Top

Journal of Materials Engineering and Performance

Published in:

08-11-2021

Effect of Single-Pass Large-Strain Rolling on Microstructure and Mechanical Properties of Al-3Li-1Cu-0.2Er-0.1Zr Alloy

Published in: Journal of Materials Engineering and Performance | Issue 4/2022

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

Effect of single-pass large-strain rolling (LSR) on microstructure and mechanical properties of Al-3Li-1Cu-0.2Er-0.1Zr alloy were investigated. After LSR process at 500 °C with three different reductions (66.7, 75.0, and 83.3%), the residual Cu-rich phases along the grain boundaries were broken and homogeneously distributed. Massive nano-particles of Al₃Li, Al₃(Er, Zr), and Al₃(Er, Zr, Li) precipitated after LSR process. However, with the increase of LSR reduction, the microstructural inhomogeneity was increasingly obvious and massive recrystallized grains were gradually observed. Both strength and ductility were improved after LSR process at 500 °C. After LSR process with 75.0% reduction at three different temperatures (400, 450, and 500 °C), with the increase of LSR temperature, some fine grains were observed near the fibrous grains. Under the condition of LSR process with 75.0% reduction at 450 °C, the best mechanical properties were obtained, with the ultimate tensile strength of 348 MPa and elongation of 19.1%.

previous article Investigating Growth of Iron Borides with the Formation of Monolithic Fe2B Layer on AISI 304 Stainless Steel via Cathodic Reduction and Thermal Diffusion-Based Boriding

next article Role of Heat Input and Ti Addition on Microstructure Evolution, Mechanical Property, and Corrosion Behavior of Welded Joint Produced by Hybrid Laser-Arc Welding of High-Strength Low Alloy Steel

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

A.A. Ei-Aty, Y. Xu, X.Z. Guo, S.H. Zhang, Y. Ma and D.Y. Chen, Strengthening Mechanisms, Deformation Behavior and Anisotropic Mechanical Properties of Al-Li Alloys: A Review, J. Adv. Res., 2018, 10, p 49–67. CrossRef

Y. Wang, R.Z. Wu, N. Turakhodjaev and M.D. Liu, Microstructural Evolution, Precipitation Behavior and Mechanical Properties of a Novel Al-Zn-Mg-Cu-Li-Sc-Zr Alloy, J. Mater. Res., 2021, 36, p 740–750. CrossRef

J.J. Xu, Y.L. Deng, J.Q. Chen, Y.K. Xie, X.B, Guo, Effect of Ageing Treatments on the Precipitation Behavior and Mechanical Properties of Al-Cu-Li Alloys, Mater. Sci. Eng. A 773 (2020) 138885.

Y. Wang, S. Zhang, R.Z. Wu, N. Turakhodjaev, L.G. Hou, J.H. Zhang and S. Betsofen, Coarsening Kinetics and Strengthening Mechanisms of Core-Shell Nanoscale Precipitates in Al-Li-Yb-Er-Sc-Zr Alloy, J. Mater. Sci. Technol., 2021, 61, p 197–203. CrossRef

Y. Wang, S. Zhang, R.Z. Wu, N. Turakhodjaev, J.H. Zhang, M.D. Liu and S. Mardonakulov, Concurrently Improving Uniform Elongation and Strength of Ultrafine-Grained Al-2Li Alloy, Mater. Sci. Eng. A, 2020, 792, p 139848. CrossRef

C. Monachon, D.C. Dunand and D.N. Seidman, Atomic-Scale Characterization of Aluminum-Based Multishell Nanoparticles Created by Solid-State Synthesis, Small, 2010, 16, p 1728–1731. CrossRef

C. Monachon, M.E. Krug, D.N. Seidman, D.C. Dunand, Chemistry and Structure of Core/Double-Shell Nanoscale Precipitates in Al-6.5Li-0.07Sc-0.02Yb (at.%), Acta Mater. 59 (2011) 3398-3409.

J.R. Bowen, T. Masui, N. Tsuji, Microstructure Evolution after Large Strain Deformation in Al-0.13%Mg, Trans Tech Publications. 550 (2007) 235-240.

H.P. Zheng, R.Z. Wu, L.G. Hou, J.H. Zhang, M.L. Zhang, Mathematical Analysis and Its Experimental Comparisons for the Accumulative Roll Bonding (ARB) Process with Different Superimposed Layers, J. Magnes. Alloy. 2020.

10.

X.H. Feng, Y.P. Sun, S.P. Zhou and J.M. He, Influence of Strain Rate on Microstructures and Mechanical Properties of 2524Al Alloy Fabricated by a Novel Large Strain Rolling, Mater. Res. Express, 2020, 7, p 026519. CrossRef

11.

F. Guo, D.F. Zhang, X.W. Fan, L.Y. Jiang, D.L. Yu and F.S. Pan, Deformation Behavior of AZ31 Mg Alloys Sheet During Large Strain Hot Rolling Process: A Study on Microstructure and Texture Evolutions of an Intermediate-Rolled Sheet, J. Alloys Compd., 2016, 663, p 140–147. CrossRef

12.

R.S. Chen, M. Li, S. Du, H.C. Pan, Y.J. Liu, M.Q. Gao, X.S. Zhang, Q.Y. Huang C.L. Yang, L.F. Ma, G.W. Qin, Effects of Single-Pass Large-Strain Rolling on Microstructure and Mechanical Properties of Mg-Al-Ca Alloy Sheet, Mater. Sci. Eng. A 786 (2020) 139332.

13.

H.Y. Wang, Z.P. Yu, L. Zhang, C.G. Liu, M. Zha, C. Wang and Q.C. Jiang, Achieving High Strength and High Ductility in Magnesium Alloy Using Hard-Plate Rolling (HPR) Process, Sci. Rep., 2015, 5, p 1–9.

14.

X.L. Zhang, L. Zhang, G.H. Wu, J.W. Sun, M. Rong, C.C Hsieh, Y.X. Yu, Influence of Sc Content on the Microstructure and Mechanical Properties of Cast Al-2Li-2Cu-0.5Mg-0.2Zr Alloy, Mater. Charact. 142 (2018) 223–236.

15.

T.B. Yu, N. Hansen and X.X. Huang, Linking Recovery and Recrystallization Through Triple Junction Motion in Aluminum Cold Rolled to a Large Strain, Acta Mater., 2013, 61, p 6577–6586. CrossRef

16.

P.F. Wu, Y.L. Deng, J. Zhan, S.T. Fan and X.M. Zhang, The Effect of Inhomogeneous Microstructures on Strength and Fatigue Properties of an Al-Cu-Li Thick Plate, Mater. Sci. Eng. A, 2018, 731, p 1–11. CrossRef

17.

V. Radmilovic, C. Ophus, E.A. Marquis, M.D. Rossell, A. Tolley, A. Gautam, M. Asta and U. Dahmen, Highly Monodisperse Core-Shell Particles Created by Solid-State Reactions, Nat. Mater., 2011, 10, p 710–715. CrossRef

18.

C.M. Zhang, D.F. Yin, Y. Jiang and Y.R. Wang, Precipitation of L1₂-Phase Nano-particles in Dilute Al-Er-Zr Alloys from the First-Principles, Comp. Mater. Sci., 2019, 162, p 171–177. CrossRef

19.

T.F. Yu, B.C. Li, A. Medjahed, L.G. Hou, R.Z. Wu, J.H. Zhang, J.F. Sun and M.L. Zhang, Impeding Effect of the Al3(Er, Zr, Li) Particles on Planar Slip and Intergranular Fracture Mechanism of Al-3Li-1Cu-0.1Zr-X Alloys, Mater. Charact., 2019, 147, p 146–154. CrossRef

20.

C.C. Shi, L. Zhang, G.H. Wu, X.L. Zhang, A.T. Chen and J.S. Tao, Effects of Sc Addition on the Microstructure and Mechanical Properties of Cast Al-3Li-1.5Cu-0.15Zr Alloy, Mater. Sci. Eng. A, 2017, 680, p 232–238. CrossRef

21.

A.T. Chen, G.H. Wu, L. Zhang, X.L. Zhang, C.C. Shi and Y.L. Li, Microstructural Characteristics and Mechanical Properties of Cast Al-3Li-xCu-0.2Zr alloy, Mater. Sci. Eng. A, 2016, 677, p 29–40. CrossRef

22.

P.F. Wu, Y.L. Deng, J. Zhang, S.T. Fan and X.M. Zhang, The Effect of Inhomogeneous Microstructures on Strength and Fatigue Properties of an Al-Cu-Li Thick Plate, Mater. Sci. Eng. A, 2018, 731, p 1–11. CrossRef

23.

Y.L. Ma, J.F. Li, R.Z. Zhang, J.G. Tang, C. Huang, H.Y. Li and Z.Q. Zheng, Strength and Structure Variation of 2195 Al-Li Alloy Caused by Different Deformation Processes of Hot Extrusion and Cold-Rolling, Trans. Nonferrous Met. Soc. China, 2020, 30, p 835–849. CrossRef

24.

O. Engler and K. Lücke, Influence of the Precipitation State on the Cold Rolling Texture in 8090 Al-Li Material, Mater. Sci. Eng. A, 1991, 148, p 15–23. CrossRef

25.

Q. Contrepois, C. Maurice and J.H. Driver, Hot Rolling Textures of Al-Cu-Li and Al-Zn-Mg-Cu Aeronautical Alloys: Experiments and Simulations to High Strains, Mater. Sci. Eng. A, 2010, 527, p 7305–7312. CrossRef

26.

D.G. Cram, X.Y. Fang, H.S. Zuro, Y.J.M. Brechet and C.R. Hutchinson, The Effect of Solute on Discontinuous Dynamic Recrystallization, Acta Mater., 2012, 60, p 6390–6404. CrossRef

27.

S.H. Huan, D.Y. Shu, C.K. Hu and S.F. Zhu, Effect of Strain Rate and Deformation Temperature on Strain Hardening and Softening Behavior of Pure Copper, Trans. Nonferrous Met. Soc. China, 2016, 26, p 1044–1054. CrossRef

28.

C. Shi, J. Lai and X.G. Chen, Microstructural Evolution and Dynamic Softening Mechanisms of Al-Zn-Mg-Cu Alloy During Hot Compressive Deformation, Materialia, 2014, 7, p 244–264. CrossRef

Title: Effect of Single-Pass Large-Strain Rolling on Microstructure and Mechanical Properties of Al-3Li-1Cu-0.2Er-0.1Zr Alloy
Publication date: 08-11-2021
Published in: Journal of Materials Engineering and Performance / Issue 4/2022
Print ISSN: 1059-9495
Electronic ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-021-06385-w

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 4/2022

Role of Initial Surface Roughness in Different Oxidation Stages of TP347H at 700 °C

Effects of Plastic Deformation and Aging Treatment on Phase Precipitation in Ti2AlNb Alloy

Durable Coating with Modified Graphene Oxide for Aircraft Structural CIC Application

Interactions in the Interface Between Coal Ash and Al2O3 Substrate at High Temperatures Induced by the Addition of CaO

An Investigation on Microstructures and Mechanical Properties of Twinning-Induced Plasticity Steels Prepared by Directional Solidification

Effect of V Content on Phase Formation and Mechanical Properties of the CoFeNiMnVx High-Entropy Alloys

Premium Partners