Top

Journal of Intelligent Manufacturing

Published in:

23-04-2014

Micro-milling performance of AISI 304 stainless steel using Taguchi method and fuzzy logic modelling

Authors: Emel Kuram, Babur Ozcelik

Published in: Journal of Intelligent Manufacturing | Issue 4/2016

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

In this study, micro-milling of AISI 304 stainless steel with ball nose end mill was conducted using Taguchi method. The influences of spindle speed, feed rate and depth of cut on tool wear, cutting forces and surface roughness were examined. Taguchi’s signal to noise ratio was utilized to optimize the output responses. The influence of control parameters on output responses was determined by analysis of variance. In this study, the models describing the relationship between the independent variables and the dependent variables were also established by using regression and fuzzy logic. Efficiency of both models was determined by analyzing correlation coefficients and by comparing with experimental values. The results showed that both regression and fuzzy logic modelling could be efficiently utilized for the prediction of tool wear, cutting forces and surface roughness in micro-milling of AISI 304 stainless steel.

previous article Risk evaluation in failure mode and effects analysis using fuzzy digraph and matrix approach

next article An improved teaching-learning-based optimization algorithm for numerical and engineering optimization problems

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

Biermann, D., Kahleyss, F., & Surmann, T. (2009). Micromilling of NiTi shape-memory alloys with ball nose cutters. Materials and Manufacturing Processes, 24, 1266–1273.CrossRef

Bissacco, G., Hansen, H. N., & De Chiffre, L. (2006). Size effects on surface generation in micro milling hardened tool steel. CIRP Annals - Manufacturing Technology, 55, 593–596.CrossRef

Caliskan, H., Kurbanoglu, C., Panjan, P., & Kramar, D. (2013). Investigation of the performance of carbide cutting tools with hard coatings in hard milling based on the response surface methodology. The International Journal of Advanced Manufacturing Technology, 66, 883–893.CrossRef

Cardoso, P., & Davim, J. P. (2010). Optimization of surface roughness in micromilling. Materials and Manufacturing Processes, 25, 1115–1119.CrossRef

Gokulachandran, J., & Mohandas, K. (2013). Comparative study of two soft computing techniques for the prediction of remaining useful life of cutting tools. Journal of Intelligent Manufacturing,. doi:10.1007/s10845-013-0778-2.

Hanafi, I., Khamlichi, A., Cabrera, F. M., López, P. J. N., & Jabbouri, A. (2012). Fuzzy rule based predictive model for cutting force in turning of reinforced PEEK composite. Measurement, 45, 1424–1435.CrossRef

Huang, P. B. (2014). An intelligent neural-fuzzy model for an in-process surface roughness monitoring system in end milling operations. Journal of Intelligent Manufacturing,. doi:10.1007/s10845-014-0907-6.

Huang, W., & Kovacevic, R. (2011). A neural network and multiple regression method for the characterization of the depth of weld penetration in laser welding based on acoustic signatures. Journal of Intelligent Manufacturing, 22, 131–143.CrossRef

Huo, D., & Cheng, K. (2010). Experimental investigation on micromilling of oxygen-free, high-conductivity copper using tungsten carbide, chemistry vapour deposition, and single-crystal diamond micro tools. Proceedings of the Institution of Mechanical Engineerings, Part B: Journal of Engineering Manufacture, 224, 995–1003.CrossRef

Iqbal, A., Zhang, H.-C., Kong, L. L., & Hussain, G. (2013). A rule-based system for trade-off among energy consumption, tool life, and productivity in machining process. Journal of Intelligent Manufacturing,. doi:10.1007/s10845-013-0851-x.

Kang, I.-S., Kim, J.-S., & Seo, Y.-W. (2011). Investigation of cutting force behaviour considering the effect of cutting edge radius in the micro-scale milling of AISI 1045 steel. Proceedings of the Institution of Mechanical Engineerings, Part B: Journal of Engineering Manufacture, 225, 163–171.

Kovac, P., Rodic, D., Pucovsky, V., Savkovic, B., & Gostimirovic, M. (2013). Application of fuzzy logic and regression analysis for modeling surface roughness in face milling. Journal of Intelligent Manufacturing, 24, 755–762.CrossRef

Kuram, E., & Ozcelik, B. (2013a). Multi-objective optimization using Taguchi based grey relational analysis for micro-milling of Al 7075 material with ball nose end mill. Measurement, 46, 1849–1864.CrossRef

Kuram, E., & Ozcelik, B. (2013b). Fuzzy logic and regression modelling of cutting parameters in drilling using vegetable based cutting fluids. Indian Journal of Engineering & Materials Sciences, 20, 51–58.

Lai, X., Li, H., Li, C., Lin, Z., & Ni, J. (2008). Modelling and analysis of micro scale milling considering size effect, micro cutter edge radius and minimum chip thickness. International Journal of Machine Tools & Manufacture, 48, 1–14.CrossRef

Latha, B., & Senthilkumar, V. S. (2009). Analysis of thrust force in drilling glass fiber-reinforced plastic composites using fuzzy logic. Materials and Manufacturing Processes, 24, 509–516.CrossRef

Latha, B., & Senthilkumar, V. S. (2010). Modeling and analysis of surface roughness parameters in drilling GFRP composites using fuzzy logic. Materials and Manufacturing Processes, 25, 817–827.CrossRef

Li, S., Liu, Y., Li, Y., Landers, R. G., & Tang, L. (2013a). Process planning optimization for parallel drilling of blind holes using a two phase genetic algorithm. Journal of Intelligent Manufacturing, 24, 791–804.CrossRef

Li, S., Liu, F., Chen, B., & Li, C. B. (2013b). Multi-objective optimization of cutting parameters in sculptured parts machining based on neural network. Journal of Intelligent Manufacturing. doi:10.1007/s10845-013-0809-z.

Mian, A. J., Driver, N., & Mativenga, P. T. (2011). Identification of factors that dominate size effect in micro-machining. International Journal of Machine Tools & Manufacture, 51, 383–394.

Natarajan, U., Periyanan, P. R., & Yang, S. H. (2011). Multiple-response optimization for micro-endmilling process using response surface methodology. The International Journal of Advanced Manufacturing Technology, 56, 177–185.

Pandey, R. K., & Panda, S. S. (2013). Optimization of bone drilling using Taguchi methodology coupled with fuzzy based desirability function approach. Journal of Intelligent Manufacturing,. doi:10.1007/s10845-013-0844-9.

Park, J.-B., Wie, K.-H., Park, J.-S., & Ahn, S.-H. (2009). Evaluation of machinability in the micro end milling of printed circuit boards. Proceedings of the Institution of Mechanical Engineerings, Part B: Journal of Engineering Manufacture, 223, 1465–1474.CrossRef

Quintana, G., Garcia-Romeu, M. L., & Ciurana, J. (2011). Surface roughness monitoring application based on artificial neural networks for ball-end milling operations. Journal of Intelligent Manufacturing, 22, 607–617.CrossRef

Radhakrishnan, T., & Nandan, U. (2005). Milling force prediction using regression and neural networks. Journal of Intelligent Manufacturing, 16, 93–102.CrossRef

Ramesh, S., Karunamoorthy, L., & Palanikumar, K. (2008). Fuzzy modeling and analysis of machining parameters in machining titanium alloy. Materials and Manufacturing Processes, 23, 439–447.CrossRef

Sibalija, T. V., & Majstorovic, V. D. (2012). An integrated approach to optimise parameter design of multi-response processes based on Taguchi method and artificial intelligence. Journal of Intelligent Manufacturing, 23, 1511–1528.CrossRef

Singh, A., Datta, S., Mahapatra, S. S., Singha, T., & Majumdar, G. (2013). Optimization of bead geometry of submerged arc weld using fuzzy based desirability function approach. Journal of Intelligent Manufacturing, 24, 35–44.CrossRef

Sreeram, S., & Senthil Kumar, A. (2006). Optimization of cutting parameters in micro end milling operations under dry cutting conditions using genetic algorithms. The International Journal of Advanced Manufacturing Technology, 30, 1030–1039.CrossRef

Uhlmann, E., Piltz, S., & Schauer, K. (2005). Micro milling of sintered tungsten-copper composite materials. Journal of Materials Processing Technology, 167, 402–407.CrossRef

Vázquez, E., Rodríguez, C., Elías-Zúñiga, A., & Ciurana, J. (2010). An experimental analysis of process parameters to manufacture metallic micro-channels by micro-milling. The International Journal of Advanced Manufacturing Technology, 51, 945–955.CrossRef

Zadeh, L. A. (1975). The concept of a linguistic variable and its application to approximate reasoning-I. Information Sciences, 8, 199–249.CrossRef

Zhao, D., Wang, Y., Seng, S., & Lin, Z. (2013). Multi-objective optimal design of small scale resistance spot welding process with principal component analysis and response surface methodology. Journal of Intelligent Manufacturing,. doi:10.1007/s10845-013-0733-2.

Title: Micro-milling performance of AISI 304 stainless steel using Taguchi method and fuzzy logic modelling
Authors: Emel Kuram
Babur Ozcelik
Publication date: 23-04-2014
Publisher: Springer US
Published in: Journal of Intelligent Manufacturing / Issue 4/2016
Print ISSN: 0956-5515
Electronic ISSN: 1572-8145
DOI: https://doi.org/10.1007/s10845-014-0916-5

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 4/2016

An intelligent approach to supplier evaluation in automotive sector

A multi-objective TLBO algorithm for balancing two-sided assembly line with multiple constraints

The knowledge modeling system of ready-mixed concrete enterprise and artificial intelligence with ANN-GA for manufacturing production

Risk evaluation in failure mode and effects analysis using fuzzy digraph and matrix approach

A generalized-exponential decomposition method for the analysis of inhomogeneous assembly/disassembly systems with unreliable machines and finite buffers

Continuous prediction of manufacturing performance throughout the production lifecycle

Premium Partners