Top

The International Journal of Advanced Manufacturing Technology

Published in:

22-08-2022 | ORIGINAL ARTICLE

Numerical investigation of surface textural dimples of titanium alloy subjected to laser shock processing

Authors: Zhenhua Zhang, Mengjin Liu, Ziwen Cao, Wenlong Zhou, Guoqing Chen, Xuesong Fu

Published in: The International Journal of Advanced Manufacturing Technology | Issue 3-4/2022

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

Laser shock processing is utilized to produce laser dimples by means of mechanical force, with local plastic deformation induced on the material surface. Based on this characteristic, array dimples are prepared to regularly distribute on the treated surface, to manufacture anti-friction surfaces fulfilling service requirements. In the current work, finite element method (FEM) served as an effective method for better understanding the deformation characteristics of the laser-shocked dimple under single-shot and overlapping shot laser shock processing and investigating the influence of laser parameters. The results indicate that the target material experienced unceasing deformation and dynamic elastic recovery during the dynamic response process. The ultimate dimple profile was significantly affected by diverse types of pressure spatial distribution. In addition, the pile-up appeared at the dimple edge, and the reverse deformation near the spot center was more prone to occur in the case of flap-top distribution, which also appeared in the overlapping laser shock. The experimental profiles of laser shock dimples were consistent with the simulation results in the overlapping laser shock, showing that the finite element simulation can be effectively used to design surface textural dimples.

previous article Surface generation on titanium alloy through powder-mixed electric discharge machining with the focus on bioimplant applications

next article Chip wave phase difference analysis of robotic milling and chatter dominant mode research

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

Stout KJ, Blunt L (2001) A contribution to the debate on surface classifications—random, systematic, unstructured, structured and engineered. Int J Mach Tools Manu 41:2039–2044. https://doi.org/10.1016/S0890-6955(01)00069-4CrossRef

Zhou W, Ren X, Yang Y, Tong Z, Larson EA (2019) Finite element analysis of laser shock peening induced near-surface deformation in engineering metals. Opt Laser Technol 119:105608–105608. https://doi.org/10.1016/j.optlastec.2019.105608CrossRef

Guo YB, Caslaru R (2011) Fabrication and characterization of micro dent arrays produced by laser shock peening on titanium Ti–6Al–4V surfaces. J Mater Process Tech 211:729–736. https://doi.org/10.1016/j.jmatprotec.2010.12.007CrossRef

Li KM, Yao ZQ, Hu YX, Guo WB (2014) Friction and wear performance of laser peen textured surface under starved lubrication. Tribol Int 77:97–105. https://doi.org/10.1016/j.triboint.2014.04.017CrossRef

Li K, Wang Y, Yu Z, Hu J (2019) Process mechanism in laser peen texturing artificial joint material. Opt Laser Eng 115:149–160. https://doi.org/10.1016/j.optlaseng.2018.11.013CrossRef

Mao B, Siddaiah A, Liao Y, Menezes PL (2020) Laser surface texturing and related techniques for enhancing tribological performance of engineering materials: a review. J Manuf Process 53:153–173. https://doi.org/10.1016/j.jmapro.2020.02.009CrossRef

Dai F, Lu J, Zhang Y, Luo K, Zhang L, Wang Q, Ren X, Li P (2012) Micro-dent arrays fabricated by a novel net mask laser shock processing on the surface of LY2 aluminum alloy. J Appl Phys 112:023117–023123. https://doi.org/10.1063/1.4740069CrossRef

Qin Y, Xiong D, Li J (2015) Tribological properties of laser surface textured and plasma electrolytic oxidation duplex-treated Ti6Al4V alloy deposited with MoS2 film. Surf Coat Technol 269:266–272. https://doi.org/10.1016/j.surfcoat.2014.12.003CrossRef

Qian S, Di Z, Qu N, Li H, Yan D (2010) Generating micro-dimples array on the hard chrome-coated surface by modified through mask electrochemical micromachining. Int J Adv Manuf Tech 47:1121–1127. https://doi.org/10.1007/s00170-009-2246-xCrossRef

10.

Tao Z, Liu Z, Xu C (2013) Influence of size effect on burr formation in micro cutting. Int J Adv Manuf Tech 68:1911–1917. https://doi.org/10.1007/s00170-013-4801-8CrossRef

11.

Yoo J, Cho JS, Ahn SJ, Gwak J, Cho A, Eo YJ, Yun JH, Yoon K, Yi J (2013) Random reactive ion etching texturing techniques for application of multicrystalline silicon solar cells. Thin Solid Films 546:275–278. https://doi.org/10.1016/j.tsf.2013.02.045CrossRef

12.

Agung SS, Tae JK (2009) A thick SU-8 mask for microabrasive jet machining on glass. Int J Adv Manuf Technol 7–8:734–740. https://doi.org/10.1007/s00170-008-1520-7CrossRef

13.

Prasad KN, Syed I, Subbu SK (2019) Laser dimple texturing – applications, process, challenges, and recent developments: a review. Aust J Mech Eng 2:316–331. https://doi.org/10.1080/14484846.2019.1705533CrossRef

14.

Luo KY, Yao HX, Dai FZ, Lu JZ (2014) Surface textural features and its formation process of AISI 304 stainless steel subjected to massive LSP impacts. Opt Laser Eng 55:136–142. https://doi.org/10.1016/j.optlaseng.2013.10.026CrossRef

15.

Li K, Hu Y, Yao Z (2013) Experimental study of micro dimple fabrication based on laser shock processing. Opt Laser Technol 48:216–225. https://doi.org/10.1016/j.optlastec.2012.09.015CrossRef

16.

Liu H, Huang Z, Gu C, Shen Z, Wang X (2014) Experiment and numerical simulation of laser shock micro dents. Int J Surf Sci Eng 8:57–70. https://doi.org/10.1504/ijsurfse.2014.059311CrossRef

17.

Fang Y, Ji X, Zhang X, Wang J, Chen B, Duan S, Tong J, Fang G, Pei S (2019) Experiment and numerical simulation of micro dent fabricated by laser shocking 2024 aluminum alloy. Multidiscip Model Ma 16:156–168. https://doi.org/10.1108/mmms-04-2019-0076CrossRef

18.

Sun B, Qiao H, Zhao J (2018) Accurate numerical modeling of residual stress fields induced by laser shock peening. AIP Adv 8:95203–95215. https://doi.org/10.1063/1.5039674CrossRef

19.

Li X, He W, Luo S, Nie X, Tian L, Feng X, Li R (2019) Simulation and experimental study on residual stress distribution in titanium alloy treated by laser shock peening with flat-top and Gaussian laser beams. Materials 12:1343–1350. https://doi.org/10.3390/ma12081343CrossRef

20.

Sun R, Li L, Zhu Y, Zhang L, Guo W, Peng P, Li B, Guo C, Liu L, Che Z, Li W, Sun J, Qiao H (2017) Dynamic response and residual stress fields of Ti6Al4V alloy under shock wave induced by laser shock peening. Model Simul Mater Sc 25:065016–065023. https://doi.org/10.1088/1361-651X/aa7a46CrossRef

21.

Li K, Cai Y, Yu Z, Hu J (2020) Formation mechanism of residual stress hole under different pulse durations and shock pressure distributions in Ti6Al4V alloy during laser peen texturing. Opt Laser Technol 130:106361–106368. https://doi.org/10.1016/j.optlastec.2020.106361CrossRef

22.

Wu J, Zhao J, Qiao H, Lu Y, Sun B, Hu X, Yang Y (2020) A method to determine the material constitutive model parameters of FGH4095 alloy treated by laser shock processing. Appl Surf Sci Adv 1:100029. https://doi.org/10.1016/j.apsadv.2020.100029CrossRef

23.

Cao Z, Che Z, Zou S (2013) Simulation study of stress hole on laser shock peening with square spot. Rare Metal Materials and Engineering 42:222–225

24.

Luo KY, Lu JZ, Wang QW, Luo M, Qi H, Zhou JZ (2013) Residual stress distribution of Ti-6Al-4V alloy under different ns-LSP processing parameters. Appl Surf Sci 285:607–615. https://doi.org/10.1016/j.apsusc.2013.08.100CrossRef

25.

Yan H, Qin Z, Zhang W, Ming A, Wang X, Chu F (2019) Dynamic analysis of laser shock response: experimental and numerical studies. Aerosp Sci Technol 94:105430–105439. https://doi.org/10.1016/j.ast.2019.105430CrossRef

26.

Fabbro R, Fournier J, Ballard P, Devaux D, Virmont J (1990) Physical study of laser-produced plasma in confined geometry. J Appl Phys 68:775–784. https://doi.org/10.1063/1.346783CrossRef

27.

Ding K, Ye L (2006) Simulation of multiple laser shock peening of a 35CD4 steel alloy. J Mater Process Tech 178:162–169. https://doi.org/10.1016/j.jmatprotec.2006.03.170CrossRef

28.

Correa C, Ruiz De Lara L, Diaz M, Gil-Santos A, Porro JA, Ocana JL (2015) Effect of advancing direction on fatigue life of 316L stainless steel specimens treated by double-sided laser shock peening. Int J Fatigue 79:1–9. https://doi.org/10.1016/j.ijfatigue.2015.04.018CrossRef

29.

Bhamare S, Ramakrishnan G, Mannava SR, Langer K, Vasudevan VK, Qian D (2013) Simulation-based optimization of laser shock peening process for improved bending fatigue life of Ti-6Al-2Sn-4Zr-2Mo alloy. Surf Coat Tech 232:464–474. https://doi.org/10.1016/j.surfcoat.2013.06.003CrossRef

30.

Wei XL, Ling X (2014) Numerical modeling of residual stress induced by laser shock processing. Appl Surf Sci 301:557–563. https://doi.org/10.1016/j.apsusc.2014.02.128CrossRef

31.

Hu X, Wu J, Zhao J, Yang Y, Qiao H (2020) Numerical simulation of the surface morphology and residual stress field of IN718 alloy by Gaussian mode laser shock. Optik 207:164441–164449. https://doi.org/10.1016/j.ijleo.2020.164441CrossRef

32.

Correa C, Gil-Santos A, Porro JA, Diaz M, Ocana JL (2015) Eigenstrain simulation of residual stresses induced by laser shock processing in a Ti6Al4V hip replacement. Mater Design 79:106–114. https://doi.org/10.1016/j.matdes.2015.04.048CrossRef

33.

Hfaiedh N, Peyre P, Song H, Popa I, Ji V, Vignal V (2015) Finite element analysis of laser shock peening of 2050–T8 aluminum alloy. Int J Fatigue 70:480–489. https://doi.org/10.1016/j.ijfatigue.2014.05.015CrossRef

34.

Zhang X, She J, Li S, Duan S, Zhou Y, Yu X, Zheng R, Zhang B (2015) Simulation on deforming progress and stress evolution during laser shock forming with finite element method. J Mater Process Tech 220:27–35. https://doi.org/10.1016/j.jmatprotec.2015.01.004CrossRef

35.

Vasu A, Hu Y, Grandhi RV (2013) Differences in plasticity due to curvature in laser peened components. Surf Coat Tech 235:648–656. https://doi.org/10.1016/j.surfcoat.2013.08.043CrossRef

36.

Irizalp SG, Saklakoglu N, Akman E, Demir A (2014) Pulsed Nd:YAG laser shock processing effects on mechanical properties of 6061–T6 alloy. Opt Laser Technol 56:273–277. https://doi.org/10.1016/j.optlastec.2013.08.011CrossRef

37.

Ding K, Ye L (2008) Laser shock peening performance and process simulation. Woodhead Publishing, Cambridge

38.

Hu Y, Gong C, Yao Z, Hu J (2009) Investigation on the non-homogeneity of residual stress field induced by laser shock peening. Surf Coat Tech 203:3503–3508. https://doi.org/10.1016/j.surfcoat.2009.04.029CrossRef

Title: Numerical investigation of surface textural dimples of titanium alloy subjected to laser shock processing
Authors: Zhenhua Zhang
Mengjin Liu
Ziwen Cao
Wenlong Zhou
Guoqing Chen
Xuesong Fu
Publication date: 22-08-2022
Publisher: Springer London
Published in: The International Journal of Advanced Manufacturing Technology / Issue 3-4/2022
Print ISSN: 0268-3768
Electronic ISSN: 1433-3015
DOI: https://doi.org/10.1007/s00170-022-09947-x

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 3-4/2022

Numerical investigation of machining of SiC/Al matrix composites by a coupled SPH and FEM

Research progress of surface modification and solid–liquid lubrication synergistic friction reduction and wear resistance

Improvement of circular hole flanging height using multi-directional electromagnetic flanging

Modeling of oxide-film thickness in electrolytic in-process dressing grinding with workpiece swing

Influence of tool pin length and dissimilar material configuration on friction stir lap welding of Al and Mg alloys

Influence of sheet thickness on mechanical behaviors of the clinched joints produced by single-point butt clinching process

Premium Partners