Top

Journal of Materials Engineering and Performance

Published in:

08-10-2021

Investigation into Coating Structure and Wear Environment Effects on Tribological Properties of Piston Ring Coated with Monolayer TiAlN and Multilayer TiN/TiAlN

Authors: Sevim Hamamci Alisir, Dileknur Evrensel

Published in: Journal of Materials Engineering and Performance | Issue 2/2022

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

Friction among different engine components in internal combustion engines affects the life and combustion performance of the engine. Today, different surface coatings are made to reduce these effects. The physical vapor deposition (PVD) method has attracted the most attention because it is environmentally friendly and homogeneous coatings can be obtained. In this paper, tribological and mechanical properties of the monolayer TiAlN (titanium aluminum nitride) and multilayer TiN/TiAlN ceramic coatings applied to the piston rings made of cast iron with PVD method have been reported. In addition, the tribological behavior of the multilayer TiAlN coating was investigated for lubrication and dry conditions. The coating types, wear morphologies, chemical composition and phases on the coating surface were analyzed by SEM, EDS and XRD techniques. As a result of the tribological test, the coefficients of friction of mono- and multilayer TiAlN coatings under dry conditions were determined as 0.60 and 0.45 for 250 m, respectively. According to the result of the tribological test under lubricated environment conditions performed using the same parameters, it was determined that the friction of the multilayer TiAlN coating decreased by 85% (µ = 0.088). As a result, the multilayer TiAlN coated ring showed the best abrasion resistance. The reciprocating sliding test result showed that the wear rate of the multilayer TiAlN coating has been reduced by 95% compared to the uncoated ring. Considering all the experimental findings, it has been proven that as the number of layers in the coating increases, the surface roughness, hardness and wear properties improve. Furthermore, the wear mechanism was suggested to coated specimens based on the SEM image taken from the worn surface of the sample and EDX analysis.

previous article A Non-invasive Technique to Estimate the Onset of Creep Strength Deterioration

next article Influence of Electrolyte Compositions and Electrical Parameters on Thermal Properties of Micro-Arc Oxidized AZ91 Alloy

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

S. Chu and A. Majumdar, Opportunities and Challenges for a Sustainable Energy Future, Nature, 2012, 488, p 294–303. https://doi.org/10.1038/nature11475CrossRef

K. Holmberg, P. Andersson and A. Erdemir, Global Energy Consumption due to Friction in Passenger Cars, Tribol. Int., 2017, 47, p 221–234. https://doi.org/10.1016/j.triboint.2011.11.022CrossRef

J. Fu, J. Liu, B. Deng, J. Yang and R. Feng, A Combined Air Cycle Used for IC Engine Supercharging Based on Waste Heat Recovery, Energy Convers. Manag., 2014, 87, p 86–95. https://doi.org/10.1016/j.enconman.2014.06.097CrossRef

R. Feng, J. Yang, D. Zhang, B. Deng, J. Flu, J. Liu and X. Liu, Experimental Study on SI Engine Fuelled with Butanol–Gasoline Blend and H₂O Addition, Energy Convers. Manag., 2013, 74, p 192–200. https://doi.org/10.1016/j.enconman.2013.05.021CrossRef

K. Holmberg, P. Anderson and A. Erdemir, Global Energy Consumption due to Friction in Passenger Cars, Tribol. Int., 2012, 47, p 221–234. https://doi.org/10.1016/j.triboint.2011.11.022CrossRef

A. Roberts, R. Brooks and P. Shipway, Internal Combustion Engine Cold-Start Efficiency: A Review of the Problem, Causes and Potential Solutions, Energy Convers. Manag., 2014, 82, p 327–350. https://doi.org/10.1016/j.enconman.2014.03.002CrossRef

C. Hanbao, Y. Zhang and L. Chen, Gray Forecast of Diesel Engine Performance Based on Wear, Appl. Therm. Eng., 2003, 23, p 2285–2292. https://doi.org/10.1016/S1359-4311(03)00186-8CrossRef

E. Guzel, C. Yuksel, Y. Bayrak, O. Sen and A. Ekerim, Effect of Section Thickness on the Microstructure and Hardness of Ductile Cast Iron, Mater. Test., 2014, 56, p 285–288. https://doi.org/10.3139/120.110558CrossRef

S. Alisir and S. Cevik, The Effects of Foundry Sand Components on the Cast Iron, Res. Eng. Struct. Mater., 2020, 6, p 127–140. https://doi.org/10.17515/resm2019.148ma0911CrossRef

10.

J.A.G. Sousa, W.F. Sales and A.R. Machado, A Review on the Machining of Cast Iron, Int. J. Adv. Manuf. Technol., 2018, 94, p 4073–4092. https://doi.org/10.1007/s00170-017-1140-1CrossRef

11.

L. Jianliang, R. Wei, D.C. Bitsis and P.M. Lee, Development and Evaluation of Low Friction TiSiCN Nanocomposite Coatings for Piston Ring Applications, Surf. Coat. Technol., 2016, 298, p 121–131. https://doi.org/10.1016/j.surfcoat.2016.04.061CrossRef

12.

N. Masahiko, Trends in Engine Technology and Tribology, Tribol. Int., 1994, 27, p 3–8. https://doi.org/10.1016/0301-679X(94)90056-6CrossRef

13.

N. Dolatabadi, M. Forder, N. Morris, R. Rahmani, H. Rahneja and S. Howell-Smith, Influence of Advanced Cylinder Coatings on Vehicular Fuel Economy and Emissions in Piston Compression Ring Conjunction, Appl. Energy, 2020, 259, p 114–129. https://doi.org/10.1016/j.apenergy.2019.114129CrossRef

14.

W. Shanhong, D. Li, G. Zhang, A.K. Tieu and B. Zhang, Comparison of the Scuffing Behaviour and Wear Resistance of Candidate Engineered Coatings for Automotive Piston Rings, Tribol. Int., 2017, 106, p 10–22. https://doi.org/10.1016/j.triboint.2016.10.026CrossRef

15.

F. Rita, J. Martins, Ó. Carvalho, L. Sobral and F. Silva, Tribological Solutions for Engine Piston Ring Surfaces: An Overview on the Materials and Manufacturing, Mater. Manuf. Process., 2020, 35, p 498–520. https://doi.org/10.1080/10426914.2019.1692352CrossRef

16.

G. Wieslaw, W. Koszela, P. Pawlus and S. Ochwat, Improving Tribological Behaviour of Piston Ring–Cylinder Liner Frictional Pair by Liner Surface Texturing, Tribol. Int., 2013, 61, p 102–108. https://doi.org/10.1016/j.triboint.2012.11.027CrossRef

17.

M. Eid, Performance Analysis and Condition Monitoring of Ice Piston-Ring Based on Combustion and Thermal Characteristics, Appl. Thermal. Eng., 2018, 132, p 824–840. https://doi.org/10.1016/j.applthermaleng.2017.12.111CrossRef

18.

T. Simon and H. Gao, Tribological Characteristics and Surface Interaction Between Piston Ring Coatings and a Blend of Energy-Conserving Oils and Ethanol Fuels, Wear, 2003, 255, p 1276–1285. https://doi.org/10.1016/S0043-1648(03)00240-0CrossRef

19.

I.S. Vinoth, S. Detwal, V. Umasankar and A. Sarma, Tribological Studies of Automotive Piston Ring by Diamond-Like Carbon Coating, Tribol. Mater. Surf. Interfaces, 2019, 13, p 31–38. https://doi.org/10.1080/17515831.2019.1569852CrossRef

20.

T. Ankit, S.M. Pandey, Q. Murtaza, R.S. Walia and M. Tyagi, Tribological Behavior of Carbon Coating for Piston Ring Applications using Taguchi Approach, Mater. Today, 2020, 25, p 759–764. https://doi.org/10.1016/j.matpr.2019.09.004CrossRef

21.

F.S. Silva, Fatigue on Engine Pistons–a Compendium of Case Studies, Eng. Fail. Anal., 2006, 13, p 480–492. https://doi.org/10.1016/j.engfailanal.2004.12.023CrossRef

22.

M. Priest, Factors Influencing Boundary Friction and Wear of Piston Rings, Tribol. Ser., 2000, 38, p 409–416. https://doi.org/10.1016/S0167-8922(00)80145-5CrossRef

23.

Q.M. Mehran, M.A. Fazal, A.R. Bushroa and S. Rubaiee, A Critical Review on Physical Vapor Deposition Coatings Applied on Different Engine Components, Crit. Rev. Solid State Mater. Sci., 2018, 43, p 158–175. https://doi.org/10.1080/10408436.2017.1320648CrossRef

24.

M. Priest and M.T. Christopher, Automobile Engine Tribology—Approaching the Surface, Wear, 2000, 241, p 193–203. https://doi.org/10.1016/S0043-1648(00)00375-6CrossRef

25.

X. Yufu, Q. Zhenga, J. Genga, Y. Dongb, M. Tiana, L. Yaoc and K.D. Dearnd, Synergistic Effects of Electroless Piston Ring Coatings and Nano-Additives ın Oil on the Friction and Wear of a Piston Ring/Cylinder Liner Pair, Wear, 2019, 422, p 201–211. https://doi.org/10.1016/j.wear.2019.01.064CrossRef

26.

S. Arı and Z. Parlar, Measurement Methods of Wear Between Piston Ring and Cylinder Liner, Sigma J. Eng. Natl. Sci., 2013, 31, p 319–334.

27.

E. Bozyazı, M. Urgen and A.F. Çakır, Comparison of Reciprocating Wear Behaviour of Electrolytic Hard Chrome and Arc-PVD CrN Coatings, Wear, 2004, 256, p 832–839. https://doi.org/10.1016/S0043-1648(03)00523-4CrossRef

28.

C. An, X. Qiu, K. Sridharan, W.G. Horne, R.A. Dodd, A.H. Hamdi, A.A. Elmoursi, G.W. Malaczynski and J.R. Condrad, Chromium Plating Pollution Source Reduction by Plasma Source Ion Implantation, Surf. Coat. Tech., 1996, 82, p 305–310. https://doi.org/10.1016/0257-8972(95)02745-9CrossRef

29.

L. Vernhes, M. Azzi and J.E. Klemberg-Sapieha, Alternatives for Hard Chromium Plating: Nanostructured Coatings for Severe-Service Valves, Mater. Chem. Phys., 2013, 140, p 522–528. https://doi.org/10.1016/j.matchemphys.2013.03.065CrossRef

30.

L. Ping, L. Chen, S.Q. Wang, B. Yang, Y. Du, J. Li and M.J. Wu, Microstructure Mechanical and Thermal Properties of TiAlN/CrAlN Multilayer Coatings, Int. J. Refract. Met. Hard Mater., 2013, 40, p 51–57. https://doi.org/10.1016/j.ijrmhm.2013.01.020CrossRef

31.

A. Kulkarni, V. Sargade and C. More, Machinability Investigation of AISI 304 Austenitic a AlTiN/TiAlN Coated Carbide Inserts, Procedia Manuf., 2018, 20, p 548–553. https://doi.org/10.1016/j.promfg.2018.02.082CrossRef

32.

H.A. Jehn, Multicomponent and Multiphase Hard Coatings for Tribological Applications, Surf. Coat. Tech., 2000, 131, p 433–440. https://doi.org/10.1016/S0257-8972(00)00783-0CrossRef

33.

A. Baptista, F. Silva, J. Porteiro, J. Miguez and G. Pinto, Sputtering Physical Vapor Deposition (PVD) Coatings: A Critical Review on Process Improvement and Market Trend Demand, Coatings, 2018, 8, p 402–423. https://doi.org/10.3390/coatings8110402CrossRef

34.

G. Gupta, R.K. Tyagi, S.K. Rajput, P. Saxena, A. Vashisth and S. Mehndiratta, PVD Based Thin Film Deposition Methods and Characterization/Property of Different Compositional Coatings -a Critical Analysis, Mater. Today Proc., 2021, 38, p 259–264. https://doi.org/10.1016/j.matpr.2020.07.132CrossRef

35.

P.V. Moghaddam, B. Prakash, E. Vuorinen, M. Fallqvist, J.M. Andersson and J. Hardell, High Temperature Tribology of TiAlN PVD Coating Sliding Against 316L Stainless Steel and Carbide –Free Bainitic Steel, Tribol. Int., 2021, 159, p 106847. https://doi.org/10.1016/j.triboint.2020.106847CrossRef

36.

F.F. Komarov, V.M. Konstantinov, A.V. Kovalchuk, S.V. Konstantinov and H.A. Tkachenko, The Effect of Steel Substrate Pre-Hardening on Structural, Mechanical and Tribological Properties of Magnetron Sputtered TiN and TiAlN Coatings, Wear, 2016, 352, p 92–101. https://doi.org/10.1016/j.wear.2016.02.007CrossRef

37.

K. Zhang, J. Deng, X. Guo, L. Sun and S. Lei, Study on the Adhesion and Tribological Behavior of PVD TiAlN Coatings with Multi-Scale Textured Substrate Surface, Int. J. Refract. Hard Met., 2018, 72, p 292–305. https://doi.org/10.1016/j.ijrmhm.2018.01.003CrossRef

38.

S. PalDey and S. Deevi, Single Layer and Multilayer Wear Resistant Coatings of (Ti, Al) N: A Review, Mater. Sci. Eng. A, 2003, 342, p 58–79. https://doi.org/10.1016/S0921-5093(02)00259-9CrossRef

39.

G. Skordaris, K.D. Bouzakis, T. Kotsanis, P. Charalampous, E. Bouzakis, O. Lemmer and S. Bolz, Film Thickness Effect on Mechanical Properties and Milling Performance of Nano-Structured Multilayer PVD Coated Tools, Surf. Coat. Tech., 2016, 307, p 452–460. https://doi.org/10.1016/j.surfcoat.2016.09.026CrossRef

40.

V.V. Lyubimov, A.A. Voevodin, A.L. Yerokhin, Y.S. Timofeev and I.K. Arkhipov, Development and Testing of Multilayer Physically Vapour Deposited Coatings for Piston Rings, Surf. Coat. Tech., 1992, 52, p 145–151. https://doi.org/10.1016/0257-8972(92)90040-HCrossRef

41.

Z. Sun, Z. Peijun, Z. Leheng, X. Xinfua, H. Aiminb and Z. Wenquan, Multi-Layer Compound Coating on Cast Iron Piston Ring by Multi-Arc and Magnetron Sputtering ion Compound Plating Technique, Surf. Coat. Tech., 2000, 131, p 422–427. https://doi.org/10.1016/S0257-8972(00)00781-7CrossRef

42.

X. Wang, P.Y. Kwon and D. Schrock, Friction Coefficient and Sliding Wear of AlTiN Coating under Various Lubrication Conditions, Wear, 2013, 304, p 67–76. https://doi.org/10.1016/j.wear.2013.03.050CrossRef

43.

Y.C. Chim, X.Z. Ding, X.T. Zeng and S. Zhang, Oxidation Resistance of TiN, CrN, TiAlN and CrAlN Coatings Deposited by Lateral Rotating Cathode Arc, Thin Solid Films, 2009, 517, p 4845–4849. https://doi.org/10.1016/j.tsf.2009.03.038CrossRef

44.

J.H. Hsieh, A.L.K. Tan and X.T. Zeng, Oxidation and Wear Behaviors of Ti-Based Thin Films, Surf. Coat. Tech., 2006, 201, p 4094–4098. https://doi.org/10.1016/j.surfcoat.2006.08.026CrossRef

45.

V.F.C. Sousa, F.J.G. Da Silva, G.F. Pinto, A. Baptista and R. Alexandre, Characteristic and Wear Mechanisms of TiAlN-Based Coatings for Machining Applications: A Comprehensive Review, Metals, 2021, 11, p 260–309. https://doi.org/10.3390/met11020260CrossRef

46.

W. Grzesik, Z. Zalisz and S. Krol, Nieslony, Investigations on Friction and Wear Mechanisms of the PVD-TiAlN Coated Carbide in Dry Sliding Against Steel and Cast Iron, Wear, 2006, 261, p 1191–1200. https://doi.org/10.1016/j.wear.2006.03.004CrossRef

47.

V. Nunes, F.J.G. Silva, M.F. Andrade, R. Alexandre and A.P.M. Baptista, Increasing the Lifespan of High-Pressure Die Cast Molds Subjected to Severe Wear, Surf. Coat. Tech., 2017, 332, p 319–331. https://doi.org/10.1016/j.surfcoat.2017.05.098CrossRef

48.

M.R. Alhafian, J.B. Chemin, Y. Fleming, L. Bourgeois, M. Penoy, R. Useldinger, F. Soldera, F. Mücklich and P. Choquet, Comparison on the Structural Mechanical and Tribological Properties of TiAlN Coatings Deposited by HiPIMS and Cathodic Arc Evaporation, Surf. Coat. Tech., 2021, 423, p 127529–127541. https://doi.org/10.1016/j.surfcoat.2021.127529CrossRef

49.

J. Zhao, Z. Liu, X. Ren, B. Wang, Y. Cai, Q. Song and Y. Wan, Coatin-Thickness-Dependent Physical Properties and Cutting Temperature for Cutting Inconel 718 with TiAlN Coated tools, J. Adv. Res., 2021 https://doi.org/10.1016/j.jare.2021.07.009CrossRef

50.

M.H. Sulaiman, R.N. Farahana, K. Bienk, C.V. Nielsen and N. Bay, Effects of DLC/TiAlN-Coated Die on Friction and Wear in Sheet-Metal Forming under Dry and Oil-Lubricated Conditions: Experimental and Numerical Studies, Wear, 2019 https://doi.org/10.1016/j.wear.2019.203040CrossRef

51.

H.X. Zhang, H.J. Yu and C.Z. Chen, Microstructure and Wear Resistance of Composite Coating by Laser Cladding Al/TiN on the Ti–6Al–4V Substrate, Surf. Rev. Lett., 2015, 22, p 1550044–1550047. https://doi.org/10.1142/S0218625X15500444CrossRef

52.

G. Li, L. Zhang, F. Cai, Y. Yang, Q. Wang and S. Zhang, Characterization and Corrosion Behaviors of TiN/TiAlN Multilayer Coatings by Ion Source Enhanced Hybrid Arc Ion Plating, Surf. Coat. Technol., 2019, 366, p 355–365. https://doi.org/10.1016/j.surfcoat.2019.03.027CrossRef

53.

W. Liu, Q. Chu, J. Zeng, R. He, H. Wu and Z. Wu, PVD-CrAlN and TiAlN Coated Si3N4 Ceramic Cutting Tools-1, Microstruct. Turn. Perform. Wear Mech. Ceram. Int., 2017, 43(12), p 8999–9004. https://doi.org/10.1016/j.ceramint.2017.04.041CrossRef

54.

A.P. Kulkarni and V.G. Sargade, Characterization and Performance of AlTiN, AlTiCrN, TiN/TiAlN PVD Coated Carbide Tools While Turning SS 304, Mater. Manuf. Process., 2015, 30(6), p 748–755. https://doi.org/10.1080/10426914.2014.984217CrossRef

55.

K. Khlifi and A.B.C. Larbi, Mechanical Properties and Adhesion of TiN Monolayer and TiN/TiAlN Nanolayer Coatings, J. Adhes. Sci. Technol., 2013, 28(1), p 85–96. https://doi.org/10.1080/01694243.2013.827094CrossRef

56.

T. Sprute, W. Tillmann, D. Grisales, U. Selvadurai and G. Fischer, Influence of Substrate Pre-Treatments on Residual Stress and Tribo-Mechanical Properties of TiAlN-Based PVD Coatings, Surf. Coat. Technol., 2014, 260, p 369–379. https://doi.org/10.1016/j.surfcoat.2014.08.075CrossRef

57.

K.V. Chauhan and S.K. Rawal, A Review Paper on Tribological and Mechanical Properties of Ternary Nitride based Coatings, Proc. Technol., 2014, 14, p 430–437. https://doi.org/10.1016/j.protcy.2014.08.055CrossRef

58.

M. Ghufran, G.M. Uddin, S.M. Arafat, M. Jawad and A. Rehman, Development and Tribo-Mechanical Properties of Functional Ternary Nitride Coatings: Applications-Based Comprehensive Review, J. Eng. Tribol., 2020 https://doi.org/10.1177/1350650120933412CrossRef

59.

O. Comakli, Improved Structural, Mechanical, Corrosion and Tribocorrosion Properties of Ti45Nb Alloys by TiN, TiAlN Monolayers and TiAlN/TiN Multilayer Ceramic Films, Ceram. Int., 2021, 47, p 4149–4156. https://doi.org/10.1016/j.ceramint.2020.09.292CrossRef

60.

A.S. Kamenetskih, A.I. Kukharenko, E.Z. Kurmaev, N.A. Skorikov, N.V. Gavrilov, S.O. Cholakh, A.V. Chukin, V.M. Zainullina and M.A. Korotin, Characterization of TiAlSiON Coatings Deposited by Plasma Enhanced Magnetron Sputtering: XRD, XPS, and DFT Studies, Surf. Coat. Tech., 2015, 278, p 87–91. https://doi.org/10.1016/j.surfcoat.2015.08.007CrossRef

61.

J.M. Paiva, G. Fox-Rabinovich, E.L. Junior, P. Stolf, Y.S. Ahmed, M.M. Martins, C. Bork and S. Veldhuis, Tribological and Wear Performance of Nanocomposite PVD Hard Coatings Deposited on Aluminum Die Casting Tool, Materials, 2018, 11, p 358–415. https://doi.org/10.3390/ma11030358CrossRef

62.

I.A. Shulepov, E.B. KashKarov, I.B. Stepanov, M.S. Syratanov, A.N. Sutygina, A. Obrosov and S. Weis, The Formation of Composite Ti-Al-N Coatings using Filtered Vacuum Arc Deposition with Separate Cathodes, Metals, 2017, 7, p 497–509. https://doi.org/10.3390/met7110497CrossRef

63.

A.S. Hammood and H.M. Lieth, A Study the Effect of Retained Austenite on Fatigue Life of Austempering Ductile Iron by Using Artificial Neural Networks, Int. J. Curr. Eng. Technol., 2013, 3, p 1946–1951.

64.

H. Elmkhah, F. Mahboubi, A. Abdollah-zadeh and A.R. Sabour Rouhaghdam, A New Approach to Improve the Surface Properties Of H13 Steel for Metal Forming Applications by Applying the TiAlN Multi-Layer Coating, J. Manuf. Process., 2018, 32, p 873–877. https://doi.org/10.1016/j.jmapro.2018.04.010CrossRef

65.

Y.M. Durmaz and F. Yildiz, The Wear Performance of Carbide Tools Coated with TiAlSiN, AlCrN and TiAlN Ceramic Films in Intelligent Machining Process, Ceram. Int., 2018, 45, p 3839–3848. https://doi.org/10.1016/j.ceramint.2018.11.055CrossRef

66.

H. Caliskan, P. Panjan and S. Paskvale, Monitoring of Wear Characteristics of TiN and TiAlN Coatings at Long Sliding Distances, Tribol. Trans., 2014, 57, p 496–502. https://doi.org/10.1080/10402004.2014.884254CrossRef

67.

M. Kumar and A. Megalingam, Tribological Characterization of Al6061/Alumina/Graphite/ Redmud Hybrid Composite for Brake Rotor Application, Part. Sci. Technol., 2017, 37, p 261–274. https://doi.org/10.1080/02726351.2017.1367747CrossRef

68.

C.W. Cho and Y.Z. Lee, Effects of the Oxide Layer on the Friction Characteristics Between TiN Coated Ball and Steel Disk in Dry Sliding, Wear, 2003, 254, p 383–390. https://doi.org/10.1016/S0043-1648(03)00021-8CrossRef

69.

S.K. Singh, A. Pramanik, S. Kumar and A.K. Basak, Effect of Lubrication on the Wear Behavior of CrN Coating Deposited by PVD Process, Int. J. Surf. Sci. Eng., 2019, 13, p 60–78. https://doi.org/10.1504/IJSURFSE.2019.10019189CrossRef

70.

E. Vogli, W. Tillmann, U. Selvadurai-Lassl, G. Fischer and J. Herper, Influence of Ti/TiAlN-Multilayer Designs on their Residual Stresses and Mechanical Properties, Appl. Surf. Sci., 2011, 257, p 8550–8557. https://doi.org/10.1016/j.apsusc.2011.05.013CrossRef

71.

K.S. Selivanov, A.M. Smyslov, Y.M. Dyblenko and I.P. Semenova, Erosive Wear Behavior of Ti/Ti(V, Zr)N Multilayered PVD Coatings for Ti–6Al–4V Alloy, Wear, 2019, 418, p 160–166. https://doi.org/10.1016/j.wear.2018.11.016CrossRef

72.

F. Bouville, E. Maire, S. Meille, B. Van de Moortele, A.J. Stevenson and S. Deville, Strong, Tough and Stiff Bioinspired Ceramics from Brittle Constituents, Nat. Mater., 2014, 13, p 508–514. https://doi.org/10.1038/nmat3915CrossRef

73.

P. Wieciński, J. Smolik, H. Garbacz and K.J. Kurzydlowski, Microstructure and Mechanical Properties of Nanostructure Multilayer CrN/Cr Coatings on Titanium Alloy, Thin Solid Films, 2011, 519, p 4069–4073. https://doi.org/10.1016/j.tsf.2011.01.183CrossRef

74.

J. Shuai, X. Zuo, Z. Wang, P. Guo, B. Xu, J. Zhou, A. Wang and P. Ke, Comparative Study on Crack Resistance of TiAlN Monolithic and Ti/TiAlN Multilayer Coatings, Ceram. Int., 2020, 46, p 6672–6681. https://doi.org/10.1016/j.ceramint.2019.11.155CrossRef

Title: Investigation into Coating Structure and Wear Environment Effects on Tribological Properties of Piston Ring Coated with Monolayer TiAlN and Multilayer TiN/TiAlN
Authors: Sevim Hamamci Alisir
Dileknur Evrensel
Publication date: 08-10-2021
Publisher: Springer US
Published in: Journal of Materials Engineering and Performance / Issue 2/2022
Print ISSN: 1059-9495
Electronic ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-021-06288-w

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 2/2022

Experimental and Numerical Study on Ductile Fracture Prediction of Aluminum Alloy 6016-T6 Sheets Using a Phenomenological Model

Molecular Dynamics Simulation of the Tensile Deformation Behavior of the γ(TiAl)/α2(Ti3Al) Interface at Different Temperatures

Hot Deformation Behavior and Processing Map of Cu-Cr-Nb-Zr Alloy

Structural Elucidation with Improved Dielectric and Magnetic Properties of Sol–Gel Synthesized Cr3+ Substituted M-Type Sr2+ Hexaferrites

Microstructure and Wear Properties of Electrodeposited Ni-B-Al2O3 Composite Coating on Low Carbon Steel at Elevated Temperature

Influence of Fused Deposition Molding Printing Process on the Toughness and Miscibility of Polylactic Acid/Polycaprolactone Blends

Premium Partners