378CrossRef

43.

Wu J, Liu S, Deng Y, Zhang G, Zhan L (2022) Microscopic phase identification of cement-stabilized clay by nanoindentation and statistical analytics. Appl Clay Sci 224:106531. https://doi.org/10.1016/j.clay.2022.106531

Title: A novel method for preparing phosphorus building gypsum (PBG)-based building materials with low water/gypsum ratios
Authors: Wan Huang
Yunzhi Tan
Huajun Ming
Hui Li
Jun Wu
Chiqiu Wu
Bo Hu
Publication date: 19-01-2023
Publisher: Springer Japan
Published in: Journal of Material Cycles and Waste Management / Issue 2/2023
Print ISSN: 1438-4957
Electronic ISSN: 1611-8227
DOI: https://doi.org/10.1007/s10163-023-01595-x

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 2/2023

Life cycle inventory of recycled aggregates derived from construction and demolition waste

Characterization of Cu2+ adsorption for eco-hydroxyapatite derived from limestone sludge via hydrothermal synthesis

Effects of heating rate and temperature on product distribution of poly-lactic acid and poly-3-hydroxybutyrate-co-3-hydroxyhexanoate

Cobalt extraction from spent lithium-ion battery cathode material using a sulfuric acid solution containing SO2

Advances in the application of crop residues as aggregates and cementing materials in concrete

Evaluating the strength development of mortar using clinker fine aggregate with a combination of fly ash and its inhibitory effects on alkali–silica reaction and delayed ettringite formation