Top

Journal of Materials Engineering and Performance

Published in:

02-01-2019

Enhanced Surface Properties and Microstructure Evolution of Cr12MoV Using Ultrasonic Surface Rolling Process Combined with Deep Cryogenic Treatment

Authors: Shuai Ren, Yunfei Zhang, Yingli Zhao, Zhiguo An, Feng Xue, Jitan Yao, Zhiyan Sun, Jinbao Chang

Published in: Journal of Materials Engineering and Performance | Issue 2/2019

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

In this study, the enhanced surface properties and microstructure evolution of quenched and tempered cold work die steel Cr12MoV, which were induced by ultrasonic surface rolling process combined with deep cryogenic treatment (UDCT), were systematically investigated. The results indicated that UDCT had an advantage over conventional ultrasonic surface rolling process (USRP) in improving surface mechanical properties, including smaller surface roughness and smoother machined surface with less cracks and defects; higher surface microindentation hardness with the value of ~ 890 HV (increased by ~ 6.2% compared with USRP); and lower friction coefficient. Such enhancements in surface properties are mainly attributed to the martensitic transformation of retained austenite, the dispersion strengthening of small secondary carbides and the homogenized carbides distribution during UDCT.

previous article Study on Interfacial Phenomena in Aluminum–Aluminum Bimetal Fabricated by Extrusion at Different Temperatures

next article Creep Behavior of Commercially Pure Titanium TA2 After Supersonic Fine Particles Bombardment

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

Z.B. Wang, N.R. Tao, S. Li, W. Wang, G. Liu, J. Lu, and K. Lu, Effect of Surface Nanocrystallization on Friction and Wear Properties in Low Carbon Steel, Mater. Sci. Eng., A, 2003, 352(1–2), p 144–149CrossRef

L.L. Shaw, Enhanced Fatigue Resistance of a Nickel-Based Hastelloy Induced by a Surface Nanocrystallization and Hardening Process, Philos. Mag. Lett., 2005, 85(8), p 427–438CrossRef

G. Li, S.G. Qu, Y.X. Pan, and X.Q. Li, Effects of the Different Frequencies and Loads of Ultrasonic Surface Rolling on Surface Mechanical Properties and Fretting Wear Resistance of HIP Ti-6Al-4V alloy, Appl. Surf. Sci., 2016, 389, p 324–334CrossRef

X.J. Cao, Y.S. Pyoun, and R. Murakami, Fatigue Properties of a S45C Steel Subjected to Ultrasonic Nanocrystal Surface Modification, Appl. Surf. Sci., 2010, 256(21), p 6297–6303CrossRef

A. Amanov, I.S. Cho, and Y.S. Pyun, Microstructural Evolution and Surface Properties of Nanostructured Cu-Based Alloy by Ultrasonic Nanocrystalline Surface Modification Technique, Appl. Surf. Sci., 2016, 388, p 185–195CrossRef

A. Amanov, J.H. Kim, Y.S. Pyun, T. Hirayama, and M. Hino, Wear Mechanisms of Silicon Carbide Subjected to Ultrasonic Nanocrystalline Surface Modification Technique, Wear, 2014, 332–333, p 891–899

T. Wang, D. Wang, G. Liu, B. Gong, and N. Song, Investigations on the Nanocrystallization of 40Cr Using Ultrasonic Surface Rolling Processing, Appl. Surf. Sci., 2008, 255(5), p 1824–1829CrossRef

H.W. Huang, Z.B. Wang, J. Lu, and K. Lu, Fatigue Behaviors of AISI, 316L Stainless Steel with a Gradient Nanostructured Surface Layer, Acta Mater., 2015, 87, p 150–160CrossRef

A.V. Panin, M.S. Kazachenok, A.I. Kozelskaya, R.R. Hairullin, and E.A. Sinyakova, Mechanisms of Surface Roughening of Commercial Purity Titanium During Ultrasonic Impact Treatment, Mater. Sci. Eng., A, 2015, 647, p 43–50CrossRef

10.

H. Wang, G. Song, and G. Tang, Effect of Electropulsing on Surface Mechanical Properties and Microstructure of AISI, 304 Stainless Steel During Ultrasonic Surface Rolling Process, Mater. Sci. Eng., A, 2016, 662, p 456–467CrossRef

11.

Z. Sun, H. Wang, Y. Ye, Z. Xu, and G. Tang, Effects of Electropulsing on the Machinability and Microstructure of GH4169 Superalloy During Turning Process, Int. J. Adv. Manuf. Technol., 2018, 95(5–8), p 2835–2842CrossRef

12.

X. Li, F. Wang, X. Li, G. Tang, and J. Zhu, Improvement of Formability of Mg-3Al-1Zn Alloy Strip by Electroplastic-Differential Speed Rolling, Mater. Sci. Eng., A, 2014, 618, p 500–504CrossRef

13.

J. Kuang, X. Du, X. Li, Y. Yang, A.A. Luo, and G. Tang, Athermal Influence of Pulsed Electric Current on the Twinning Behavior of Mg-3Al-1Zn Alloy During Rolling, Scripta Mater., 2016, 114, p 151–155CrossRef

14.

R. Zhu, G. Tang, S. Shi, and M. Fu, Effect of Electroplastic Rolling on Deformability and Oxidation of NiTiNb Shape Memory Alloy, J. Mater. Process. Technol., 2013, 213(1), p 30–35CrossRef

15.

Q. Xu, L. Guan, Y. Jiang, G. Tang, and S. Wang, Improved Plasticity of Mg-Al-Zn Alloy by Electropulsing Tension, Mater. Lett., 2010, 64(9), p 1085–1087CrossRef

16.

R.S. Qin, A. Rahnama, W.J. Lu, X.F. Zhang, and B. Elliottbowman, Electropulsed Steels, Mater. Sci. Technol., 2014, 30(9), p 1040CrossRef

17.

H. Li, W. Tong, J. Cui, H. Zhang, L. Chen, and L. Zuo, The Influence of Deep Cryogenic Treatment on the Properties of High-Vanadium Alloy Steel, Mater. Sci. Eng., A, 2016, 662, p 356–362CrossRef

18.

D. Das, A.K. Dutta, and K.K. Ray, Sub-Zero Treatments of AISI, D2 Steel: Part I. Microstructure and Hardness, Mater. Sci. Eng., A, 2010, 527(9), p 2182–2193CrossRef

19.

D. Das, A. Dutta, and K. Ray, On the Refinement of Carbide Precipitates by Cryotreatment in AISI, D2 Steel, Phil. Mag., 2009, 89(1), p 55–76CrossRef

20.

Y. He, K. Yang, W. Qu, F. Kong, and G. Su, Strengthening and Toughening of a 2800-MPa Grade Maraging Steel, Mater. Lett., 2002, 56(5), p 763–769CrossRef

21.

F.J.D. Silva, S.D. Franco, Á.R. Machado, E.O. Ezugwu, and A.M.S. Jr., Performance of Cryogenically Treated HSS Tools, Wear, 2006, 261(5), p 674–685CrossRef

22.

S. Zhirafar, A. Rezaeian, and M. Pugh, Effect of Cryogenic Treatment on the Mechanical Properties of 4340 Steel, J. Mater. Process. Technol., 2007, 186(1–3), p 298–303CrossRef

23.

V. Leskovšek, M. Kalin, and J. Vižintin, Influence of Deep-Cryogenic Treatment on Wear Resistance of Vacuum Heat-Treated HSS, Vacuum, 2006, 80(6), p 507–518CrossRef

24.

H. Liu, J. Wang, H. Yang, and B. Shen, Effects of Cryogenic Treatment on Microstructure and Abrasion Resistance of CrMnB High-Chromium Cast Iron Subjected to Sub-critical Treatment, Mater. Sci. Eng., A, 2008, 478(1–2), p 324–328CrossRef

25.

K.S. Ayl Yong and M. Rahman, Performance Evaluation of Cryogenically Treated Tungsten Carbide Tools in Turning, Int. J. Mach. Tools Manuf, 2006, 46(15), p 2051–2056CrossRef

26.

M. Preciado, P.M. Bravo, and J.M. Alegre, Effect of Low Temperature Tempering Prior Cryogenic Treatment on Carburized Steels, J. Mater. Process. Technol., 2006, 176(1), p 41–44CrossRef

27.

K. Amini, S. Nategh, and A. Shafyei, Influence of Different Cryotreatments on Tribological Behavior of 80CrMo12 5 Cold Work Tool Steel, Mater. Des., 2010, 31(10), p 4666–4675CrossRef

28.

R. Thornton, T. Slatter, A.H. Jones, and R. Lewis, The Effects of Cryogenic Processing on the Wear Resistance of Grey Cast Iron Brake Discs, Wear, 2011, 271(9–10), p 2386–2395CrossRef

29.

A. Molinari, M. Pellizzari, S. Gialanella, G. Straffelini, and K.H. Stiasny, Effect of Deep Cryogenic Treatment on the Mechanical Properties of Tool Steels, J. Mater. Process. Technol., 2001, 118(1–3), p 350–355CrossRef

30.

Y. Dong, X.P. Lin, and H.S. Xiao, Deep Cryogenic Treatment of High-Speed Steel and Its Mechanism, Heat Treat. Met., 1998, 25(3), p 55–59

31.

W. Zhuang, Q. Liu, R. Djugum, P.K. Sharp, and A. Paradowska, Deep Surface Rolling for Fatigue Life Enhancement of Laser Clad Aircraft Aluminium Alloy, Appl. Surf. Sci., 2014, 320(320), p 558–562CrossRef

32.

H. Wang, G. Song, and G. Tang, Evolution of Surface Mechanical Properties and Microstructure of Ti 6Al 4 V Alloy Induced by Electropulsing-Assisted Ultrasonic Surface Rolling Process, J. Alloy. Compd., 2016, 681, p 146–156CrossRef

33.

H. Wang, G. Song, and G. Tang, Enhanced Surface Properties of Austenitic Stainless Steel by Electropulsing-Assisted Ultrasonic Surface Rolling Process, Surf. Coat. Technol., 2015, 282, p 149–154CrossRef

34.

N.B. Dhokey and P.K. Lalge, Influence of Cryosoaking Period on Wear Characteristics and Surface Topography of M35 Tool Steel, Tribol. Mater. Surf. Interfaces, 2018, 12, p 170–175CrossRef

35.

H. Torkamani, S. Raygan, and J. Rassizadehghani, Comparing Microstructure and Mechanical Properties of AISI, D2 Steel After Bright Hardening and Oil Quenching, Mater. Des., 2014, 54, p 1049–1055CrossRef

36.

J.Y. Huang, Y.T. Zhu, H. Jiang, and T.C. Lowe, Microstructures and Dislocation Configurations in Nanostructured Cu Processed by Repetitive Corrugation and Straightening, Acta Mater., 2001, 49(9), p 1497–1505CrossRef

37.

K. Lu and J. Lu, Nanostructured Surface Layer on Metallic Materials Induced by Surface Mechanical Attrition Treatment, Mater. Sci. Eng., A, 2004, 375–377(1), p 38–45CrossRef

38.

X.C. Liu, H.W. Zhang, and K. Lu, Strain-Induced Ultrahard and Ultrastable Nanolaminated Structure in Nickel, Science, 2013, 342(6156), p 337–340CrossRef

39.

N.A. Mara, A.V. Sergueeva, T.D. Mara, S.X. Mcfadden, and A.K. Mukherjee, Superplasticity and Cooperative Grain Boundary Sliding in Nanocrystalline Ni3Al, Mater. Sci. Eng., A, 2007, 463(1), p 238–244CrossRef

40.

S. Ren, Z. Sun, Z. Xu, R. Xin, J. Yao, D. Lv, and J. Chang, Effects of Twins and Precipitates at Twin Boundaries on Hall-Petch Relation in High Nitrogen Stainless Steel, J. Mater. Res., 2018, 33(12), p 1764–1772CrossRef

41.

H.G. Nanesa, J. Boulgakoff, and M. Jahazi, Influence of Prior Cold Deformation on Microstructure Evolution of AISI, D2 Tool Steel After Hardening Heat Treatment, J. Manuf. Process, 2016, 22, p 115–119CrossRef

42.

M.A. Hamidzadeh, M. Meratian, and M.M. Zahrani, A Study on the Microstructure and Mechanical Properties of AISI, D2 Tool Steel Modified by Niobium, Mater. Sci. Eng., A, 2010, 556(12), p 758–766

43.

S. Li, Y. Xie, and X. Wu, Hardness and Toughness Investigations of Deep Cryogenic Treated Cold Work Die Steel, Cryogenics, 2010, 50(2), p 89–92CrossRef

44.

M. Pérez and F.J. Belzunce, The Effect of Deep Cryogenic Treatments on the Mechanical Properties of an AISI, H13 Steel, Mater. Sci. Eng., A, 2015, 624, p 32–40CrossRef

45.

T.V. Pirtovšek, G. Kugler, and M. Terčelj, The Behaviour of the Carbides of Ledeburitic AISI, D2 Tool Steel During Multiple Hot Deformation Cycles, Mater. Charact., 2013, 83(3), p 97–108CrossRef

46.

D. Senthilkumar, I. Rajendran, M. Pellizzari, and J. Siiriainen, Influence of Shallow and Deep Cryogenic Treatment on the Residual State of Stress of 4140 Steel, J. Mater. Process. Technol., 2011, 211(3), p 396–401CrossRef

47.

K. Amini, A. Akhbarizadeh, and S. Javadpour, Investigating the Effect of Holding Duration on the Microstructure of 1.2080 Tool Steel During the Deep Cryogenic Heat Treatment, Vacuum, 2012, 86(10), p 1534–1540CrossRef

48.

A.I. Tyshchenko, W. Theisen, A. Oppenkowski, S. Siebert, O.N. Razumov, A.P. Skoblik, V.A. Sirosh, Y.N. Petrov, and V.G. Gavriljuk, Low-Temperature Martensitic Transformation and Deep Cryogenic Treatment of a Tool Steel, Mater. Sci. Eng., A, 2010, 527(26), p 7027–7039CrossRef

49.

P. Jurči, M. Dománková, Ľ. Čaplovič, J. Ptačinová, J. Sobotová, P. Salabová, O. Prikner, B. Šuštaršič, and D. Jenko, Microstructure and Hardness of Sub-Zero Treated and No Tempered P/M Vanadis 6 Ledeburitic Tool Steel, Vacuum, 2015, 111, p 92–101CrossRef

50.

G.A. Fontalvo, R. Humer, C. Mitterer, K. Sammt, and I. Schemmel, Microstructural Aspects Determining the Adhesive Wear of Tool Steels, Wear, 2006, 260(9–10), p 1028–1034CrossRef

Title: Enhanced Surface Properties and Microstructure Evolution of Cr12MoV Using Ultrasonic Surface Rolling Process Combined with Deep Cryogenic Treatment
Authors: Shuai Ren
Yunfei Zhang
Yingli Zhao
Zhiguo An
Feng Xue
Jitan Yao
Zhiyan Sun
Jinbao Chang
Publication date: 02-01-2019
Publisher: Springer US
Published in: Journal of Materials Engineering and Performance / Issue 2/2019
Print ISSN: 1059-9495
Electronic ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-018-3843-3

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 2/2019

Computational Simulation of an Additively Manufactured Marine Component

Improvement of Microstructure and Mechanical Properties of CoCrCuFeNi High-Entropy Alloys By V Addition

Wear Resistance and Tribological Features of Ultra-Fine-Grained Al-Mg Alloys Processed by Constrained Groove Pressing-Cross Route

Defect Characterization Through Automated Laser Track Trace Identification in SLM Processes Using Laser Profilometer Data

Thermo-Fluid Modeling of Selective Laser Melting: Single-Track Formation Incorporating Metallic Powder

A Perspective on Solid-State Additive Manufacturing of Aluminum Matrix Composites Using MELD

Premium Partners