Top

Journal of Materials Engineering and Performance

Published in:

18-10-2021

Corrosion Properties of Heterostructured [8YSZ/Al₂O₃]N Coatings as a Function of the Bilayer Number

Authors: C. H. Ortiz, J. C. Caicedo, W. Aperador

Published in: Journal of Materials Engineering and Performance | Issue 2/2022

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

This study presents a detailed analysis of the wear presented in [8YSZ/α-Al₂O₃] multilayer coatings as a function of the bilayer number when exposed to a corro-erosive environment. In this study, the roughness and grain size decreased by 58 and 30%, respectively when comparing the 70 bilayers system with the 1 bilayer system. The surface factors and the higher bilayer number of the n = 70 system, influenced the 67.33% decrease in corrosion rate compared to the 1 bilayer system. Subsequently, by means of SEM and optical microscopy, the degradation of the coatings due to the impact of abrasive particles and the generation of oxides on the substrate surface caused by a partial delamination of the coating was evidenced. This wear was calculated by means of the mass loss after the corro-erosive test, obtaining a decrease of 55.25% for the system with 70 bilayers with respect to the system with 1 bilayer. The results obtained showed that the system with 70 bilayers presented the best set of electrochemical properties and lower wear in corrosive environments, which makes it the best candidate to be used as a protective coating.

previous article Influence of Electrolyte Compositions and Electrical Parameters on Thermal Properties of Micro-Arc Oxidized AZ91 Alloy

next article Microstructure and Wear Properties of Electrodeposited Ni-B-Al2O3 Composite Coating on Low Carbon Steel at Elevated Temperature

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

A. Feuerstein, J. Knapp, T. Taylor, A. Ashary, A. Bolcavage and N. Hitchman, Technical and Economical Aspects of Current Thermal Barrier Coating Systems for Gas Turbine Engines By Thermal Spray and EBPVD: A Review, J. Therm. Spray Technol., 2008, 17(2), p 199–213. https://doi.org/10.1007/s11666-007-9148-yCrossRef

A. Escarraga, A. Toro, Y. Aguilar, J.C. Caicedo and G. Zambrano, Thermal Cyclic Response of [8YSZ/Al2O3]_n Multilayered Coatings Deposited Onto AISI 304 Stainless Steel, Mater. Chem. Phys., 2018, 216, p 526–533. https://doi.org/10.1016/j.matchemphys.2018.05.039CrossRef

A.G. González, F.M. Hurtado, H. Ageorges, E. López and F. Vargas, Evaluación del Comportamiento a la Corrosión en Sales Fundidas de Recubrimientos de Circona Estabilizada con Itria Elaborados por Proyección Termica por Plasma Atmosférico, Rev. Latinoam. Metal. y Mater., 2017, 37(1), p 2–10.

V. Kumar and K. Balasubramanian, Progress Update on Failure Mechanisms of Advanced Thermal Barrier Coatings: A Review, Prog. Org. Coatings, 2016, 90, p 54–82. https://doi.org/10.1016/j.porgcoat.2015.09.019CrossRef

G. Moskal, The Porosity Assessment of Thermal Barrier Coatings Obtained by APS Method, J. Achiev. Mater. Manuf. Eng. JAMME, 2007, 20(1–2), p 483–486. https://doi.org/10.1007/s00394-015-0886-1CrossRef

B. Saruhan, U. Schulz and M. Bartsch, Developments in Processing of Ceramic Top Coats of EB-PVD Thermal Barrier Coatings, Key Eng. Mater., 2007, 333, p 137–146. https://doi.org/10.4028/0-87849-424-3.137CrossRef

F. Blas et al., Processing Thermal Barrier Coatings Via Sol–Gel Route: Crack Network Control and Durability, Surf. Coatings Technol., 2017 https://doi.org/10.1016/j.surfcoat.2017.11.008CrossRef

D.G. Cahill et al., Nanoscale Thermal Transport, J. Appl. Phys., 2003, 93(2), p 793–818. https://doi.org/10.1063/1.1524305CrossRef

C.H. Ortiz, H.D. Colorado, W. Aperador and A. Jurado, Influence of the Number of Bilayers on the Mechanical and Tribological Properties in [TiN/TiCrN]_n Multilayer Coatings Deposited by Magnetron Sputtering, Tribol. Ind., 2019, 41(3), p 330–343. https://doi.org/10.24874/ti.2019.41.03.03CrossRef

10.

C. Zhu, A. Javed, P. Li, F. Yang, G.Y. Liang and P. Xiao, A Study of the Microstructure and Oxidation Behavior of Alumina/Yttria-Stabilized Zirconia (Al₂O₃/YSZ) Thermal Barrier Coatings, Surf. Coatings Technol., 2012, 212, p 214–222. https://doi.org/10.1016/j.surfcoat.2012.09.052CrossRef

11.

G. Venkadesan and J. Muthusamy, Experimental Investigation of Al2O3/8YSZ and CeO₂/8YSZ Plasma Sprayed Thermal Barrier Coating on Diesel Engine, Ceram. Int., 2019, 45(3), p 3166–3176. https://doi.org/10.1016/j.ceramint.2018.10.218CrossRef

12.

C. Amaya et al., Corrosion Study of Alumina/Yttria-Stabilized Zirconia (Al₂O₃/YSZ) Nanostructured Thermal Barrier Coatings (TBC) Exposed to High Temperature Treatment, Corros. Sci., 2009, 51, p 2994. CrossRef

13.

K. He, J.J. Chen, W.X. Weng, C.C. Li and Q. Li, Microstructure and Mechanical Properties of Plasma Sprayed Al₂O₃–YSZ Composite Coatings, Vacuum, 2018, 151, p 209–220. https://doi.org/10.1016/j.vacuum.2018.01.038CrossRef

14.

M.J. Kelly, D.E. Wolfe, J. Singh, J. Eldridge, D.M. Zhu and R. Miller, Thermal Barrier Coatings Design with Increased Reflectivity and Lower Thermal Conductivity for High-Temperature Turbine Applications, Int. J. Appl. Ceram. Technol., 2006, 3(2), p 81–93. https://doi.org/10.1111/j.1744-7402.2006.02073.xCrossRef

15.

C. Amaya et al., Influence of Bias Voltage on the Crystallographic Orientation and Morphology of Sputter Deposited Yttria Stabilized Zirconia (YSZ) Thin Films, Phys. status solidi, 2007, 4, p 4288–4293. https://doi.org/10.1002/pssc.200675925CrossRef

16.

G. De Películas, D. Universidad, Estudio del Comportamiento Tribológico y Adhesivo de Multicapas de [Al₂O₃/YSZ] 2006, 1(1), p 1–6

17.

L. Ipaz, J.C. Caicedo, J. Esteve, F.J. Espinoza-Beltran and G. Zambrano, Improvement of Mechanical and Tribological Properties in Steel Surfaces by Using Titanium–Aluminum/Titanium–Aluminum Nitride Multilayered System, Appl. Surf. Sci., 2012, 258(8), p 3805–3814. https://doi.org/10.1016/j.apsusc.2011.12.033CrossRef

18.

I.A. Mahmood, W.W. Jameel and L.A. Khaleel, Improved Oxidation Resistance for Thermal Barrier Ceramic Coating Protect, Int. J. Res. Eng. Technol. (IMPACT IJRET), 2013, 1(5), p 77–86.

19.

S. Vepřek and S. Reiprich, A Concept for the Design of Novel Superhard Coatings, Thin Solid Films, 1995, 268(1–2), p 64–71. https://doi.org/10.1016/0040-6090(95)06695-0CrossRef

20.

B. Podgornik, S. Hogmark, O. Sandberg and V. Leskovsek, Wear Resistance and Anti-sticking Properties of Duplextreated Forming Tool Steel, Wear, 2003, 254(11), p 1113–1121. https://doi.org/10.1016/S0043-1648(03)00322-3CrossRef

21.

K. Holmberg, H. Ronkainen and A. Matthews, Tribology of Thin Coatings, Ceram. Int., 2000, 26(7), p 787–795. https://doi.org/10.1016/S0272-8842(00)00015-8CrossRef

22.

W. Aperador, Estudio de la Resistencia a la Corrosión Electroquímica de Electro-recubrimientos Níquel/Cobre Obtenidos por Corriente Pulsante, Ing. y Desarollo, 2010, 27, p 48–61.

23.

A. Vargas, W. Aperador, C. Ortiz, J. Betancur and C. Wang, Caracterización Electroquímica de Fermanal Expuesto a Condiciones Corrosivas–Erosivas, Rev. Latinoam. Metalurg. Mater., 2009, 1(S1), p 149–155.

24.

P.E. Hovsepian et al., TiAlN/VN Superlattice Structured PVD Coatings: A New Alternative in Machining of Aluminium Alloys for Aerospace and Automotive Components, Surf. Coat. Technol., 2006, 201(1–2), p 265–272. https://doi.org/10.1016/J.SURFCOAT.2005.11.106CrossRef

25.

W. Aperador, J.C. Caicedo, C. España, G. Cabrera and C. Amaya, Bilayer Period Effect on Corrosion–Erosion Resistance for [TiN/AlTiN]_n Multilayered Growth on AISI 1045 Steel, J. Phys. Chem. Solids, 2010, 71(12), p 1754–1759. https://doi.org/10.1016/J.JPCS.2010.08.019CrossRef

26.

V. Bonu, M. Jeevitha, V. Praveen Kumar and G. Srinivas, Solid Particle Erosion and Corrosion Resistance Performance of Nanolayered Multilayered Ti/TiN and TiAl/TiAlN Coatings Deposited on Ti6Al4V Substrates, Surf. Coat. Technol., 2020, 387, p 125531. https://doi.org/10.1016/j.surfcoat.2020.125531CrossRef

27.

J.C. Caicedo, G. Cabrera, H.H. Caicedo, C. Amaya and W. Aperador, Nature in Corrosion–Erosion Surface for [TiN/TiAlN]_n Nanometric Multilayers Growth on AISI 1045 Steel, Thin Solid Films, 2012, 520(13), p 4350–4361. https://doi.org/10.1016/j.tsf.2012.02.061CrossRef

28.

W.A. Chaparro, C.R. Martin and E.V. López, Synergy Between Erosion–Corrosion of Steel AISI 4140 Covered by a Multilayer TiCN /TiNbCN, at an Impact Angle of 90°, Dyn., 2013, 80(178), p 101–108.

Title: Corrosion Properties of Heterostructured [8YSZ/Al2O3]N Coatings as a Function of the Bilayer Number
Authors: C. H. Ortiz
J. C. Caicedo
W. Aperador
Publication date: 18-10-2021
Publisher: Springer US
Published in: Journal of Materials Engineering and Performance / Issue 2/2022
Print ISSN: 1059-9495
Electronic ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-021-06300-3

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 2/2022

Elastoplastic Characterization of Zn-Cu-Ti Alloy Sheets: Experiments, Modeling, and Simulation

Tribological Behavior and Corrosion Resistance of S30432 Steel after Different Shot Peening Processes

Effect of Heat Treatment on the Microstructure and Properties of Ni-Si-B Alloy by Laser Additive Manufacturing

Impact of Carbon Fiber Reinforcement on Mechanical and Tribological Behavior of 3D-Printed Polyethylene Terephthalate Glycol Polymer Composites—An Experimental Investigation

Micro/Nanoscale Surface Modification of Ti6Al4V Alloy for Implant Applications

Super-Hydrophobic Nanostructured Silica Coating on Aluminum Substrate for Moist Air Condensation

Premium Partners