Top

Polymer Science, Series D

Published in:

01-06-2022

Recovering a Reducing-Gear Shaft Neck by Reinforced-Bush Adhesion

Authors: A. S. Kononenko, I. Yu. Ignatkin, A. V. Drozdov

Published in: Polymer Science, Series D | Issue 2/2022

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

A sophisticated approach to the recovery of the worn shaft neck of a general-purpose reducing gear operating in contact with a rubber–metal seal by means of adhesion of a reinforced repair bush was considered. Alternative methods for repair were analyzed, the optimal mode of reinforcing chemical–thermal treatment of repair details was determined, and their relative wear resistance was tested. Results of experimental studies on the evaluation of the effect of nitriding on the strength of adhesive joint are given.

previous article A Composition Based on a Siloxane Block Copolymer with a Linear-Ladder Structure Intended for Use in Electronic Instrumentation

next article Thermally Stable Polyimide Structural Adhesives

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

O. M. Mel’nikov, “Performance of shaft-cuff joints and increase of their reliability,” Vestn. Mosk. Gos. Agroinzh. Univ. im. V.P. Goryachkina, No. 2 (84), 346–349 (2018).

V. I. Chernoivanov and I. G. Golubev, Reparation of Machine Parts: Status and Prospects (Rosinformagrotekh, Moscow, 2010) [in Russian].

N. F. Struchkov, “The influence of technological parameters of electric arc metallization on the microstructure and microhardness of coatings,” Tr. Gos. Nauchno-Issled. Tekhnol. Inst. Remonta Ekspl. Trakt. S-kh. Mash. 118, 173–175 (2015).

N. N. Chupyatov, Doctoral Dissertation in Engineering (Russian State Agrarian Univ.–Moscow Timiryazev Agricultural Acad., Moscow, 2018).

A. E. Smirnov and M. Yu. Semenov, “Application of vacuum thermal and chemical-thermal treatment for hardening of heavily loaded parts of machines, devices, and tools,” Nauka Obraz., No. 2 (2014). https://doi.org/10.7463/0214.0700036

W. Grafen and B. Edenhofer, “Acetylene low-pressure carburising—a novel and superior carburizing technology,” Heat Treat. Met. 26 (4), 79–85 (1999).

Yu. M. Lakhtin, Ya. D. Kogan, G. I. Shpis, and Z. Bemer, Theory and Technology of Nitriding (Metallurgiya, Moscow, 1991) [in Russian].

A. S. Kononenko and I. A. Kuznetsov, “Restoration of seats for rolling bearings in machine body parts with polymer nanocomposites,” Tr. Gos. Nauchno-Issled. Tekhnol. Inst. Remonta Ekspl. Trakt. S-kh. Mash. 124 (2), 81–85 (2016).

A. S. Kononenko, A. A. Solovyeva, and V. F. Komogortsev, “Theoretical determination of the minimum thickness of a polymer layer providing ensured protection of a shaft-bearing joint from fretting corrosion,” Polym. Sci., Ser. D 13, 45–49 (2020).

10.

J. Michalski and E. Wołowiec-Korecka, “A study of parameters of nitriding processes. Part 1,” Met. Sci. Heat Treat. 61, 183–190 (2019).CrossRef

11.

J. Michalski and E. Wołowiec-Korecka, “A study of the parameters of nitriding processes. Part 2,” Met. Sci. Heat Treat. 61, 351–359 (2019).CrossRef

12.

A. S. Kononenko and A. A. Solov’eva, RF Patent No. 180309 (2018).

13.

O. M. Mel’nikov, S. P. Kazantsev, O. V. Chekha, “Assessment of the quality of parts and shaft-cuff joints,” Vestn. Mosk. Gos. Agroinzh. Univ. im. V.P. Goryachkina, No. 5 (93), 8–13 (2019).

14.

A. A. Asheichik and V. L. Polonskii, “Experimental study of the properties of sealing rubbers at high and low temperatures,” Vestn. Sib. Os. Aerokosm. Univ. 17 (3), 656–664 (2016).

Title: Recovering a Reducing-Gear Shaft Neck by Reinforced-Bush Adhesion
Authors: A. S. Kononenko
I. Yu. Ignatkin
A. V. Drozdov
Publication date: 01-06-2022
Publisher: Pleiades Publishing
Published in: Polymer Science, Series D / Issue 2/2022
Print ISSN: 1995-4212
Electronic ISSN: 1995-4220
DOI: https://doi.org/10.1134/S1995421222020113

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 2/2022

Properties of an Epoxy Blends Modified with a Thermoplastic Heat-Resistant Polymer and an Active Diluent for Manufacture of Reinforced Plastics

The Effect of Reinforcing Fillers of Different Types on Properties of VK-51 Adhesive

Studying the Properties of Composites with a Polyvinylchloride Matrix and Meadow-Grass-Hay Filler

The Effect of Fillers on Thermal-Conductivity Materials Based on Silicon–Organic Oligomers (Review)

The Effect of Multiple Curing on the Characteristics of an Epoxy Matrix and Its Adhesion to Fibers

Thermogravimetric Analysis of a Weld-Bonded Joint with Various Types of Adhesive Materials

Premium Partners