Top

Journal of Materials Engineering and Performance

Published in:

29-09-2021

Tribological Properties and Friction-Induced Noise Performance of M50 with Curved Microchannels Filled by Sn-Ag-Cu and Ti₃C₂

Authors: Feng Peng, Xiaoliang Shi, Yawen Xue, Qipeng Huang, Chaohua Wu

Published in: Journal of Materials Engineering and Performance | Issue 2/2022

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

M50 steel is one of the most widely used high-performance bearing steels, and the tribological properties are related to its service life. In this paper, the dry sliding tribological tests of M50, M50-Sn-Ag-Cu and M50-Sn-Ag-Cu-Ti₃C₂ against Si₃N₄ ceramic balls under different loads were carried out. Through the analysis of worn surface and cross section of wear scar, as well as characteristics of friction signal, the causes of frictional noise are discussed, and the influence of Ti₃C₂ on the frictional noise is revealed. The results show that the addition of Ti₃C₂ can significantly improve the tribological performance of M50-Sn-Ag-Cu-Ti₃C₂, reduce the intensity of frictional noise and suppress its high-frequency components. Frictional noise is caused by the system energy dissipation due to the contact surface roughness. The synergistic effect of Ti₃C₂ and Sn-Ag-Cu makes the lubricant be easily extruded to the contact surface, which will form a protective layer on the worn surface, thus reducing the surface roughness and frictional noise and improving the tribological performance.

previous article Comparative Study on Tribological Behaviors of Two TiZr-Based Alloys in Vacuum

next article Effect of Susceptors on Joining of AA6061-T6 to AZ31B by Microwave Hybrid Heating

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

P. Mukhopadhyay, P. Kannaki, M. Srinivas and M. Roy, Microstructural Developments During Abrasion of M50 Bearing Steel, Wear, 2014, 315(1–2), p 31–37.CrossRef

J. Nygaard, M. Rawson, P. Danson and H. Bhadeshia, Bearing Steel Microstructures After Aircraft Gas Turbine Engine Service, J. Mater. Sci. Technol., 2014, 30(15), p 1911–1918.CrossRef

J.Y. Xu, J.L. Mo, B. Huang, X.C. Wang, X. Zhang and Z.R. Zhou, Reducing Friction-Induced Vibration and Noise by Clearing Wear Debris From Contact Surface by Blowing Air and Adding Magnetic Field, Wear, 2018, 408, p 238–247.CrossRef

H.Y. Zhou, X.L. Shi, Z.Y. Yang, C.H. Wu, G.C. Lu and Y.W. Xue, Tribological Property and Frictional Noise Performance of Titanium Alloys with Sn-Ag-Cu and TiC Filled into Surface Dimples, Tribol. Int., 2020, 144, p 106121.CrossRef

D.W. Wang, J.L. Mo, Z.Y. Zhu, H. Ouyang, M.H. Zhu and Z.R. Zhou, How do grooves on friction interface affect tribological and vibration and squeal noise performance, Tribol. Int., 2017, 109, p 192–205.CrossRef

A.Y. Wang, J.L. Mo, X.C. Wang, M.H. Zhu and Z.R. Zhou, Effect of Surface Roughness on Friction-Induced Noise: Exploring the Generation of Squeal at Sliding Friction Interface, Wear, 2018, 402, p 80–90.CrossRef

H.Y. Zhou, X.L. Shi, A.M.M. Ibrahim, X.Y. Liu, G.C. Lu and Y. Chen, Tribological and Friction-Induced Vibration and Noise Performance of Ti₆Al₄V-Multilayer Graphene Self-Lubricating Composites, Mater. Res. Express., 2018, 5(9), p 096511.CrossRef

D.W. Wang, J.L. Mo, M.Q. Liu, H. Ouyang and Z.R. Zhou, Noise Performance Improvements and Tribological Consequences of a Padon-Disc System Through Groove-Textured Disc Surface, Tribol. Int., 2016, 102, p 222–236.CrossRef

J.L. Mo, Z.G. Wang, G.X. Chen, T.M. Shao, M.H. Zhu and Z.R. Zhou, The effect of groove-textured surface on friction and wear and friction-induced vibration and noise, Wear, 2013, 301, p 671–811.CrossRef

10.

R.A.L. Rorrer and V. Juneja, Friction-Induced Vibration and Noise Generation of Instrument Panel Material Pairs, Tribol. Int., 2002, 35(8), p 523–531.CrossRef

11.

J. Nam, J. Baek, H. Do and J. Kang, Experimental Investigation of Friction Noise on Lubricated Contact, J. Mech. Sci. Technol., 2017, 31(12), p 5751–5760.CrossRef

12.

J.B. Zhao, Y. Wang, B. Han, M.Y. Li and G. Cui, Antifriction Effects of Cu₂S Film on Ni-Based MMC Coating, Surf. Coat. Tech., 2017, 315, p 391–398.CrossRef

13.

J.G. Fu, C.Q. Xu, D.Q. Ma, X.H. Zhu, D. Cheng, Z.J. Yan, C.S. Ma, G.S. Liu and Y.Y. Fu, Tribological Properties and Releasing Behavior of Solid Lubricant WS₂ in the Dimples on Cylinder Liner Surface of Diesel Engine, Tribol. Int., 2021, 158, p 106936.CrossRef

14.

J. Zhang, G.C. Lu, X.L. Shi, Z.Y. Yang, Y.W. Xue and H.Z. Zhou, Improving Tribological Performance of Inconel 625 by Combining Groove-Textured Surfaces with Sn-Ag-Cu Solid Lubricant, J. Mater. Eng. Perform., 2021, 30(1), p 154–164.CrossRef

15.

A. Rosenkranz, H.L. Costa, M.Z. Baykara and A. Martini, Synergetic Effects of Surface Texturing and Solid Lubricants to Tailor Friction and Wear – A Review, Tribol. Int., 2021, 155, p 106792.CrossRef

16.

X.Y. Liu, X.L. Shi, Y.H. Huang, X.B. Deng, Z. Yan and B. Xue, Anti-Friction and Wear Properties of the Friction Surface of M50–10 wt% (50Sn40Ag10Cu) Composite, J. Alloys Compd., 2018, 765, p 7–17.CrossRef

17.

F.A. Essa, Q.X. Zhang and X.J. Huang, Improved Friction and Wear of M50 Steel Composites Incorporated With ZnO as a Solid Lubricant With Different Concentrations Under Different Loads, J. Mater. Eng. Perform., 2017, 4, p 1–12.

18.

M. Marian, G.C. Song, B. Wang, V.M. Fuenzalida, S. Krauss, B. Merle, S. Tremmel, S. Wartzack, J.H. Yu and A. Rosenkranz, Effective Usage of 2D MXene Nanosheets as Solid Lubricant – Influence of Contact Pressure and Relative Humidity, Appl. Surf. Sci., 2020, 531, p 147311.CrossRef

19.

Y.J. Mai, Y.G. Li, S.L. Li, L.Y. Zhang, C.S. Liu and X.H. Jie, Self-Lubricating Ti₃C₂ Nanosheets/Copper Composite Coatings, J. Alloys. Compd., 2019, 770, p 1–5.CrossRef

20.

H. Zhang, L. Wang, Q. Chen, P. Li, A. Zhou, X. Cao and Q. Hu, Preparation, mechanical and anti-friction performance of MXene/polymer composites, Mater. Des., 2016, 92, p 682–689.CrossRef

21.

D. Zhang, M. Ashton, A. Ostadhossein, A.C. van Duin, R.G. Hennig and S.B. Sinnott, Computational Study of Low Interlayer Friction in Ti_n+1C_n (n=1, 2, and 3) MXene, ACS. Appl. Mater. Interfaces., 2017, 9, p 34467–34479.CrossRef

22.

J. Tian, R. Jiang, P. Gao, D. Xu, L. Mao, G. Zeng, M. Liu, F. Deng, X. Zhang and Y. Wei, Synthesis and Cell Imaging Applications of Amphiphilic AIE-Active Poly (Amino Acid) s, Mater. Sci. Eng. C-Mater., 2017, 79, p 563–569.CrossRef

23.

Y. Liu, X.F. Zhang, S.L. Dong, Z.Y. Ye and Y.D. Wei, Synthesis and Tribological Property of Ti₃C₂T_X Nanosheets, J. Mater. Sci., 2017, 52(4), p 2200–2209.CrossRef

24.

X.H. Zhang, M.Q. Xue, X.H. Yang, Z.P. Wang, G.S. Luo, Z.D. Huang, X.L. Sui and C.S. Li, Preparation and Tribological Properties of Ti₃C₂(OH)₂ Nanosheets as Additives in Base Oil, RSC. Adv., 2015, 5(4), p 2762–2767.CrossRef

25.

American Society for Testing and Materials, Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus. ASTM G99-95, 1995.

26.

H.B. Abdelounis, A.L. Bot, J. Perret-Liaudet and H. Zahouanim, An Experimental Study on Roughness Noise of Dry Rough Flat Surfaces, Wear, 2010, 268, p 335–345.CrossRef

27.

Y. Chen, X.L. Shi, G.C. Lu, H.Y. Zhou and Z.Y. Yang, Reducing Friction Noise of M50 Matrix Composites by Adding Ti₃SiC₂, Mater. Res. Express., 2019, 6(7), p 076510.CrossRef

28.

W.Q. Lian, Y.J. Mai, C.S. Liu, L.Y. Zhang, S.L. Li and X.H. Jie, Two-Dimensional Ti₃C₂ Coating as an Emerging Protective Solid-Lubricant for Tribology, Ceram. Int., 2018, 44(16), p 20154–20162.CrossRef

Title: Tribological Properties and Friction-Induced Noise Performance of M50 with Curved Microchannels Filled by Sn-Ag-Cu and Ti3C2
Authors: Feng Peng
Xiaoliang Shi
Yawen Xue
Qipeng Huang
Chaohua Wu
Publication date: 29-09-2021
Publisher: Springer US
Published in: Journal of Materials Engineering and Performance / Issue 2/2022
Print ISSN: 1059-9495
Electronic ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-021-06286-y

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 2/2022

Correlation Between Processing Parameters in Direct Metal Deposition of IN625 Nickel-Base Superalloy

Preparation of Antibacterial and Strengthened High-Density Polyethylene Composites via Compounding with Silver Ion Glass Microbead-Loaded Basalt Fiber

Effect of Solution Heat Treatment on the Microstructure and Hardness of theTi-48Al-2Cr-2Nb Alloy Prepared by Electron Beam Smelting

Influence of Interlayer Nb on the Performance of Joint Between Titanium and Steel Welded by Resistance Spot Welding

Tensile Fracture Behavior of Cu/Al Butt Friction Stir Welding: Role of Interface Morphology

Mechanical Properties and Microstructure Transformation Behavior for Welded Joints in Ship Plate Steel with High-Heat Input Welding

Premium Partners