nach oben

Tribology Letters

Erschienen in:

01.09.2021 | Original Paper

Dry-Sliding Wear Mechanisms of Shot-Peened Additive Manufactured Alpha Titanium Featuring TiB Particles

verfasst von: Liza-Anastasia DiCecco, Mehdi Mehdi, Afsaneh Edrisy

Erschienen in: Tribology Letters | Ausgabe 3/2021

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

The load-induced dry-sliding wear behavior of alpha titanium (Ti) with low amount of boron (< 1 wt%) samples made through plasma transferred arc solid free form fabrication process were studied in the untreated and hardened shot-peened surface conditions. Shot peening conducted at 90 psi for two minutes for 100% coverage with S-550 steel shots, was found to lead to an increase in surface hardness, with a depth of penetration of approximately 1 mm. While shot peening in this scheme was found to have a limited influence on COF and wear rates, it did influence the wear mechanisms observed. Untreated samples had a shift in wear behavior from low to high loading conditions. Dominating wear mechanisms at low loads (≤ 10 N) for untreated samples were oxidative and abrasive wear accompanied by weight gain of the steel counterface balls. At higher loads (> 10 N), untreated samples experienced weight loss of the steel counterface balls and severe plastic deformation with the formation and onset delamination of mechanically mixed layers (MML). Comparatively, shot-peened samples exhibited limited changes in wear behavior, remaining dominated by oxidation wear over the loading range. With oxidation wear dominating and the shot peening treatment inhibiting the formation of a MML and its delamination, it is hypothesized that the transition to severe wear may be delayed to higher loads from this treatment.

Vorheriger Artikel A Sticky Situation or Rough Going? Influencing Haptic Perception of Wood Coatings Through Frictional and Topographical Design

Nächster Artikel Soft EHL-Based Friction Mechanism of Unreinforced and GF-Reinforced PA66 in Contact with Steel Under PAO8 Oil Lubrication

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Nur mit Berechtigung zugänglich

Niinomi, M.: Mechanical properties of biomedical titanium alloys. Mater. Sci. Eng. A 243, 231–236 (1998). https://doi.org/10.1016/S0921-5093(97)00806-XCrossRef

Donachie, M.J.J.: A primer on titanium and its alloys. In: Titanium - A technical guide. pp. 1–3. ASM International, Materials Park (2000)

Lütjering, G., Williams, J.C.: Titanium : engineering materials and processes. Springer, New York (2007)

Niknam, S.A., Khettabi, R., Songmene, V.: Machinability and machining of titanium alloys: a review. In: Davim, J.P. (ed.) Machining of titanium alloys, pp. 1–10. Springer-Verlag, Berlin Heidelberg, New York (2014)

Arrazola, P.J., Garay, A., Iriarte, L.M., Armendia, M., Marya, S., Le Maître, F.: Machinability of titanium alloys (Ti6Al4V and Ti555.3). J. Mater. Process. Technol. 209, 2223–2230 (2009). https://doi.org/10.1016/j.jmatprotec.2008.06.020CrossRef

Budinski, K.G.: Tribological properties of titanium alloys. Wear 151, 203–217 (1991). https://doi.org/10.1016/0043-1648(91)90249-TCrossRef

Molinari, A., Straffelini, G., Tesi, B., Bacci, T.: Dry sliding wear mechanisms of the Ti6Al4V alloy. Wear 208, 105–112 (1997). https://doi.org/10.1016/S0043-1648(96)07454-6CrossRef

Yerramareddy, S., Bahadur, S.: The effect of laser surface treatments on the tribological behavior of Ti-6Al-4V. Wear 157, 245–262 (1992). https://doi.org/10.1016/0043-1648(92)90065-GCrossRef

Farokhzadeh, K., Edrisy, A.: Transition between mild and severe wear in titanium alloys. Tribol. Int. 94, 98–111 (2016). https://doi.org/10.1016/j.triboint.2015.08.020CrossRef

10.

Leverant, G.R., Langer, B.S., Yuen, A., Hopkins, S.W.: Surface residual stresses, surface topography and the fatigue behavior of Ti-6AI-4V. Metall. Trans. A 10, 251–257 (1979). https://doi.org/10.1007/BF02817635CrossRef

11.

Starker, P., Wohlfahrt, H., Macherauch, E.: Subsurface crack initiation during fatigue as a result of residual stresses. Fatigue Fract. Eng. Mater. Struct. 1, 319–327 (1979). https://doi.org/10.1111/j.1460-2695.1979.tb00388.xCrossRef

12.

Wagner, L., Luetjeringe, G.: Influence of shot peening on the fatigue behavior of titanium alloys. In: International Conference on Shot Peening - 1. pp. 453–460. International Scientific Committee for Shot Peening (1981)

13.

Petit-Renaud, F.: Optimization of the shot peening parameters. In: Wagner, L. (ed.) Shot Peening - Proceedings of the 8th International Conference on Shot Peening. Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim (2003)

14.

Ganesh, B.K.C., Ramanaih, N., Chandrasekhar Rao, P.V.: Dry sliding wear behavior of Ti – 6Al – 4V implant alloy subjected to various surface treatments. Trans. Indian Inst. Met. 65, 425–434 (2012). https://doi.org/10.1007/s12666-012-0147-4CrossRef

15.

Ganesh, B.K.C., Sha, W., Ramanaiah, N., Krishnaiah, A.: Effect of shotpeening on sliding wear and tensile behavior of titanium implant alloys. J. Mater. Des. 56, 480–486 (2014). https://doi.org/10.1016/j.matdes.2013.11.052CrossRef

16.

Unal, O., Karaoglanli, A.C., Ozgurluk, Y., Doleker, K.M., Maleki, E., Varol, R.: Wear behavior of severe shot peened and thermally oxidized commercially pure titanium. In: Advanced structured materials, pp. 461–470. Springer International Publishing, New York (2019)

17.

Morsi, K., Patel, V.V.: Processing and properties of titanium – titanium boride (TiBw) matrix composites — a review. J. Mater. Sci. 42, 2037–2047 (2007). https://doi.org/10.1007/s10853-006-0776-2CrossRef

18.

He, P., Yang, M., Lin, T., Jiao, Z.: Improving the strength of brazed joints with in situ synthesized TiB whiskers. J. Alloys Compd. 509, L289–L292 (2011). https://doi.org/10.1016/j.jallcom.2011.05.026CrossRef

19.

Cai, C., Song, B., Qiu, C., Li, L., Xue, P., Wei, Q., Zhou, J., Nan, H., Chen, H., Shi, Y.: Hot isostatic pressing of in-situ TiB/Ti-6Al-4V composites with novel reinforcement architecture, enhanced hardness and elevated tribological properties. J. Alloys Compd. 710, 364–374 (2017). https://doi.org/10.1016/j.jallcom.2017.03.160CrossRef

20.

Ma, F., Liu, P., Li, W., Liu, X., Chen, X., Zhang, K., Pan, D., Lu, W.: The mechanical behavior dependence on the TiB whisker realignment during hot-working in titanium matrix composites. Sci. Rep. 6, 1–9 (2016). https://doi.org/10.1038/srep36126CrossRef

21.

Pouzet, S., Peyre, P., Gorny, C., Castelnau, O., Baudin, T., Brisset, F., Colin, C., Gadaud, P.: Additive layer manufacturing of titanium matrix composites using the direct metal deposition laser process. Mater. Sci. Eng. A 677, 171–181 (2016). https://doi.org/10.1016/j.msea.2016.09.002CrossRef

22.

Miklaszewski, A.: Ultrafast densification and microstructure evolution of in situ Ti/TiB metal matrix composite obtained by PPS approach. Int. J. Refract. Met. Hard Mater. 65, 34–38 (2017). https://doi.org/10.1016/j.ijrmhm.2016.10.007CrossRef

23.

Popoola, A.P.I., Phume, L., Pityana, S., Aigbodion, V.S.: In-situ formation of laser Ti6Al4V-TiB composite coatings on Ti6Al4V alloy for biomedical application. Surf. Coatings Technol. 285, 161–170 (2016). https://doi.org/10.1016/j.surfcoat.2015.10.079CrossRef

24.

Li, S., Kondoh, K., Imai, H., Chen, B., Jia, L., Umeda, J.: Microstructure and mechanical properties of P/M titanium matrix composites reinforced by in-situ synthesized TiC-TiB. Mater. Sci. Eng. A 628, 75–83 (2015). https://doi.org/10.1016/j.msea.2015.01.033CrossRef

25.

Weng, F., Yu, H., Chen, C., Liu, J., Zhao, L., Dai, J., Zhao, Z.: Effect of process parameters on the microstructure evolution and wear property of the laser cladding coatings on Ti-6Al-4V alloy. J. Alloys Compd. 692, 989–996 (2017). https://doi.org/10.1016/j.jallcom.2016.09.071CrossRef

26.

Dutta, B., Froes, F.H.: The additive manufacturing (AM) of titanium alloys. Met. Powder Rep. 72, 96–106 (2017). https://doi.org/10.1016/j.mprp.2016.12.062CrossRef

27.

Kooi, B.J., Pei, Y.T., De Hosson, J.T.M.: The evolution of microstructure in a laser clad TiB-Ti composite coating. Acta Mater. 51, 831–845 (2003). https://doi.org/10.1016/S1359-6454(02)00475-5CrossRef

28.

Banerjee, R., Collins, P.C., Fraser, H.L.: Laser deposition of in situ Ti – TiB composites. Adv. Eng. Mater. 4, 847–851 (2002). https://doi.org/10.1002/1527-2648(20021105)4:11%3c847::AID-ADEM847%3e3.0.CO;2-CCrossRef

29.

Nag, S., Banerjee, R.: Volume 23: fundamentals of medical implant materials - materials for medical devices. In: ASM handbook. pp. 6–17. ASM International, Materials Park (2012)

30.

Hu, Y., Ning, F., Wang, H., Cong, W., Zhao, B.: Laser engineered net shaping of quasi-continuous network microstructural TiB reinforced titanium matrix bulk composites: microstructure and wear performance. Opt. Laser Technol. 99, 174–183 (2018). https://doi.org/10.1016/j.optlastec.2017.08.032CrossRef

31.

Sabahi Namini, A., Dilawary, S.A.A., Motallebzadeh, A., Shahedi Asl, M.: Effect of TiB2 addition on the elevated temperature tribological behavior of spark plasma sintered Ti matrix composite. Compos. Part B Eng. 172, 271–280 (2019). https://doi.org/10.1016/j.compositesb.2019.05.073CrossRef

32.

Boudreau, D., DiCecco, L., Gali, O., Edrisy, A.: Fatigue behaviour of additive manufactured Ti-TiB. MRS Adv. 3, 3641–3653 (2018). https://doi.org/10.1557/adv.2018.618CrossRef

33.

Attar, H., Bönisch, M., Calin, M., Zhang, L.C., Scudino, S., Eckert, J.: Selective laser melting of in situ titanium-titanium boride composites: processing, microstructure and mechanical properties. Acta Mater. 76, 13–22 (2014). https://doi.org/10.1016/j.actamat.2014.05.022CrossRef

34.

Farokhzadeh, K., Qian, J., Edrisy, A.: Effect of SPD surface layer on plasma nitriding of Ti–6Al–4V alloy. Mater. Sci. Eng. A 589, 199–208 (2014). https://doi.org/10.1016/j.msea.2013.09.077CrossRef

35.

Partridge, P.G.: The crystallography and deformation modes of hexagonal close-packed metals. Metall. Rev. 12, 169–194 (1967). https://doi.org/10.1179/mtlr.1967.12.1.169CrossRef

36.

Yoo, M.H., Lee, J.K.: Deformation twinning in Hcp metals and alloys. Philos. Mag. A 63, 987–1000 (1991). https://doi.org/10.1080/01418619108213931CrossRef

37.

Kumar, M.A., Capolungo, L., Mccabe, R.J., Tomé, C.N.: Characterizing the role of adjoining twins at grain boundaries in hexagonal close packed materials. Sci. Rep. 9, 1–10 (2019). https://doi.org/10.1038/s41598-019-40615-5CrossRef

38.

Nervo, L., King, A., Fitzner, A., Ludwig, W., Preuss, M.: Acta Materialia A study of deformation twinning in a titanium alloy by X-ray diffraction contrast tomography. Acta Mater. 105, 417–428 (2016). https://doi.org/10.1016/j.actamat.2015.12.032CrossRef

39.

Bozzolo, N., Chan, L., Rollett, A.D.: Misorientations induced by deformation twinning in titanium research papers. J. Appl. Crystallogr. 43, 596–602 (2010). https://doi.org/10.1107/S0021889810008228CrossRef

40.

Bonnet, R., Cousineau, R., Warrington, D.H.: Determination of near-coincident cells for hexagonal crystals. Related DSC lattices. Acta Crystallogr. Sect. A 37, 184–189 (1981). https://doi.org/10.1107/S0567739481000466CrossRef

41.

Song, S.G., Gray, G.T., III.: Structural interpretation of the nucleation and growth of deformation twins in Zr and Ti—I. Application of the coincidence site lattice (CSL) theory to twinning problems in hcp structures. Acta Metall. Mater. 43, 2339–2350 (1995). https://doi.org/10.1016/0956-7151(94)00433-1CrossRef

42.

Jin, X., Lan, L., Gao, S., He, B., Rong, Y.: Effects of laser shock peening on microstructure and fatigue behavior of Ti–6Al–4V alloy fabricated via electron beam melting. Mater. Sci. Eng. A (2020). https://doi.org/10.1016/j.msea.2020.139199CrossRef

43.

Zhao, X., Zhou, H., Liu, Y.: Effect of shot peening on the fatigue properties of nickel-based superalloy GH4169 at high temperature. Results Phys. 11, 452–460 (2018). https://doi.org/10.1016/j.rinp.2018.09.047CrossRef

44.

Fitzner, A., Palmer, J., Gardner, B., Thomas, M., Preuss, M., da Fonseca, J.Q.: On the work hardening of titanium: new insights from nanoindentation. J. Mater. Sci. 54, 7961–7974 (2019). https://doi.org/10.1007/s10853-019-03431-wCrossRef

45.

Zhang, J., Alpas, A.T.: Delamination wear in ductile materials containing second phase particles. Mater. Sci. Eng. (1993). https://doi.org/10.1016/0921-5093(93)90494-YCrossRef

46.

Srivatsan, T.S., Soboyejo, W.O., Lederich, R.J.: Tensile deformation of a titanium-alloy and fracture behaviour composite. Compos. Part A (1997). https://doi.org/10.1016/S1359-835X(96)00136-4CrossRef

Titel: Dry-Sliding Wear Mechanisms of Shot-Peened Additive Manufactured Alpha Titanium Featuring TiB Particles
verfasst von: Liza-Anastasia DiCecco
Mehdi Mehdi
Afsaneh Edrisy
Publikationsdatum: 01.09.2021
Verlag: Springer US
Erschienen in: Tribology Letters / Ausgabe 3/2021
Print ISSN: 1023-8883
Elektronische ISSN: 1573-2711
DOI: https://doi.org/10.1007/s11249-021-01456-4

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 3/2021

Controlling the Friction of Gels by Regulating Interfacial Oxygen During Polymerization

Durability Improvement of Concentrated Polymer Brushes by Multiscale Texturing

Tribological Properties of SiO2@Cu and SiO2@MoS2 Core–Shell Microspheres as Lubricant Additives

Understanding Test Modalities of Tire Grip and Laboratory-Road Correlations with Modeling

Short Chain Imidazolium Ionic Liquids: Synthesis and Oil Miscibility in Various Base Oil by use of Surfactant as High Performance Friction and Antiwear Lubricant Additive

QCM Study of Tribotronic Control in Ionic Liquids and Nanoparticle Suspensions

Premium Partner

Marktübersichten