nach oben

Journal of Materials Engineering and Performance

Erschienen in:

17.04.2019

Effect of Tempering Temperature on the Precipitation Behavior and Mechanical Properties of a Martensite Ferritic Steel

verfasst von: Yulin Ma, Yue Liu, Junjia Zhang, Xu Jiang, Chunming Liu

Erschienen in: Journal of Materials Engineering and Performance | Ausgabe 5/2019

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

In this investigation, the precipitation of boron-containing M₂₃C₆ in the CB2 steel during tempering was investigated. Scanning electron microscopy, energy-dispersive x-ray spectroscopy, transmission electron microscopy and differential scanning calorimetry were used to analyze the influence of temperature on the microstructure and properties of CB2-tempered martensite ferritic steel. The steel was normalized at 1100 °C for 2 h and then tempered at six different temperatures between 690 and 790 °C for 2 h. During air-cooling following austenitization, the precipitation of M₃C particles occurred in flakes forming with their diameter and thickness of 100 and 20 nm, respectively. The boron-containing M₂₃C₆ was formed on the lath boundary after the dissolution of M₃C within the boundary. When the tempering temperature increased from 690 to 790 °C, the average diameter of boron-containing M₂₃C₆ increased from 132 to 198 nm. Owing to the rapid growth of the precipitates, the phenomenon of lath widening as well as the recovery of microstructure would take place at high temperature. With an increase in the temperature, the tensile and yield strengths decreased gradually, while the plasticity increased and the boron-containing M₂₃C₆ grew rapidly. Furthermore, when the tempering temperature exceeded 750 °C, the plasticity of CB2 steel was significantly improved.

Vorheriger Artikel Effects of Temperature and Heat Input on the Wear Mechanisms of Contact Tube for Non-copper-Coated Solid Wires

Nächster Artikel Effect of Tempering Mode on the Microstructure and Mechanical Properties of a Lean Alloy Martensitic Steel: Conventional Reheating Versus Induction Reheating

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

G. Gupta and G.S. Was, Improved Creep Behavior of Ferritic-Martensitic Alloy T91 by Subgrain Boundary Density Enhancement, Metall. Mater. Trans. A, 2008, 39a(1), p 150–164CrossRef

P. Yan, Z.D. Liu, H.S. Bao, Y.Q. Weng, and W. Liu, Effect of Normalizing Temperature on the Strength of 9Cr-3W-3Co Martensitic Heat Resistant Steel, Mater. Sci. Eng. A, 2014, 597, p 148–156CrossRef

F. Abe, Effect of Quenching, Tempering, and Cold Rolling on Creep Deformation Behavior of a Tempered Martensitic 9Cr-1W Steel, Metall. Mater. Trans. A, 2003, 34a(4), p 913–925CrossRef

J.R. Li, C.L. Zhang, B. Jiang, L.Y. Zhou, and Y.Z. Liu, Effect of Large-Size M23C6-Type Carbides on the Low-Temperature Toughness of Martensitic Heat-Resistant Steels, J. Alloys Compd., 2016, 685, p 248–257CrossRef

H.G. Armaki, R.P. Chen, K. Maruyama, and M. Igarashi, Creep Behavior and Degradation of Subgrain Structures Pinned by Nanoscale Precipitates in Strength-Enhanced 5 to 12 Pct Cr Ferritic Steels, Metall. Mater. Trans. A, 2011, 42a(10), p 3084–3094CrossRef

D. Kolesnikov, A. Belyakov, A. Kipelova, V. Dudko, R. Kaibyshev, D. Molodov, Zener Pinning Pressure in Tempered Martensite Lath Structure, Recryst. Grain Growth IV, 2012, 715-716, p 745–750.

Y.T. Xu, X.Y. Zhang, Y.B. Tian, C. Chen, Y.J. Nan, H. He, and M.J. Wang, Study on the Nucleation and Growth of M23C6 Carbides in a 10% Cr Martensite Ferritic Steel After Long-Term Aging, Mater. Charact., 2016, 111, p 122–127CrossRef

A. Kostka, K.G. Tak, R.J. Hellmig, Y. Estrin, and G. Eggeler, On the Contribution of Carbides and Micrograin Boundaries to the Creep Strength of Tempered Martensite Ferritic Steels, Acta Mater., 2007, 55(2), p 539–550CrossRef

M.I. Isik, A. Kostka, and G. Eggeler, On the Nucleation of Laves Phase Particles During High-Temperature Exposure and Creep of Tempered Martensite Ferritic Steels, Acta Mater., 2014, 81, p 230–240CrossRef

10.

M.I. Isik, A. Kostka, V.A. Yardley, K.G. Pradeep, M.J. Duarte, P.P. Choi, D. Raabe, and G. Eggeler, The Nucleation of Mo-Rich Laves Phase Particles Adjacent to M₂₃C₆ Micrograin Boundary Carbides in 12% Cr Tempered Martensite Ferritic Steels, Acta Mater., 2015, 90, p 94–104CrossRef

11.

A. Czyrska-Filemonowicz, A. Zielińska-Lipiec, and P. Ennis, Modified 9% Cr Steels for Advanced Power Generation: Microstructure and Properties, J. Achiev. Mater. Manuf. Eng., 2006, 19(2), p 43–48

12.

K. Maile, Evaluation of Microstructural Parameters in 9–12% Cr-Steels, Int. J. Press. Vessels Pip., 2007, 84(1), p 62–68CrossRef

13.

P. Hu, W. Yan, W. Sha, W. Wang, Y.Y. Shan, and K. Yang, Microstructure Evolution of a 10Cr Heat-Resistant Steel during High Temperature Creep, J. Mater. Sci. Technol., 2011, 27(4), p 344–351CrossRef

14.

E.J. Payton, A. Aghajani, F. Otto, G. Eggeler, and V.A. Yardley, On the Nature of Internal Interfaces in a Tempered Martensite Ferritic Steel and Their Evolution During Long-Term Creep, Scr. Mater., 2012, 66(12), p 1045–1048CrossRef

15.

A. Aghajani, C. Somsen, and G. Eggeler, On the Effect of Long-Term Creep on the Microstructure of a 12% Chromium Tempered Martensite Ferritic Steel, Acta Mater., 2009, 57(17), p 5093–5106CrossRef

16.

S. Baumgartner, M. Schuler, A. Holy, R. Schnitzer, and N. Enzinger, Dissimilar Welding of the Creep Resistant Steels CB2 and P92 with Flux Cored Wires, Weld World, 2015, 59(5), p 655–665CrossRef

17.

D. Jandova, J. Kasl, and E. Chvostova, Microstructure of CB2 Steel Before and After Long-Term Creep Tests, Metallography Xv, 2014, 782, p 311–318

18.

Y. Liu, Y. Ma, H. Guo, and C. Liu, Effects of Co and B on Microstructure and Properties of Modified Ferritic Heat-resistant Steels, Mater. Rev., 2015, 13, p 003

19.

R. Viswanathan, J. Shingledecker, J. Hawk, and S. Goodstine-Alstom, Effect of Creep in Advanced Materials for Use in Ultrasupercritical Coal Power Plants, Creep & Fracture in High Temperature Components: Design & Life Assessment Issues, Proceedings, 2009, p 31–43

20.

A. Vyrostkova, L. Falat, J. Kepic, P. Brziak, and J. Pecha, Microstructure and Fracture of 9%Cr-Mo-Co-B Steel (Cb2) Weldment After Isothermal Ageing, Metal 2010: 19th International Metallurgical and Materials Conference, 2010, p 409–414

21.

R. Vanstone, I. Chilton, and P. Jaworski, Manufacturing Experience in An Advanced 9%CrMoCoVNbNB Alloy for Ultra-Supercritical Steam Turbine Rotor Forgings and Castings, J. Eng. Gas Turb. Power, 2013, 135(6)

22.

M. Staubli, R. Hanus, T. Weber, K. Mayer, and T. Kern, The European Efforts in Development of New High Temperature Casing Materials–COST 536, Proceedings of the 8th Liège Conference, European Commission, Université de Liège (Part II), 2006, p 855–870

23.

Y.Z. Shen, S.H. Kim, C.H. Han, H.D. Cho, and W.S. Ryu, TEM Investigations of MN Nitride Phases in a 9% Chromium Ferritic/Martensitic Steel with Normalization Conditions for Nuclear Reactors, J. Nucl. Mater., 2009, 384(1), p 48–55CrossRef

24.

A. Schneider and G. Inden, Simulation of the Kinetics of Precipitation Reactions in Ferritic Steels, Acta Mater., 2005, 53(2), p 519–531CrossRef

25.

J. Kasl, S. Mikmekova, and D. Jandova, SEM, TEM and SLEEM (Scanning Low Energy Electron Microscopy) of CB2 Steel After Creep Testing, Iop Conf Ser-Mat Sci, 2014, 55

26.

L. Korcakova, J. Hald, and M.A.J. Somers, Quantification of Laves Phase Particle Size in 9CrW Steel, Mater. Charact., 2001, 47(2), p 111–117CrossRef

27.

P. Dou, A. Kimura, R. Kasada, T. Okuda, M. Inoue, S. Ukai, S. Ohnuki, T. Fujisawa, and F. Abe, TEM and HRTEM Study of Oxide Particles in An Al-Alloyed High-Cr Oxide Dispersion Strengthened Steel with Zr Addition, J. Nucl. Mater., 2014, 444(1–3), p 441–453CrossRef

28.

I. Fedorova, A. Kostka, E. Tkachev, A. Belyakov, and R. Kaibyshev, Tempering Behavior of a Low Nitrogen Boron-Added 9% Cr Steel, Mater. Sci. Eng. A, 2016, 662, p 443–455CrossRef

29.

G. Speich and W. Leslie, Tempering of steel, Metallurgical and Materials Transactions B, 1972, 3(5), p 1043–1054

30.

P. Chen and P. Winchell, Martensite Lattice Changes During Tempering, Metall. Mater. Trans. A, 1980, 11(8), p 1333–1339CrossRef

31.

A.Y. Kipelova, A.N. Belyakov, V.N. Skorobogatykh, I.A. Shchenkova, and R.O. Kaibyshev, Tempering-Induced Structural Changes in Steel 10Kh9K3V1M1FBR and Their Effect on the Mechanical Properties, Met. Sci. Heat Treat., 2010, 52(3–4), p 100–110CrossRef

32.

M. Hattestrand and H.O. Andren, Boron Distribution in 9–12% Chromium Steels, Mater. Sci. Eng. A, 1999, 270(1), p 33–37CrossRef

33.

A. Inoue and T. Masumoto, Carbide Reactions (M 3 C→ M 7 C 3→ M 23 C 6→ M 6 C) During Tempering of Rapidly Solidified High Carbon Cr–W and Cr–Mo Steels, Metall. Mater. Trans. A, 1980, 11(5), p 739–747CrossRef

34.

G. Olson and M. Cohen, Early Stages of Aging and Tempering of Ferrous Martensites, Metall. Trans. A, 1983, 14(5), p 1057–1065CrossRef

35.

H. Sieurin and R. Sandström, Sigma Phase Precipitation in Duplex Stainless Steel 2205, Mater. Sci. Eng. A, 2007, 444(1–2), p 271–276CrossRef

Titel: Effect of Tempering Temperature on the Precipitation Behavior and Mechanical Properties of a Martensite Ferritic Steel
verfasst von: Yulin Ma
Yue Liu
Junjia Zhang
Xu Jiang
Chunming Liu
Publikationsdatum: 17.04.2019
Verlag: Springer US
Erschienen in: Journal of Materials Engineering and Performance / Ausgabe 5/2019
Print ISSN: 1059-9495
Elektronische ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-019-03951-1

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 5/2019

Effect of Forging on Microstructure, Mechanical Properties and Acoustic Emission Characteristics of Al Alloy (2014): 10 wt.% SiCp Composite

Analysis of the Temperature Field in Al-Cu Dissimilar Materials Friction Stir Welding

On Mechanical Properties of New Railway Wheel Steels for Desert Environments and Sand Caused Wheel Damage Mechanisms

Fabrication, Microstructures, and Properties of 50 vol.% SiCp/6061Al Composites via Hot Pressing

Effects of Annealing on the Microstructures and Mechanical Properties of Cold-Rolled TB8 Alloy

Electrochemical Investigations on AZ Series Magnesium Alloys as Anode Materials in a Sodium Chloride Solution

Premium Partner

Marktübersichten