Top

Journal of Materials Engineering and Performance

Published in:

20-09-2021

Tribological Behavior and Corrosion Resistance of S30432 Steel after Different Shot Peening Processes

Authors: Ke Zhan, Yalong Zhang, Sixin Zhao, Zheng Yang, Bin Zhao, Vincent JI

Published in: Journal of Materials Engineering and Performance | Issue 2/2022

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

S30432 steel was treated by different shot peening (SP) processes, including single SP, dual SP, and triple SP. Dry sliding tribological behavior and corrosion resistance of S30432 steel after different SP processes were studied by using reciprocating friction/wear tester (Al₂O₃ as the counterpart) and electrochemical work station, respectively. The results showed that the steady-state friction coefficient could slightly decrease after triple SP process under 5 N; the low roughness value and hardened surface were responsible for it. Compared with the original S30432 steel, the wear resistance of all shot-peened samples was enhanced under the measured loads, which was mainly attributed to the high hardness of gradient hardening layers. Comparing to the as-received crystalline material, the local corrosion resistance of refined microstructure induced by dual SP and triple SP was enhanced. However, for single SP process, the corrosion resistance deteriorated, which was mainly attributed to the variation of surface roughness. It was concluded that the appropriate SP process could improve both wear and corrosion resistance.

previous article Microstructure and Properties of Cu-0.4 wt.% Al2O3 Composites Fabricated by Hot Extrusion and Cold Drawing

next article A Medium-Mn Steel Stamped Parts Overcoming Lüders Deformation by Increasing Dislocation Density

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

W.L. Li, N.R. Tao, Z. Han and K. Lu, Comparisons of Dry Sliding Tribological Behaviors between Coarse-Grained and Nanocrystalline Copper, Wear, 2012, 274–275(3), p 306–312. CrossRef

D.M. Ba, S.N. Ma, F.J. Meng and C.Q. Li, Friction and Wear Behaviors of Nanocrystalline Surface Layer of Chrome–Silicon Alloy Steel, Surf. Coat. Technol., 2007, 202(2), p 254–260. CrossRef

L. Zhou, G. Liu and Z. Han, Grain Size Effect on Wear Resistance of a Nanostructured AISI52100 Steel, Scripta Mater., 2008, 58(6), p 445–448. CrossRef

T. Balusamy, S. Kumar and T.S.N.S. Narayanan, Effect of Surface Nanocrystallization on the Corrosion Behaviour of AISI 409 Stainless Steel, Corros. Sci., 2010, 52(11), p 3826–3834. CrossRef

L. Wang and D.Y. Li, Mechanical, Electrochemical and Tribological Properties of Nanocrystalline Surface of Brass Produced by Sandblasting and Annealing, Surf. Coat. Technol., 2003, 167(2), p 188–196. CrossRef

S. Jelliti, C. Richard, D. Retraint, T. Roland, M. Chemkhi and C. Demangel, Effect of Surface Nanocrystallization on the Corrosion Behavior of Ti–6Al–4V Titanium Alloy, Surf. Coat. Technol., 2013, 224(224), p 82–87. CrossRef

Q. Sun, Q. Han, R. Xu, K. Zhao and J. Li, Localized Corrosion Behaviour of AA7150 After Ultrasonic Shot Peening: Corrosion Depth vs. Impact Energy, Corros. Sci. J. Environ. Degrad. Mater. Control, 2018, 130, p 218–230.

P. Lopez-Ruiz, M.B. Garcia-Blanco, G. Vara, I. Fernández-Pariente and S. Bagherifard, Obtaining Tailored Surface Characteristics by Combining Shot Peening and Electropolishing on 316L Stainless Steel, Appl. Surf. Sci., 2019, 492, p 1–7. CrossRef

C. Wang, C. Jiang, F. Cai, Y. Zhao, K. Zhu and Z. Chai, Effect of Shot Peening on the Residual Stresses and Microstructure of Tungsten Cemented Carbide, Mater. Des., 2016, 95, p 159–164. CrossRef

10.

K. Zhan, Y. Wu, J. Li, B. Zhao, Y. Yan, L. Xie, L. Wang and V. Ji, Investigation on Surface Layer Characteristics of Shot Peened Graphene Reinforced Al Composite by X-ray Diffraction Method, Appl. Surf. Sci., 2018, 435, p 1257–1264. CrossRef

11.

P. Zhang and J. Lindemann, Influence of Shot Peening on High Cycle Fatigue Properties of the High-Strength Wrought Magnesium Alloy AZ80, Scripta Mater., 2005, 52(6), p 485–490. CrossRef

12.

H. Ishigami, K. Matsui, Y. Jin and K. Ando, Technical Note A Study on Stress, Reflection and Double Shot Peening to Inrease Compressive Residual Stress, Fatigue Fract. Eng. Mater. Struct., 2010, 23(11), p 959–963. CrossRef

13.

C. Jiang, Z. Xu and V. Ji, Surface Layer Characteristics of SAF2507 Duplex Stainless Steel Treated by Stress Shot Peening, Appl. Surf. Sci., 2019, 481, p 226–233. CrossRef

14.

Y. Harada and K. Mori, Effect of Processing Temperature on Warm Shot Peening of Spring Steel, J. Mater. Process. Technol., 2005, 162(10), p 498–503. CrossRef

15.

E. Maleki, O. Unal and K.R. Kashyzadeh, Effects of Conventional, Severe, Over, and Re-shot Peening Processes on the Fatigue Behavior of Mild Carbon Steel, Surf. Coat. Technol., 2018, 344, p 62–74. CrossRef

16.

N.E. Uzan, R. Shlomo, R. Shneck, N. Frage and O. Yeheskel, On the Effect of Shot-Peening on Fatigue Resistance of AlSi10Mg Specimens Fabricated by Additive Manufacturing Using Selective Laser Melting (AM-SLM), Addit. Manuf., 2018, 21, p 458–464.

17.

L. Zhiming, S. Laimin, Z. Shenjin, T. Zhidong and J. Yazhou, Effect of High Energy Shot Peening Pressure on the Stress Corrosion Cracking of the Weld Joint of 304 Austenitic Stainless Steel, Mater. Sci. Eng. A, 2015, 637, p 170–174. CrossRef

18.

N.W. Khun, P.Q. Trung and D.L. Buttler, Mechanical and Tribological Properties of Shot Peened SAE 1070 Steel, Tribol. Trans., 2016, 59(5), p 932–943. CrossRef

19.

A. Toloei, V. Stoilov, D. Northwood, The relationship between surface roughness and corrosion. In: ASME 2013 International Mechanical Engineering Congress and Exposition, (2013)

20.

M.B. Leban, Č Mikyška, T. Kosec, B. Markoli and J. Kovač, The Effect of Surface Roughness on the Corrosion Properties of Type AISI 304 Stainless Steel in Diluted NaCl and Urban Rain Solution, J. Mater. Eng. Perform., 2014, 23(5), p 1695–1702. CrossRef

21.

K. Zhan, C.H. Jiang and V. Ji, Surface Mechanical Properties of S30432 Austenitic Steel After Shot Peening, Appl. Surf. Sci., 2012, 258(24), p 9559–9563. CrossRef

22.

M. Benedetti, V. Fontanari and M. Bandini, Very High-Cycle Fatigue Resistance of Shot Peened High-Strength Aluminium Alloys: Role of Surface Morphology, Int. J. Fatigue, 2015, 70(61), p 451–462. CrossRef

23.

Z. Wang, Y. Chen and C. Jiang, Thermal Relaxation Behavior of Residual Stress in Laser Hardened 17–4PH Steel After Shot Peening Treatment, Appl. Surf. Sci., 2011, 257(23), p 9830–9835. CrossRef

24.

K. Zhu, C. Jiang, Z. Li, L. Du, Y. Zhao, Z. Chai, L. Wang and M. Chen, Residual Stress and Microstructure of the CNT/6061 Composite After Shot Peening, Mater. Des., 2016, 107, p 333–340. CrossRef

25.

L.L. Santos, R.P. Cardoso and S.F. Brunatto, Direct Correlation between Martensitic Transformation and Incubation-Acceleration Transition in Solution-Treated AISI 304 Austenitic Stainless Steel Cavitation, Wear, 2020, 462–463, p 203522. CrossRef

26.

S.F. Brunatto, C.J. Scheuer, I. Boromei, C. Martini, L. Ceschini and R.P. Cardoso, Martensite Coarsening in Low-Temperature Plasma Carburizing - ScienceDirect, Surf. Coat. Technol., 2018, 350, p 161–171. CrossRef

27.

Y.G. Liu, M.Q. Li and H.J. Liu, Nanostructure and Surface Roughness in the Processed Surface Layer of Ti-6Al-4V via Shot Peening, Mater. Charact., 2017, 123, p 83–90. CrossRef

28.

K. Zhan, C.H. Jiang and V. Ji, Uniformity of Residual Stress Distribution on the Surface of S30432 Austenitic Stainless Steel by Different Shot Peening Processes, Mater. Lett., 2013, 99(20), p 61–64. CrossRef

29.

P.J. Blau, Interpretations of the Friction and Wear Break-in Behavior of Metals in Sliding Contact, Wear, 1981, 71(1), p 29–43. CrossRef

30.

L. Wang, Y. Zhao, C. Jiang, V. Ji, M. Chen, K. Zhan and F. Moreira, Investigation on Microstructure and Properties of Electrodeposited Ni-Ti-CeO 2 Composite Coating, J. Alloys Compd., 2018, 754, p 93–104. CrossRef

31.

Q. Wang, M. Callisti, J. Greer, B. Mckay, T.K. Milickovic, A. Zoikis-Karathanasis, I. Deligkiozi and T. Polcar, Effect of Annealing Temperature on Microstructure, Mechanical and Tribological Properties of Nano-sicireinforced Ni-P Coatings, Wear, 2016, 356–357, p 86–93. CrossRef

32.

K. Zhan, W.Q. Fang, B. Zhao, Y. Yan, Q. Feng and C.H. Jiang, Investigation of Surface Gradient Microstructure of Shot Peened S30432 Steel by X-ray Line Profile Analysis Method, Surf. Rev. Lett., 2017, 24(06), p 150. CrossRef

33.

J. Mølgaard, A discussion of Oxidation, Oxide Thickness and Oxide Transfer in Wear, Wear, 1976, 40(3), p 277–291. CrossRef

34.

T. Wang, J. Yu and B. Dong, Surface Nanocrystallization Induced by Shot Peening and its Effect on Corrosion Resistance of 1Cr18Ni9Ti Stainless Steel, Surf. Coat. Technol., 2006, 200(16), p 4777–4781. CrossRef

35.

V. Azar, B. Hashemi and M.R. Yazdi, The Effect of Shot Peening on Fatigue and Corrosion Behavior of 316L Stainless Steel in Ringer’s Solution, Surf. Coat. Technol., 2010, 204(21), p 3546–3551. CrossRef

36.

C. Wang, C. Jiang, Z. Chai, M. Chen, L. Wang and V. Ji, Estimation of Microstructure and Corrosion Properties of Peened Nickel Aluminum Bronze, Surf. Coat. Technol., 2017, 313, p 136–142. CrossRef

Title: Tribological Behavior and Corrosion Resistance of S30432 Steel after Different Shot Peening Processes
Authors: Ke Zhan
Yalong Zhang
Sixin Zhao
Zheng Yang
Bin Zhao
Vincent JI
Publication date: 20-09-2021
Publisher: Springer US
Published in: Journal of Materials Engineering and Performance / Issue 2/2022
Print ISSN: 1059-9495
Electronic ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-021-06249-3

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 2/2022

Effects of Keyhole Tungsten Inert Gas Welding Parameters on 2205 Duplex Stainless Steel Welded Joints

Microstructure and Wear Properties of Electrodeposited Ni-B-Al2O3 Composite Coating on Low Carbon Steel at Elevated Temperature

Impact of Carbon Fiber Reinforcement on Mechanical and Tribological Behavior of 3D-Printed Polyethylene Terephthalate Glycol Polymer Composites—An Experimental Investigation

Micro/Nanoscale Surface Modification of Ti6Al4V Alloy for Implant Applications

Tribological Properties and Friction-Induced Noise Performance of M50 with Curved Microchannels Filled by Sn-Ag-Cu and Ti3C2

Preparation of Antibacterial and Strengthened High-Density Polyethylene Composites via Compounding with Silver Ion Glass Microbead-Loaded Basalt Fiber

Premium Partners