An analysis on the slaking and disintegration extent of weak rock mass of the water tunnels for hydropower project using modified slake durability test

In underground engineering, the environmental condition is highly controlled by the type of construction project with respect to the exposure of rocks to moisture, temperature and air, and especially the periodical changes on these parameters. Heterogeneous rock mass undergone different degrees of metamorphism and weathering exhibit changed geotechnical properties related to disintegration and degradation when exposed to environmental agents (Cano et al. 2017; Vivoda Prodan and Arbanas 2016) such as air and water. Caution is required for the prediction of the response of the rock material to the disturbances brought up by the excavation, as this depend on the present weathering state and the rate at which the properties change in response to the environmental changes (Czerewko and Cripps 2001). Therefore, selection of appropriate test procedures will help to improve the assessment of long-term durability.

The major difference in water tunnels compared with other underground engineering projects is the intensity of exposure to water during the life-time of the project. The rock mass is first at the stage of drained condition during construction period due to contentious ventilation and heat released by the moving construction equipment. Once the construction is completed, the waterway system (tunnels) is filled with water for the generation of hydro-electricity. Dewatering of the waterway system is carried out periodically to inspect the stability condition of the tunnels which mainly are supported by thick layers of sprayed concrete (shotcrete). During operation, the rock mass near the tunnel periphery and below the hydrostatic line is fully saturated. For the time of the operational life of the hydropower plant, several watering and dewatering cycles will take place. The cycles of dewatering are relatively short, and the temperature is relatively stable, resulting in draining effects rather than a complete dry-out of the rocks near the tunnel periphery. This periodical exposure to wetting and draining is assumed to amplify the weakening and degradation of the rock material, especially the weak and/or clay bearing rocks. In addition, the water tunnels for hydropower are subjected to dynamic pressure fluctuations caused by cyclic change in the production magnitude of the power plant. The response of the rock mass to complete saturation, cyclic drainage under relatively stable temperature conditions, and dynamic pressure fluctuations are of main interest when assessing the degradation behavior of the rocks which influences the long-term stability of the water tunnels.

Franklin and Chandra (1972) developed a slake durability test methodology at laboratory scale where the boundary conditions are standardized for quantification and comparison purposes. The technique itself has been discussed in detail by Franklin and Chandra (1972), Koncagül and Santi (1999), Czerewko and Cripps (2001), Erguler and Ulusay (2009) and is also the ISRM suggested method for determination of the slake-durability index (ISRM 1979). The test procedure is designed in such a way that the samples are first completely dried, which is achieved by leaving the prepared lumps in an oven at 105 °C until no more weight loss, whereby 2–6 h are regarded as sufficient time (ISRM 1979). After drying, the samples are kept in a specially designed drum for a wetting period of 10 min in a slow rotating mode. The samples are again dried in the oven and weighted, and the material loss is measured. The method aims to accelerate weathering to a maximum by combining the processes of slaking and sieving whereby the latter requires some motion in the test process.

In general, it is fair agreement between a low durability and high degree of disintegration. Although material has broken down during the test, a high slake durability index value may arise because it is not recorded as having done so if it does not pass through the 2-mm mesh test drum (Czerewko and Cripps 2006). In fact, the prepared lumps prior to the slake durability test have a diameter of approximately 30–50 mm, and extensive disintegration may occur within the span of particle sizes greater than 2 mm. In addition, the shape of the grains comprising the retained material may produce misleading results since splintered grains less likely pass the 2-mm square openings of the mesh. This means that the slake durability index is not necessarily reflecting the actual disintegration degree during the test, and rocks with similar slake durability index may show very different disintegration behavior.

Franklin and Chandra (1972) thoroughly explained the rationale of the suggested test with the description of different features of the testing procedure. They argued that other processes than climatic wetting and drying, such as mechanical abrasion, leaching, solution, and chemical alteration, can locally result in short-term damage where the environment is particularly severe or where the rock is already in an advance state of “geological” weathering. Further, they stated that the ideal way of assessing the slake durability is to compare complete particle-size distributions before and after slaking, but concluded that for most practical purposes, a single sieve gives a satisfactory index.

The suggested modifications of the ISRM slake durability test are based on the extraordinary conditions met in a water tunnel discussed in “The environmental setting of waterway tunnels for hydropower”-section. The modified test has the same framework and follows similar standardized steps as the ISRM test with two main deviating boundary conditions. First, the lump samples are immersed in water to achieve full saturation prior to the first cycle of rotation in the drum, and then the samples are drained at 30 °C between the cycles instead of drying at high temperatures as suggested in ISRM (1979). Draining is performed by leaving the samples in a drying cabinet for 24 h between the cycles. The samples will not be completely dried out neither will they be exerted to temperatures higher than what is expected maximum during the construction of the tunnels. In order to calculate the slake durability index, however, dehydration is accomplished by drying the samples at 50 °C as a part of the preparation and additionally after the completed test. This enables a comparison of the slake durability indices obtained from both test methods. In addition, a particle size distribution analysis on the material after a completed test procedure is introduced in order to assess the actual degree of disintegration, which may vary between different rock types.

The flysch sequences contain claystone, siltstone, marls, and sandstones with varying degrees of weathering and alterations (Selen and Panthi 2018). The material is best described as very heterogeneous in terms of color and fabric, with sections of intact cores alternating with sections of partly or totally disintegrated rock material (Fig. 1). The heterogeneous nature of the flysch results in a great variation of material properties within meters down to centimeters of the material. In terms of evaluating the locational degradation potential of the rock mass surrounding a tunnel, it is not distinguished between claystone, siltstone, sandstone, marl, or other sub-types of rock material type in this connection.

The ophiolitic rock mass comprehends highly weathered serpentinite. Serpentinite forms as a result of serpentinization of ultramafic rocks by hydration of ferromagnesian silicate minerals during low-temperature metamorphic processes (Moody 1976). The common alteration assemblage produced by serpentinization is lizardite, chrysotile, and kaolinite, occasionally together with brucite, antigorite, and clay minerals. The material is of moderately disintegrated to lumps of variating sizes, but otherwise apparently homogenous in terms of color and fabric (Fig. 2).

The nature of these two rock types are complex, resulting from their depositional and tectonic history, which means that they cannot easily be classified in terms of widely used rock mass classification systems. Both rock types are categorized as weak and contains clay minerals, which means they are vulnerable to exposure to environmental conditions and weathering.

Despite of varying material composition, one core meter of rock material is regarded as a sample representing the expected behavior of this rock type at the particular section of the tunnel. Some segments of the sample material are strong and required further preparation to achieve lumps of appropriate shape and sizes. Other segments included splintered and weak material, and preparation of lumps had to be done carefully to not to shatter the whole sample to splinters. Fig. 3a–c illustrates the outcome of the preparation of sample Flysch 8.

The serpentinite material is already disintegrated to lump-sizes at arrival. At some locations, the lumps were too small compared with the preferred sizes for the slake durability test, i.e., less than 40 g. Therefore, lumps with sizes 40–60 g were chosen from one to two core meters at these locations. An overview of all the selected samples and visual characteristics, including heterogeneity, is given in Table 1.

The first step in detecting the potential of a rock to degrade and slake is to evaluate the mineralogical composition of the rock itself. X-ray diffraction (XRD) analysis is a method used in identifying and determining the mineralogical composition of the rock samples. It is common to perform a bulk analysis of the mineralogical content, and then treat the fine-fraction powder of the material with ethylene glycol to detect swelling minerals. Every mineral or compound has a characteristic X-ray diffraction pattern, call it “fingerprint”, which can be matched against a database of over thousands of recorded phases (Dutrow and Clark 2012). Identification and quantification of minerals is carried out by comparing relative peak heights of the crystalline phases. However, weathering may cause a destruction of the crystalline structures of the minerals, seen as amorphous reflections in the X-ray diffraction patterns. Although a semi-quantitative deviation between crystalline and amorphous phases is approximate and questionable (Tijhuis 2018), it reveals valuable information on the variable degree of weathering of the samples.

The XRD analysis was conducted at NTNU with a Bruker D8 ADVANCE. Only crystalline phases were quantified, while a semi-quantitative deviation between crystalline and amorphous phases is performed to indicate the amount of weathered minerals. Identification of crystalline phases is done with DIFFRAC.SUITE.EVA software combined with PDF-4+ database. Quantification of the minerals is done by Rietveld refinement in Topas with an accuracy of 1–2 percent (%). Further, glycolation is used on fraction sizes of < 6 μm to identify swelling clays, but quantification on the amount of swelling minerals based on this method is highly questionable and is not performed. The detected swelling minerals are therefore only indicated as “detected” or “not detected”.

It is assumed that the most moisture sensitive rock components are clay minerals as smectite and kaolinite. In addition, clay-like minerals such as chlorite and mica are susceptible to weathering agents and may transform into clay minerals or intermediate states of these mineral groups (Wilson 2004). To enable a distinction between the different moisture sensitive minerals and their properties, pervasive mineral and swelling analyses must be confirmed. In this study, in terms of defining moisture sensitive rock components in the context of the slake durability assessment, it is not distinguished between clays and clay-like minerals.

The sample is placed in a clean drum with a standard mesh of 2 mm and dried to a constant weight at 105 °C (A). The drum plus the sample is then put in the slaking container with tap water at 20–25 °C, and the drum is rotated at 20 rpm for 10 min. The drum plus the retained portion of the sample is removed from the container and dried to a constant weight at 105 °C (C₁). The procedure is repeated, and the dry weight C₂ of the drum plus retained portion of the sample is recorded. The dry weight of the drum, D, is then used to calculate the slake-durability index (SDI) of the sample after two cycles of drying and wetting. The slake-durability index (SDI) is the percentage ratio of final to initial dry weights of rock in the drum:

The slake durability test as suggested by ISRM (1979) uses the second cycle as slake durability index (SDI₂) in the assessment of the degradation potential of rocks, which describe the short-term effect of wetting and drying. For long-term evaluations, the cycles can be repeated i times to better reflect the evolution of weathering over time. As suggested by Selen and Panthi (2018), the above formula can be extended to apply for i cycles of drying and wetting:

The number of cycles used in this study is 4, where 2 h of drying between the cycles is chosen of practical reasons as explained previously. Minor amounts of water may be retained after 2 h; therefore, an extended phase of drying is included after the last cycle and before the final calculation of SDI₄.

As a part of the preparation, the sample is placed in a clean glass container and dried in a drying cabinet at 50 °C until no more weight loss, and the initial dry weight of the sample plus the dry drum is recorded (A). The static wetting phase is then performed by leaving the samples in a container filled with tap-water having temperature between 20 and 25 °C for 72 h. Visual signs of disintegration are described and photographed. The wetting phase is not regarded as a part of the slake durability test itself but rather a separate phase after preparation of the lumps and prior to the first cycle.

After the static wetting phase, the sample is gently moved from the glass container to a clean and wetted drum (D (wet)) with a standard mesh of 2 mm. This is performed by placing the drum in a glass container and carefully pouring the sample and water solution into the drum, whereby the portion of the sample > 2 mm is sieved by the drum mesh. Dependent on the rock type, some of the material dissolve and/or disintegrate to less than 2 mm and is therefore removed from the sample before the first slake cycle. This material is dried and recorded for control and further analyses. The wet sample (> 2 mm) and the wetted drum are weighted (A (wet)) for further testing.

The drum containing the sample is put in the slaking container with tap water at 20–25 °C, and the drum is rotated at 20 rpm for 10 min. The drum plus the retained portion of the sample is removed from the container and weighted (C_i (wet)) before a draining phase in a drying cabinet at 30 °C for 24 h. The procedure is repeated i times, meaning i cycles of wetting, weighting, and draining. After the last cycle, in this case after 4 cycles, the sample is dried in the oven at 50 °C to a constant weight. The dry weight of the drum plus the retained portion of the sample is recorded (C_i). Table 2 summarize the notations used for the weight records used in the calculations.

The calculation of the modified slake durability index (MSDI) is based on the dry weights of the sample prior to the first cycle and after a complete test cycle. The slaking trend during the cycles can be obtained by calculating the slake trend index (STI) after each cycle; however, the weight records include water to an unknown amount. Three different parameters are possible for evaluations of the wetting effect:

Wetting index, I_wetting, which describes the material loss < 2 mm during static wetting for 72 h of the sample. The index is calculated based on the dry weight of the material passing through the drum after wetting subtracted from the initial dry weight of the sample (C_wetting).

Slaking trend index, STI_i (wet), which describe the evolution of material loss < 2 mm during repetitive cycles of wetting and draining. The index is calculated based on the wet weight of the retained material of cycle i compared with the initial wet weight of the sample after wetting. Since the amount of water in the samples is unknown, the trendline numbers do not reflect the exact material loss.

Modified slake durability index, MSDI_i, which describe the material loss < 2 mm after i cycles of wetting and draining, whereby the initial state of the samples is saturated. The index is calculated based on the dry weight of the retained material after the last cycle (C_i) compared with the initial dry weight of the sample after wetting (A′). The index is only to be calculated after a complete test procedure of i cycles. The index can be compared with the ISRM slake durability index (SDI_i) when the number of slaking cycles is similar.

By computing the slake trend index (STI_i) after each cycle, one can evaluate the evolution of slaking during the test. The slake trend index after first cycle will indicate the weakening effect of the static wetting phase prior to the mechanical exposure in the rotating drum. The complete trendline during i cycles can further be compared with the trendline of the ISRM test so that any behavior change related to the different initial moisture state of the samples is detected. It should be noted that the slake trend index is calculated by comparing wet weights of the sample prior to and after the cycles, while the modified slake durability index (MSDI_i) is calculated based on the dry weights. The slake trend index after the i-th cycle is therefore not directly comparable with the modified slake durability index due to the water content.

To enable an assessment of eventual differences in the degree of disintegration in the performed slake durability tests, a particle size distribution analysis is performed on the samples after the completion of the test procedures. The analysis is performed by sieving both the retained material in the drum (> 2 mm) and the material left in the slaking container (< 2 mm). Sieves with quadratic mesh openings spanning from 62 to 0.063 mm are used, and a cumulative weight % analysis is performed on all samples in both slake durability tests. The particle size analysis enables further assessments on the extent of disintegration of the rock material after the complete slake durability test cycles when this is desired. Similar approaches of disintegration analysis have also been carried out by authors such as Erguler and Shakoor (2009), Gautam and Shakoor (2013), Heidari et al. (2015), and others.

The mineralogical composition of the all samples prior to slake durability tests is determined. In addition, the composition of the dissolved and disintegrated material < 2 mm during wetting in the modified test is also assessed for the samples where the material loss is higher than 0.5% (samples Flysch 7–11). Only minerals presenting > 2% in at least one sample is accounted for, and the values are rounded up to nearest %.

The main constituents of the flysch samples are quartz, chlorite, calcite, plagioclase, and mica, with smaller amounts of k-feldspar. The composition is varying between the different samples, where high amounts of quartz and plagioclase are related to lower amounts of mica, chlorite and amorphous phases, and vice versa. The deviation between crystalline and amorphous phases is semi-quantitative. The results are given in Table 3.

The mineral constituents of the serpentinite samples were difficult to assess by the XRD analysis, due to highly amorphous diffraction patterns. This means that the original crystal structures are broken which indicate extensive weathering of the rock material. As a very high percentage of the mineral structures are destroyed, the quantification of even the crystalline phases is approximate (Tijhuis 2018). Based on the experience of the analyst at NTNU, the main crystalline constituents are recognized as chrysotile, lizardite, kaolinite, and nepouite, with smaller amounts of pyrope, brucite, calcite, dolomite, and magnetite. In addition, sample Serp 6 contains enstatite and fosterite. The chrysotile and lizardite diffraction patterns are overlapping and not distinguished. The only sample where swelling clay is detected is sample Serp 5, with an unknown amount of corrensite. Due to a high degree of weathering/crystal destructions of the samples, the quantification of both crystalline and amorphous phases is approximate. The results are given in Table 3.

The composition of the dissolved and disintegrated material (< 2 mm) sieved after the wetting phase of the modified slake durability test is assessed. Only the samples Flysch 7–11 have a material loss exceeding 0.5%. The main constituents of the material are chlorite, mica, and quartz, where the content of chlorite and mica is slightly higher compared with the sample composition prior to wetting. The results are given in Table 4.

The slake trend index (SDI_i) of the ISRM suggested method is calculated after each cycle; whereby, the final calculation of the slake durability index is performed after an additional phase of drying. The results are given in Table 5.

The slaking evolution during the test is plotted based on the slake durability indices after each cycle, shown in Fig. 4a (flysch samples) and b (serpentinite samples).

The dissolved and disintegrated material < 2 mm left in the water after the static wetting phase was dried and weighted in order to calculate the material loss. Based on the material loss, the dry weight of the samples after wetting is calculated, and the wetting index (I_wetting) is determined. Visual descriptions of the samples are also recorded. The results are given in Table 6.

The samples Flysch 7, Flysch 9, and Flysch 10 show the highest material loss (< 2 mm) during wetting, while Flysch 6 and the serpentinite samples show minor weight loss. However, the visual assessment reveals appreciable disintegration and changes in the samples Flysch 8–11, some changes of Flysch 7 and Serp 7, and little or no changes in Flysch 6, Serp 5, Serp 6, and Serp 8. The visual changes during wetting are exemplified in Fig. 5, by the photos of Flysch 11 and Serp 7.

After the wetting phase, the samples underwent the modified slake durability test. The results include all the durability indices obtained from the testing procedure, whereby the modified slake durability index (MSDI) is the parameter describing the slaking potential based on the dry weight loss of the samples during cyclic wetting and draining (Table 7). It is reminded that the STI and MSDI are calculated based on two different moisture states of the samples, explaining why the MSDI₄ show slightly higher values compared with the STI₄ for some of the samples.

Based on the slake trend indices calculated after each cycle (wet state), the slaking evolution can be assessed (Figs. 6 and 7)

After the last cycle, each sample is sieved in aiming to analyze the actual disintegration. Particle size distribution curves are obtained by plotting the cumulative weight of each fraction of the sample passing the respective sieves, with mesh openings spanning from 62 to 0.063 mm. The results are illustrated in Fig. 8 a (flysch samples) and b (serpentinite samples).

A detailed assessment on loss of durability due to initial wetting is performed by comparing the slake durability indices, where the initial state before the tests is dry (SDI of the ISRM test) and wet (MSDI of the modified test). Abundant differences in slaking behavior are observed during the first cycle of the two test procedures, illustrated in Fig. 9. It should be noted that the slake durability indices obtained after the first cycle may not be directly comparable due to different moisture content, still, the obtained values demonstrates a tendency of relative disintegration. The samples Flysch 8–11 show extremely reduced resistance to the mechanical impact imposed by the rotation of the drum, while the other samples show minor deviating results when comparing the two test methodologies. This indicate that the samples have different material properties and vulnerability to changes in moisture content in terms of water-weakening effects due to saturation.

The slake durability indices after 4 cycles, calculated based on dry weights, can be compared directly (Fig. 10). The samples Flysch 8–11 show the lowest durability in both test procedures, while Flysch 6–7 and the serpentinite samples show relatively high durability. The water-weakening effect of the initial wetting on repeated slaking cycles is prominent in Flysch 9–11 and virtually absent in Flysch 6–7 and the serpentinite samples. A comparison of the slake durability indices of the ISRM method and the modified method is shown in Fig. 10.

Although the slake durability index is an indicative material parameter on disintegration, it may fail to detect the disintegration behavior of rock materials where at least one diameter of the disintegrated particles exceeds 2 mm. Even at high slake durability indices, major size and mass reductions of the lumps can be the case. A comparison of the slake durability index and the cumulative weights of particle sizes > 2 mm capture this feature. Table 8 show a comparison the slake durability indices and weight % of particles < 16 mm and < 4 mm after the tests.

A fair correspondence between slake durability indices and disintegration require a low weight % of fractions less than the initial diameter of the samples (~ 40 mm) for high slake durability index values. For the samples Flysch 6 and Flysch 7, both the slake durability indices correspond fairly to the weight % of material less than 16 mm and 4 mm, meaning that the low actual disintegration is the reflection on the high slake durability index.

In the case of sample Flysch 8, the slake durability indices are SDI₄ = 70.8 and MSDI₄ = 73.4, i.e., medium slaking. However, the disintegration is quite extensive compared with the slake durability index, with 32.8–33.8 % of the grains being less than 16 mm and 26.5–30.1 % of the grain less than 4 mm in the modified test and ISRM test, respectively.

For the samples Flysch 9–11, the slake durability indices indicate low durability (< 60). However, based on the weight % of the particles passing through the 16 mm and 4 mm sieves, the slake durability indices are relatively high compared with the actual disintegration of the rock material. Flysch 11 show the most extensive disintegration whereby most of the particles of the retained material pass the 16 mm sieve (83.0% in the ISRM-test-and 97.5% in the modified test) and the 4 mm sieve (67.5 % in the ISRM test and 85.6 % in the modified test). In addition, the grains are splintered, a factor contributing to misleading results even after the grain size analyses due to the quadratic openings of the sieves (Fig. 11).

The limited correspondence between the slake durability index and actual disintegration is obvious for some of the samples and may cause underestimated disintegration potentials. For example, the serpentinite samples and Flysch 7 achieve similar slaking indices, but the disintegration behavior is considerably different when the material is assessed by visual inspection. The deviating disintegration behavior despite quite similar slake durability indices is illustrated in Fig. 12.

The sensitive components (i.e., the clay/clay-like minerals) and the slake durability indices of all samples were calculated and compared (Fig. 13) in order to detect eventual patterns in rock material composition and water-weakening effects. A general trend is that an increasing degree of weathering, indicated by high estimates of clay and clay-like mineral content (left axis), result in a lower slake durabilities (right axis). The lower slake durability indices in the modified test is pronounced in the flysch samples where the clay content exceeds 20% (samples Flysch 9–11).

A similar analysis was performed with respect to the actual disintegration, whereby the cumulative weight of particles passing through the 16-mm sieve is used to exemplify this trend (Fig. 14). An increasing content of clay and clay-like minerals correlates with increased disintegration and larger span between the ISRM test results and modified test results.

The ISRM slake durability test is useful as a general comparison of the slaking properties of different rock types. In terms of support design of a tunnel, however, it is crucial to obtain material parameters based on assessment obtained as close to the environmental conditions of the actual project as possible. As Franklin and Chandra already mentioned in 1972, other mechanisms than simple drying and wetting may have considerable effect on the deterioration of geologically weathered rocks if the environment is particularly severe.

In general, rock mass classification systems for engineering purposes combine findings from observation, experience and engineering judgment to provide a quantitative assessment of rock mass quality (Williams 1997). These can be used either to simply characterize rock properties and thereby facilitate the application of information into a design or relate findings to the determination of actual design parameters. For a classification system to be successful, the parameters must be relevant to their application, especially if the findings are to be related to the determination of actual design parameters.

The rock mass surrounding an underground opening will, dependent on the construction method, be disturbed and degraded already during the construction phase of the project. In terms of stability assessments of a tunnel traversing a heterogeneous and disturbed rock mass, the behavioral characterization of the material at a defined location is considered as more helpful than general parameters of a specific rock type. Further, eventual changed behavior resulting from the exposure to degrading agents such as water in water tunnels during operation is crucial information for the support design analysis.

The duration of 10 min in the slake durability test exposes the rock samples to a limited wetting phase, where the saturation degree of the lumps is variable and uncertain. As a result, only an unknown % of the rock material is saturated and exposed to the slaking effect. The modified slake durability index (MSDI) test aims to bridge this gap and to specify the environmental effects on the slaking properties of rocks in water tunnels for hydropower projects, without significantly reducing the simplicity and comparability of the established ISRM procedure. Firstly, the slaking properties of the material constituting a defined location are assessed rather than the properties of a single rock type. This enable an evaluation of heterogeneous and disturbed rock mass where the material properties may change within very short distances. Secondly, by introducing the samples to an extensive wetting phase prior to the test, the slaking effect of moisture changes is assessed closer to the in-situ condition of water tunnels. Thirdly, the rock material is not exposed to artificially high temperatures or dehydration states during the test, which potentially can change the material behavior. In addition, the method allows a separation between the effect of static wetting and mechanical abrasion, which opens up a possibility for an early assessment of the moisture sensitivity of the tested material.

Three slake durability parameters are obtained in the modified test; the wetting index (I_wetting), the slake trend index (STI_i), and the modified slake durability index (MSDI_i).

The wetting index in combination with visual characterization intend to indicate the resistance of the material to dissolution and disintegration due to static wetting and may function as a first-hand determination on the moisture sensitivity of the rock material. By visually comparing the lumps before and after the wetting phase, one can qualitatively assess the rock material (Fig. 5). By comparing the color of the water, eventual structural changes and disintegration of the lumps, a first prediction of the water sensitivity can be made already at this stage. By examining the dissolved and disintegrated material by XRD, one can also indicate which components of the material are more sensitive to the water exposure. Based on the calculation procedure of the slake durability index generalized in both the ISRM procedure and the modified procedure, the wetting index is computed from the weight of retained material after sieving the material passed through 2-mm mesh of the drum. As shown in Table 6, the wetting index is very high for all samples. However, some of the lumps disintegrates heavily during wetting into rock pieces > 2 mm, such as sample Flysch 11 (Fig. 11). Similar as for the slake durability index, the variation between the samples in regard of the actual disintegration behavior during wetting is not reflected in the weight records, since the calculations are based on the weight of particles less and larger than 2 mm only. This weakness is connected to the calculation procedure rather than the test procedure itself and can be solved by descriptions and/or photographs of the retained material. A first-hand determination on the water-weakening effect can therefore be made at this stage, but the wetting index should be evaluated together with visual observations of the material. If the samples show heavy disintegration due to the static wetting phase, an analysis procedure and classification system as suggested by authors describing static slaking tests can be chosen, and the test can be closed already at this stage.

The slake trend index intends to produce values to evaluate the evolution of slaking during repeated cycles of changed moisture conditions. This enables an evaluation of the water-weakening effect on the samples when they are introduced to minor mechanical forces, and an assessment of the slaking progress due to repeated cycles. The slake trend indices in the modified test are calculated when the samples are partly saturated by water and cannot be compared with the slake trend indices of the ISRM procedure directly. However, the trends may be compared in order to uncover eventual changes in slaking behavior due to the initial moisture state. In cases where the STI is low after one or few cycles, the test can easily be closed by drying the retained material and calculate the slake durability index. This is recommended in cases where time saving is crucial and where the durability is obviously lower than a specified support design limit.

The modified slake durability index intends to quantify the slake durability of samples exposed to an extensive wetting phase prior to cycles of changed moisture content under stable temperatures. The index is calculated after drying the retained material at 50 °C until no more weight loss and is therefore also comparable with the ISRM slake durability index. The index and its precedent procedure are recommended in cases where abundant water exposure is natural in terms of project type, as in hydropower.

In order to assess eventual differences in slaking behavior of saturated rocks compared with dry rocks, the modified test has the same framework and follows similar standardized steps as the ISRM suggested method, and both procedures are performed on similar samples. This enable a comparison of the slake durability indices, whereby the main deviating test conditions are the initial moisture state of the samples and the temperature exerted on the rock material during the test.

The wetting phase in the modified test revealed a significantly lowered slake durability of some samples compared with the ISRM test, which is very useful information for the water tunnels. The effect is varying between the samples tested, where the heterogeneous flysch samples are extensively affected compared with the homogeneous samples. The homogeneous samples did not show noteworthy different slaking behavior in the two test procedures. This deviation seems to be somehow connected to an increasing content of clay minerals, which may again be linked to the initial degree of weathering. Other factors may also contribute, as fabric, structure, strength, and initial micro-fracturing of the material. The samples in which the water sensitivity is revealed during passive wetting, are similar samples which show a lowered slake durability in the modified test. The lowered durability due to initial saturation is most prominent in the first cycle of the test, when minor mechanical forces are introduced due to collision of the lumps (Fig. 9). This water-weakening effect is apparently connected to the structure and composition of the samples, and most likely also to the dry strength of the rock material. To verify this, analyses such as strength tests, microscopy, and SEM-analyses are recommended for further research.

As some rocks are more sensitive to moisture changes than others, the modified test is assumed to reflect the degradation potential more efficiently than a test carried out on dehydrated samples as suggested by ISRM (1979). With the proposed modified test, the boundary conditions are closer to the in situ environment of the rock close to the periphery of a water tunnel, which in turn produce more reliable estimates on the behavior to be expected. It is possible to close the test after fewer cycles than of this research, if the samples show an extensive slaking behavior exceeding the support design limit. In order to obtain an index value on moisture sensitivity and slaking behavior, the modified test seems to uncover these features more efficiently than the ISRM suggested method.

The practical value of a database with slake durability results of different rock types is significantly reduced if no other disintegration parameters are obtained. The weight % of material fractions spanning from > 2 mm up to the initial lump diameters can be used to assess the linkage between the calculated slake durability indices and actual disintegration of the retained material. Such analyses enable further disintegration parameters to be evaluated if found necessary, based on the purpose of the durability assessment. For example, the retained fragments may be categorized by a disintegration ratio (D_R) analysis as suggested by Erguler and Shakoor (2009) or other similar categorization systems. For a complete overview of the disintegration behavior, the material passing the 2-mm mesh of the drum can be included in the disintegration analysis.

As performed in this research, a particle size distribution analysis uncovers noticeable differences between the disintegration behavior of the rock types tested compared with the slake durability indices obtained. The materials which disintegrates the most (Fig. 8a, b) are also the samples that show degradation at the wetting stage of the modified test (Table 6). These samples disintegrate more when exposed to the modified slake durability test procedure compared with the ISRM procedure, which may be connected to the content of clay (Fig. 14). The methodology of integrating the disintegration analysis into the slake durability assessment should be adjusted to the purpose of the analysis, as support design or similar motives.