nach oben

Erschienen in:

2019 | OriginalPaper | Buchkapitel

34. Toughening Mechanisms on Recycled Rubber Modified Epoxy Based Composites Reinforced with Alumina Fibers

verfasst von : A. B. Irez, I. Miskioglu, E. Bayraktar

Erschienen in: Mechanics of Composite, Hybrid and Multifunctional Materials, Volume 5

Verlag: Springer International Publishing

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

Environmental and economic concerns has been a motivation for the material manufacturers to produce new, robust, lightweight and cost-effective materials. Therefore, aeronautic and automobile industries are investigating multifunctional composite materials that can meet their expectations. In this regard, polymer based composites can have high specific strength with the contribution of resistant fillers. As a polymer, epoxy is considered an appropriate matrix, which can be modified by different agents. First option is the addition of hard particles and second is that the inclusion of thermoplastics or the addition of elastomeric materials. Since, epoxy exhibits high brittleness due to its highly cross-linked nature, modifiers less rigid than the matrix can serve as unique tougheners enhancing the ductility. In this study, a good combination of both hard and soft modifiers is used. In addition to mechanical characteristics, using of fresh clean scrap EPDM rubbers adds an economic and environmental value to this study. Also, due to its favorable structural characteristics such as interlocking effects of fibers, addition of alumina fibers (AF) ensures desired mechanical properties in case of a homogeneous distribution. This paper primarily explains the mechanical behavior as well as damage mechanisms of epoxy-fresh scrap rubber composites. The mechanical and physical properties of these composite systems are studied in the present work. Dynamic Mechanical Analysis (DMA) analyses were carried out to determine thermal-mechanical properties. Three-point bending and fracture toughness tests were realized with single edge notched beam (SENB) and smooth specimens. Finally, scanning electron microscope (SEM) was used to observe fracture surfaces and the microstructure.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Vorheriges Kapitel Sub-components of Wind Turbine Blades: Proof of a Novel Trailing Edge Testing Concept

Nächstes Kapitel Toughening Mechanisms on Recycled Rubber Modified Epoxy Based Composites Reinforced with Graphene Nanoplatelets

McGrath, L.M., Parnas, R.S., King, S.H., Schroeder, J.L., Fischer, D.A., Lenhart, J.L.: Investigation of the thermal, mechanical, and fracture properties of alumina–epoxy composites. Polymer. 49, 999–1014 (2008)CrossRef

Zaimova, D., Bayraktar, E., Miskioglu, I., Dishovsky, N., Katundi, D.: Epoxy resin reinforced scrap rubber composites used for aeronautical applications, SEM-2013, Annual Conference – Experimental and Applied Mechanics, The Westin Lombard Yorktown Center Lombard, IL, June 3–5, 2013, 1, 1, 1–9, ed. SEM/Springer-Link (2013)

Wetzel, B., Rosso, P., Haupert, F., Friedrich, K.: Epoxy nanocomposites – fracture and toughening mechanisms. Eng. Fract. Mech. 73, 375–398 (2006)CrossRef

Zaimova, D., Bayraktar, E., Miskioglu, I.: Design and manufacturing of new elastomeric composites: mechanical properties, chemical and physical analysis Int. J. Compos. Part B Elsevier USA 1, 1, 1–12, November 2016, on line (2017)

Garg, A.C., Mai, Y.-W.: Failure mechanisms in toughened epoxy resins—a review. Compos. Sci. Tech. 31, 179–223 (1988). https://doi.org/10.1016/0266-3538(88)90009-7 CrossRef

Lee, J., Yee, A.F.: Inorganic particle toughening I: micro-mechanical deformations in the fracture of glass bead filled epoxies. Polymer. 42, 577–588 (2001). https://doi.org/10.1016/S0032-3861(00)00397-9 CrossRef

Irez, A.B., Bayraktar, E., Miskioglu, I.: Mechanical characterization of epoxy – scrap rubber based composites reinforced with alumina fibers. In: Mechanics of Composite and Multi-functional Materials, vol. 6, pp. 59–70. Springer, Cham (2017)

Zaimova, D., Bayraktar, E., Miskioglu, I., Dishovsky, N.: Wear resistance of elastomeric based composites by continuous multi-cycle indentation used in manufacturing engineering. Adv. Mater. Res. 939, 106–113 (2014., Trans Tech Publications, Switzerland). https://doi.org/10.4028/www.scientific.net/AMR.939.106 CrossRef

Nakamura, Y., Yamaguchi, M., Okubo, M., Matsumoto, T.: Effects of particle size on mechanical and impact properties of epoxy resin filled with spherical silica. J Appl Polym Sci. 45, 1281–1289 (1992)CrossRef

10.

Okazaki, M., Murota, M., Kawaguchi, Y., Tsubokawa, N.: Curing of epoxy resin by ultrafine silica modified by grafting of hyperbranched polyamidoamine using dendrimer synthesis methodology. J. Appl. Polym. Sci. 80, 573–579 (2001). https://doi.org/10.1002/1097-4628(20010425)80:4<573::AID-APP1132>3.0.CO;2-E CrossRef

11.

Zaimova, D., Bayraktar, E., Katundi, D., Dishovsky, N.: Study of the influence of SiC and Al2O3 as reinforcement elements in elastomeric matrix composites, JAMME-2013, International-Annual Conference of WAMME(Academy of Science), Krakow-Poland, 23–26 June 2013, 1, 1, 1–9, ed. WAMME-JAMME, (2013), ISSN 1734-8412

12.

Wetzel, B., Haupert, F., Qiu, Z.M.: Epoxy nanocomposites with high mechanical and tribological performance. Compos. Sci. Technol. 63, 2055–2067 (2003). https://doi.org/10.1016/S0266-3538(03)00115-5 CrossRef

13.

Bayraktar, E., Miskioglu, I., Zaimova, D.: Low-cost production of epoxy matrix composites reinforced with scarp rubber, boron, glass bubbles and alumina. Mech. Compos. Multifunct. Mater. Springer- USA. 7(1), 163–172., ed. Kristin B. Zimmerman, Springer-USA (2015)

14.

Zee, R.H., Huang, Y.H., Chen, J.J., Jang, B.Z.: Properties and processing characteristics of dielectric-filled epoxy resins. Polym Compos. 10, 205–214 (1989). https://doi.org/10.1002/pc.750100402 CrossRef

15.

Ferreira, L.M.P., Miskioglu, I., Bayraktar, E., Katundi, D.: Mechanical and tribological properties of scrap rubber reinforced with Al2O3 fiber, aluminium and TiO2, Conference proceedings of the society for experimental mechanics series, vol. 7, pp. 37–44. Springer (2016). https://doi.org/10.1007/978-3-319-41766-0

16.

Zaimova, D., Bayraktar, E., Tan, M-J., Miskioglu, I., Katundi, D.: Design of multifunctional energetic structural composites: a preliminary study on an epoxy-rubber matrix with exothermic mixture reinforcements, SEM-2013, Annual Conference – Experimental and Applied Mechanics, The Westin Lombard Yorktown Center Lombard, IL, USA, June 3–5, 2013, 1, 1, 1–8, ed. SEM/Springer-Link (2013)

17.

Jin Kim, D., Hyun Kang, P., Chang, N.Y.: Characterization of mechanical properties of γAl2O3 dispersed epoxy resin cured by γ-ray radiation. J Appl Polym Sci. 91, 1898–1903 (2004). https://doi.org/10.1002/app.13250 CrossRef

18.

Arayasantiparb, D., McKnight, S., Libera, M.: Compositional variation within the epoxy/adherend interphase. J. Adhes. Sci. Technol. 15, 1463–1484 (2001). https://doi.org/10.1163/156856101753213312 CrossRef

19.

Landel, R.F., Nielsen, L.E.: Mechanical Properties of Polymers and Composites, 2nd edn. CRC Press, New York (1993)

20.

Irez, A.B., Miskioglu, I., Bayraktar, E.: Mechanical characterization of epoxy – scrap rubber based composites reinforced with nano graphene. Springer Link, Mech. Compos. Multi-funct. Mat. 6, 45–58 (2017., ISBN 978-3-319-63,408-1). https://doi.org/10.1007/978-3-319-63,408-1 CrossRef

21.

Rothon, R.: Particulate-filled Polymer Composites. iSmithers Rapra Publishing, Shawbury (2003)

22.

Rothon, R.N.: Mineral Fillers in Thermoplastics: Filler Manufacture and Characterisation. Mineral Fillers in Thermoplastics I, pp. 67–107. Springer, Berlin, Heidelberg (1999). https://doi.org/10.1007/3-540-69220-7_2 CrossRef

23.

Branch, M.: Preparation of nano-scale α-Al2O3 powder by the sol-gel method. Ceram. Silic. 55, 378–383 (2011)

24.

Amirshaghaghi, A., Kokabi, M.: Tailoring size of α-Al2O3 n nano powders via polymeric gel-net method. Iran. Polym. J. 19, 615–624 (2010)

25.

Zhang, Z., Lei, H.: Preparation of α-alumina/polymethacrylic acid composite abrasive and its CMP performance on glass substrate. Microelectron. Eng. 85, 714–720 (2008)CrossRef

26.

Irez, A.B., Miskioglu, I., Bayraktar, E.: Mechanical characterization of epoxy: scrap rubber based composites reinforced with nanoparticles. Springer Link, Mech. Compos. Multi-funct. Mat. 6, 33–44 (2017., ISBN 978-3-319-63,408-1). https://doi.org/10.1007/978-3-319-63,408-1 CrossRef

Titel: Toughening Mechanisms on Recycled Rubber Modified Epoxy Based Composites Reinforced with Alumina Fibers
verfasst von: A. B. Irez
I. Miskioglu
E. Bayraktar
Verlag: Springer International Publishing
Buch: Mechanics of Composite, Hybrid and Multifunctional Materials, Volume 5
Print ISBN: 978-3-319-95509-4

Electronic ISBN: 978-3-319-95510-0

Copyright-Jahr: 2019
DOI: https://doi.org/10.1007/978-3-319-95510-0_34

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht