nach oben

Erschienen in:

2019 | OriginalPaper | Buchkapitel

Modeling and Experimental Study of Surfaces Optoelectronic Elements from Crystal Materials in Polishing

verfasst von : Yu. D. Filatov

Erschienen in: Simulation and Experiments of Material-Oriented Ultra-Precision Machining

Verlag: Springer Singapore

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

Based on investigations of the mechanism of precision surface formation in workpieces of anisotropic monocrystalline materials for optoelectronics, a generalized model of material removal in polishing with suspensions of polishing powders has been constructed. The removal rate in polishing sapphire planes of different crystallographic orientations has been found to grow in the series m < c < a < r with increasing volume, surface area, and most probable size of debris particles as well as with energy of dispersion of material from the face being polished. A study of the mechanism of formation of monocrystal planes of different crystallographic orientations has revealed that in polishing of sapphire the surface roughness parameters Ra, Rq, Rmax decrease in the series c > r > m > a with decreasing dielectric permittivity and thermal conductivity coefficient of the workpiece material, debris particle height, and Lifshitz constant. As a result, studies of regularities mechanical polishing optoelectronic components of crystalline materials found that polishing efficiency decreases with an increase of the binding energy and the transfer energy. It is shown that the polishing efficiency increases with increasing heat conduction coefficient of the material being processed, a processed surface road friction element by lapping and Lifshitz force. It is found that the ratio of the volume wear coefficient to the temperature conductivity coefficient of the material being processed depends on the specific heat and the transfer energy. The relative roughness of the treated surfaces of silicon carbide crystals, gallium nitride, aluminum nitride, and sapphire is characterized by the ratio: 0.68:0.67:0.63:1.00.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Vorheriges Kapitel Cutting Mechanism and Surface Formation of Ultra-Precision Raster Fly Cutting

Nächstes Kapitel Advanced Applications of Elliptical Vibration Cutting in Micro/Nanomachining of Difficult-to-Cut Materials

Filatov YuD, Vetrov AG, Sidorko VI, Filatov OYu, Kovalev SV (2013) A mechanism of diamond-abrasive finishing of monocrystalline silicon carbide. J Superhard Mater 35(5):303–308CrossRef

Prikhna TA, Starostina AV, Lizkendorf D et al (2014) Studies of the oxidation stability, mechanical characteristics of materials based on max phases of the Ti–Al–(C, N) systems, and of the possibility of their use as tool bonds and materials for polishing. J Superhard Mater 36(1):9–17CrossRef

Filatov YuD, Vetrov AG, Sidorko VI, Filatov OYu et al (2015) Polishing of optoelectronic components made of monocrystalline silicon carbide. J Superhard Mater 37(1):48–56CrossRef

Filatov OYu, Sidorko VI, Filatov YuD (2007) Special features of macro- and microrelief formation in nonmetallic flat surfaces in diamond grinding. J Superhard Mater 29(6):361–368CrossRef

Filatov YuD, Sidorko VI, Filatov OYu et al (2009) Surface roughness in diamond abrasive finishing. J Superhard Mater 31(3):191–195CrossRef

Filatov YD, Sidorko VI, Filatov OYu, Yaschuk VP, Heisel U, Storchak M (2009) Surface quality control in diamond abrasive finishing. Measurement Systems for Industrial Inspection VI, Proceedings of SPIE, 2009, vol 7389, art. 73892O (9)

Filatov OYu, Poperenko LV (2006) In situ ellipsometry of surface layer of nonmetallic transparent materials during its finish processing. Appl Surf Sci 253(1):163–166CrossRef

Filatov YuD, Yashchuk VPFilatov OYu, Heisel U, Storchak M, Monteil G (2009) Assessment of surface roughness and reflectance of nonmetallic products upon diamond abrasive finishing. J Superhard Mater 31(5), art. 338

Filatov YuD, Filatov OYu, Heisel U, Storchak M, Monteil G (2010) In situ control of roughness of processed surfaces by reflectometric method. Optical Micro- and Nanometrology III, Proceedings of SPIE, vol 7718, art. 77181 J (9)

10.

Filatov YuD, Filatov AYu, Syrota OO et al (2010) The influence of tool wear particles scattering in the contact zone on the workpiece surface microprofile formation in polishing quartz. J Superhard Mater 32(6):415–422CrossRef

11.

Filatov YuD, Sidorko VI (2011) Localization of fragments of a deposit on the workpiece surface in polishing nonmetallic materials. J Superhard Mater 33(5), art. 340CrossRef

12.

Filatov YuD, Monteil G, Sidorko VI, Filatov OYu (2013) Formation of a deposit on workpiece surface in polishing nonmetallic materials. Smart Sensors, Actuators, and MEMS VI. Proceedings of SPIE, vol 8763, art. 876336 (15)

13.

Zhu H, Tessaroto LA, Sabia R, Greenhut VA, Smith M, Niesz DE (2004) Chemical mechanical polishing (CMP) anisotropy in sapphire. Appl Surf Sci 236(1–4):120–130CrossRef

14.

Budnikov AT, Vovk EA, Krivonogov SI, Danko AYa, Lukiyenko OA (2010) Anisotropy of sapphire properties associated with chemical-mechanical polishing with silica. Funct Mater 17(4):488–494

15.

Wang Y, Liuu S, Peng G, Zhou S, Xu J (2005) Effects of surface treatment on sapphire substrates. J Crystal Growth 274:241–245CrossRef

16.

Li Y, Wu Y, Wang J, Yang W, Guo Y, Xu Q (2012) Tentative investigation towards precision polishing of optical components with ultrasonically vibrating bound-abrasive pellets. Opt Express 20(1):568–575CrossRef

17.

Zhou C, Zhang Q, He C, Li Y (2014) Function of liquid and tool wear in ultrasonic bound-abrasive polishing of fused silica with different polishing tools. Opt-Int J Light Electron Opt 125(15):4064–4068CrossRef

18.

Filatov YuD (2008) Bound-abrasive polishing of precision surfaces of nonmetallic materials. J Superhard Mater 30(1), art. 44

19.

Filatov YuD, Filatov OYu, Monteil G, Heisel U, Storchak MG (2011) Bound-abrasive grinding and polishing of surfaces of optical materials. Opt Eng 50(6), art. 063401CrossRef

20.

Filatov YuD, Filatov OYu, Monteil G, Heisel U, Storchak M (2010) Bound-abrasive grinding and polishing of surfaces of optical materials. Current developments in lens design and optical engineering XI; and advances in thin film coatings VI, Proceedings of SPIE, 2010, vol 7786, art. 778613 (9)

21.

Chen XF, Siche D, Albrecht M, Hartmann C, Wollweber J, Xu XG (2008) Surface preparation of AlN substrates. Crystal Res Technol 43(6):651–655CrossRef

22.

Vovk EA, Budnikov AT, Nizhankovskyi SV et al (2013) Polishing of AlN/sapphire substrate obtained by thermochemical nitridation of sapphire. Funct Mater 20(2):253–258CrossRef

23.

Satoh I, Arakawa S, Tanizaki K, Miyanaga M, Sakurada T, Yamamoto Y, Nakahata H (2010) Development of aluminum nitride single-crystal substrates. SEI Techn Rev 71:78–82

24.

Ling Y, Low-damage grinding. In: Polishing of silicon carbide surfaces: SIMTech Technical Report (PT/01/001/PM)

25.

Aida H, Takeda H, Kim S-W, Aota N, Koyama K, Yamazaki T, Doi T (2014) Evaluation of subsurface damage in GaN substrate induced by mechanical polishing with diamond abrasives. Appl Surf Sci 292:531–536CrossRef

26.

Nowak G, Xia XH, Kelly JJ, Weyher JL, Porowski S (2001) Electrochemical etching of highly conductive GaN single crystals. J Cryst Growth 222:735–740CrossRef

27.

Golabczak M (2011) Polishing of hard machining semiconductor materials made of silicon carbide. Mech Mech Eng 15(1):81–93

28.

Deng Hui, Hosoya Kenji, Imanishi Yusuke, Endo Katsuyoshi, Yamamura Kazuya (2015) Electro-chemical mechanical polishing of single-crystal SiC using CeO₂ slurry. Electrochem Commun 52:5–8CrossRef

29.

Filatov OYu, Sidorko VI, Kovalev SV et al (2016) Polishing substrates of single-crystal silicon carbide and sapphire for optoelectronics. Funct Mater 23(1):104–110CrossRef

30.

Filatov YuD (2017) Diamond polishing of crystalline materials for optoelectronics. J Superhard Mater 39(6):427–433CrossRef

31.

Li Yaguo, Yongbo Wu, Zhou Libo, Fujimoto Masakazu (2014) Vibration-assisted dry polishing of fused silica using a fixed-abrasive polisher. Int J Machine Tools Manufact 77:93–102CrossRef

32.

Budnikov AT, Vovk EA, Kanishchev VN, Krivonogov SI (2012) Investigation of residual stresses in sapphire plates after grinding and polishing. Funct Mater 19(4):478–482

33.

Yan W, Zhang Z, Guo X, Liu W, Song Z (2015) The effect of pH on sapphire chemical mechanical polishing. ECS J Solid State Sci Technol 4(3):108–111CrossRef

34.

Vovk EA (2015) Chemical-mechanical polishing of sapphire by polishing suspension based on aerosol. Funct Mater 22(2):252–257CrossRef

35.

Vovk EA (2015) Deagglomeration of aerosil in polishing suspension for chemical-mechanical polishing of sapphire. Funct Mater 22(1):110–115MathSciNetCrossRef

36.

Filatov YuD (2001) Polishing of aluminosilicate materials with bound-abrasive tools. Sverkhtverdye Materialy 23(3):36–49 (J Superhard Mater 2001, no. 3)

37.

Filatov YuD, Sidorko VI (2005) Statistical approach to wear of nonmetallic workpiece surfaces in polishing. Sverkhtverdye Materialy 27(1):58–66 (J Superhard Mater 2005, no. 1)

38.

Filatov OYu, Sidorko VI, Kovalev SV, Filatov YuD, Vetrov AG (2016) Material removal rate in polishing anisotropic monocrystalline materials for optoelectronics. J Superhard Mater 38(2):123–131CrossRef

39.

Bakholdin SI, Maslov VN (2015) Modeling of surface energies of sapphire crystals. Fiz Tverd Tela 57(6):1213–1219

40.

Vodenitcharova T, Zhang LC, Zarudi I, Yin Y, Domyo H, Ho T, Sato M (2007) The effect of anisotropy on the deformation and fracture of sapphire wafers subjected to thermal shocks. J Mater Proc Tech 194:52–62CrossRef

41.

Dobrovinskaya ER, Litvinov LA, Pishchik VV (2004) Entsiklopediya sapfira (Encyclopedia of Sapphire). Institute for Monocrystals, National Academy of Sciences of Ukraine, Kharkov

42.

Barybin AA, Tomilin VI, Shapovalov VI (2011) Fiziko-tehnologicheskie osnovy makro-, mikro, i nanoelektroniki (Physical-Technological Fundamentals of Macro-, Micro-, and Nanoelectronics). Fizmatlit, Moscow

43.

Kadleikova M, Breza J, Vesely M (2001) Raman spectra of synthetic sapphire. Microelectron J 32:955–958CrossRef

44.

Fainer NI, Kosinova ML, Rumyantsev YuM (2001) Thin films of silicon and boron carbonitrides. Synthesis, investigation of composition and structure, Ros. Khim. Zhurn. Obshch. im. D. I. Mendeleeva vol XLV, no 3, pp 101–108

45.

Gerasimov SA, Dmitrieva NM, Kosareva TA (2013) A study of machining of leucosapphire. Nauch-Tekhn Zhurn Kontenant 12(2):84–89

46.

Filatov YuD (1991) The mechanism of the surface microrelief formation in glass polishing. Sverkhtverdye Materialy 5:61–65 (J Superhard Mater 1991, no. 5)

47.

Cuccureddu F, Murphy S, Shvets IV, Porcu M, Zandberger HW, Sidorov NS, Bozhko SI (2010) Surface morphology of c-plane sapphire (α-alumina) produced by high temperature anneal. Surf Sci 604:1294–1299CrossRef

48.

Butashin AV, Vlasov VP, Kanevskii VM, Muslimov AE, Fedorov VA (2012) Specific features of the formation of terrace-step nanostructures on the (0001) surface of sapphire crystals. Crystallogr Rep 57(6):824–830CrossRef

49.

Filatov OYu, Sidorko VI, Kovalev SV, Filatov YuD, Vetrov AG (2016) Polished surface roughness of optoelectronic components made of monocrystalline materials. J Superhard Mater 38(3):197–206CrossRef

50.

Kats EI (2015) Van der Waals, Casimir, and Lifshitz forces in soft substances. Usp Fiz Nauk 185(9):964–969CrossRef

51.

Rekhviashvili SSh (2007) The application of fractional integro-differentiation for calculating thermodynamical properties of surfaces. Fiz Tverd Tela 49(4):756–759

52.

Voloshin AE, Rashkovich LN, Rudneva EB, Manomenova VL (2014) Growing the crystals. Priroda 10:62–72

53.

Rogov VV, Filatov YD, Kottler W, Sobol VP (2001) New technology of precision polishing of glass optic. Opt Eng 40(8):1641–1645CrossRef

54.

Filatov YuD, Rogov VV (1994) A cluster model of fatigue wear mechanism of SiO₂-containing materials in polishing with tools containing bound ceria-based polishing powders. Part 1. Sverkhtverdye Materialy 3:40–43 (J Superhard Mater 1994, no. 3)

55.

Deryagin BV, Abrikosova II, Lifshitz EM (2015) Molecular attraction of condensed bodies. Usp Fiz Nauk 185(9):981–1001CrossRef

56.

Lee HS, Jeong HD, Dornfeld DA (2013) Semi-empirical material removal rate distribution model for SiO₂ chemical mechanical polishing (CMP) processes. Precis Eng 37:483–490CrossRef

57.

Harima H (2002) Properties of GaN and related compounds studied by means of Raman scattering. J Phys: Condens Matter 14:967–993

58.

Davydov VYu, Kitaev YuE, Goncharuk IN et al (1998) Phonon dispersion and Raman scattering in hexagonal GaN and AlN. Phys Rev B 58(19):12899–12907CrossRef

59.

Quay R (2008) Gallium nitride electronics. Springer, Berlin

60.

Asghar K, Qasim M, Das D (2014) Effect of polishing parameters on chemical mechanical planarization of C-plane (0001) gallium nitride surface using SiO₂ and Al₂O₃ abrasives. ECS J Solid State Sci Technol 3(8):277–284CrossRef

61.

Filatov YuD (2018) Surface roughness of optoelectronic components in mechanical polishing. J Superhard Mater 40(1):52–57CrossRef

Titel: Modeling and Experimental Study of Surfaces Optoelectronic Elements from Crystal Materials in Polishing
verfasst von: Yu. D. Filatov
Verlag: Springer Singapore
Buch: Simulation and Experiments of Material-Oriented Ultra-Precision Machining
Print ISBN: 978-981-13-3334-7

Electronic ISBN: 978-981-13-3335-4

Copyright-Jahr: 2019
DOI: https://doi.org/10.1007/978-981-13-3335-4_6

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht