nach oben

The International Journal of Advanced Manufacturing Technology

Erschienen in:

27.05.2021 | ORIGINAL ARTICLE

Effects of CeO2 addition on microstructure and properties of ceramics reinforced Fe-based coatings by laser cladding

verfasst von: Liaoyuan Chen, Yu Zhao, Chuang Guan, Tianbiao Yu

Erschienen in: The International Journal of Advanced Manufacturing Technology | Ausgabe 7-8/2021

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

To reduce deposition defects (cracks and porosity) of the ceramics reinforced Fe-based coatings, and improve their microstructure uniformity, microhardness, and wear resistance, different content of CeO₂ (0, 1.0, 2.0, 2.5, and 3.0 wt.%) was added to the Fe-based powders. The effects of CeO₂ addition on the microstructure, phase composition, and mechanical properties were investigated by an optical microscope, X-ray diffraction (XRD), scanning electron microscopy (SEM), Vickers hardness tester, and friction wear tester. The results show that appropriate CeO₂ addition not only can reduce the cracks and porosities but also improve the bonding performance between the composite coating and the substrate. The study also finds that the addition of CeO₂ promotes the melting of large-size ceramic particles, increases the nucleation sites, and further refines the microstructure. The mechanical properties of each coating show that the microhardness and wear resistance firstly increases and then decreases with the increase of CeO₂ addition. The ceramics reinforced Fe-based coatings with 2.5 wt.% CeO₂ addition exhibites the highest and most uniform microhardness, and the smoothest worn surface despite the higher friction coefficient. Thus, CeO₂ addition is an effective method to refine the microstructure, reduce cracks and porosities in the TiN and Ti (C, N) reinforced Fe-based coating, and further improve microhardness and wear performance.

Vorheriger Artikel Deformation behavior during hot processing of the alloy of the Al-Mg system economically doped with scandium

Nächster Artikel Development of positioning error measurement system based on geometric optics for long linear stage

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Shamsaei N, Yadollahi A, Bian L, Thompson SM (2015) An overview of Direct Laser Deposition for additive manufacturing; Part II: Mechanical behavior, process parameter optimization and control. Addit Manuf 8:12–35. https://doi.org/10.1016/j.addma.2015.07.002CrossRef

Pi G, Zhang A, Zhu G, Li D, Lu B (2011) Research on the forming process of three-dimensional metal parts fabricated by laser direct metal forming. Int J Adv Manuf Technol 57:841–847. https://doi.org/10.1007/s00170-011-3404-5CrossRef

Ibrahim MZ, Sarhan AAD, Kuo TY, Yusuf F, Hamdi M, Chien CS (2018) Investigate the effects of the substrate surface roughness on the geometry, phase transformation, and hardness of laser-cladded Fe-based metallic glass coating. Int J Adv Manuf Technol 98:1977–1987. https://doi.org/10.1007/s00170-018-2354-6CrossRef

Song L, Zeng G, Xiao H, Xiao X, Li S (2016) Repair of 304 stainless steel by laser cladding with 316L stainless steel powders followed by laser surface alloying with WC powders. J Manuf Process 24:116–124CrossRef

Ozlati A, Movahedi M (2018) Effect of welding heat-input on tensile strength and fracture location in upset resistance weld of martensitic stainless steel to duplex stainless steel rods. J Manuf Process 35:517–525CrossRef

Liu H, Li M, Qin X, Huang S, Hong F Numerical simulation and experimental analysis of wide-beam laser cladding. Int J Adv Manuf Technol 100:237–249

Lo KH, Cheng FT, Kwok CT, Man HC (2003) Improvement of cavitation erosion resistance of AISI 316 stainless steel by laser surface alloying using fine WC powder. Surf Coat Technol 165:258–267CrossRef

Farahmand P, Kovacevic R (2015) Laser cladding assisted with an induction heater (LCAIH) of Ni-60%WC coating. J Mater Process Technol 222:244–258. https://doi.org/10.1016/j.jmatprotec.2015.02.026CrossRef

Guo C, Chen J, Zhou J, Zhao J, Wang L, Yu Y, Zhou H (2012) Effects of WC-Ni content on microstructure and wear resistance of laser cladding Ni-based alloys coating. Surf Coat Technol 206:2064–2071. https://doi.org/10.1016/j.surfcoat.2011.06.005CrossRef

10.

Qu J, Xiong W, Ye D, Yao Z, Liu W, Lin S (2010) Effect of WC content on the microstructure and mechanical properties of Ti(C0.5N0.5)-WC-Mo-Ni cermets. Int J Refract Met Hard Mater 28:243–249. https://doi.org/10.1016/j.ijrmhm.2009.10.005CrossRef

11.

Wu CL, Zhang S, Zhang CH, Zhang JB, Liu Y, Chen J (2019) Effects of SiC content on phase evolution and corrosion behavior of SiC-reinforced 316L stainless steel matrix composites by laser melting deposition. Opt Laser Technol 115:134–139. https://doi.org/10.1016/j.optlastec.2019.02.029CrossRef

12.

Liu S, Shin YC (2017) The influences of melting degree of TiC reinforcements on microstructure and mechanical properties of laser direct deposited Ti6Al4V-TiC composites. Mater Des 136:185–195. https://doi.org/10.1016/j.matdes.2017.09.063CrossRef

13.

Sun Q, Wang Z, Yang J, Liu Y, Liu J, Qiao Z, Liu W (2018) High-performance TiN reinforced Sialon matrix composites: A good combination of excellent toughness and tribological properties at a wide temperature range. Ceram Int 44:17258–17265CrossRef

14.

Yin J, Wang D, Meng L, Ke L, Hu Q, Zeng X (2017) High-temperature slide wear of Ni-Cr-Si metal silicide based composite coatings on copper substrate by laser-induction hybrid cladding. Surf Coat Technol 325:120–126CrossRef

15.

Yu T, Sun J, Qu W, Zhao Y, Yang L (2018) Influences of z-axis increment and analyses of defects of AISI 316L stainless steel hollow thin-walled cylinder. Int J Adv Manuf Technol 97:2203–2220CrossRef

16.

Zhang S, Lin X, Chen J, Huang W (2009) Heat-treated microstructure and mechanical properties of laser solid forming Ti-6Al-4V alloy. Rare Metals 28:537–544. https://doi.org/10.1007/s12598-009-0104-5CrossRef

17.

Yu T, Zhao Y, Sun J, Chen Y, Qu W (2018) Process parameters optimization and mechanical properties of forming parts by direct laser fabrication of YCF101 alloy. J Mater Process Technol 262:75–84CrossRef

18.

Casati R, Lemke J, Vedani M (2016) Microstructure and Fracture Behavior of 316L Austenitic Stainless Steel Produced by Selective Laser Melting. J Mater Sci Technol 32:738–744. https://doi.org/10.1016/j.jmst.2016.06.016CrossRef

19.

Zhao Y, Yu T, Li B, Wang Z, Chen H (2018) Calculation and verification of start/stop optimum overlapping rate on metal dlf technology. Int J Adv Manuf Technol 99:437–452. https://doi.org/10.1007/s00170-018-2445-4CrossRef

20.

Zhao Y, Yu T, Li B, Wang Z, Chen H (2018) Effect of laser cladding on forming qualities of YCF101 alloy powder in the different lap joint modes. Int J Adv Manuf Technol 96:1991–2001CrossRef

21.

Tao Z, Xun C, Shunxing W, Shian Z (2000) Effect of CeO2 on microstructure and corrosive wear behavior of laser-cladded Ni/WC coating. Thin Solid Films 379:128–132CrossRef

22.

Sharma SP, Dwivedi DK, Jain PK (2009) Effect of La2O3 addition on the microstructure, hardness and abrasive wear behavior of flame sprayed Ni based coatings. Wear 267:853–859CrossRef

23.

Li J, Yu ZS, Wang HP (2011) Effects of Y2O3 on Microstructure and Mechanical Properties of Laser Clad Coatings Reinforced by In Situ Synthesized TiB and TiC. Mater Sci Forum 675–677:589–592CrossRef

24.

Choi JO, Kim JY, Choi CO, Kim JK, Rohatgi PK (2004) Effect of rare earth element on microstructure formation and mechanical properties of thin wall ductile iron castings. Mater Sci Eng A 383:323–333CrossRef

25.

Hao F, Li D, Dan T, DAN T, REN X, LIAO (2011) Effect of rare earth oxides on the morphology of carbides in hardfacing metal of high chromium cast iron. J Rare Earths 29:168–172. https://doi.org/10.1016/S1002-0721(10)60425-5CrossRef

26.

Yu T, Yang L, Zhao Y, Sun J, Li B (2018) Experimental research and multi-response multi-parameter optimization of laser cladding Fe313. Opt Laser Technol 108:321–332. https://doi.org/10.1016/j.optlastec.2018.06.030CrossRef

27.

Yan H, Zhang P, Gao Q, Qin Y, Li R (2017) Laser cladding Ni-based alloy/nano-Ni encapsulated h-BN self-lubricating composite coatings. Surf Coat Technol 332:422–427. https://doi.org/10.1016/j.surfcoat.2017.06.079CrossRef

28.

Yoon S, Kim J, Kim BD, Lee C (2010) Tribological behavior of B4C reinforced Fe-base bulk metallic glass composite coating. Surf Coat Technol 205:1962–1968. https://doi.org/10.1016/j.surfcoat.2010.08.078CrossRef

29.

Zhao Y, Yu T, Guan C, Sun J, Tan X (2019) Microstructure and friction coefficient of ceramic (TiC, TiN and B4C) reinforced Ni-based coating by laser cladding. Ceram Int 45:20824–20836. https://doi.org/10.1016/j.ceramint.2019.07.070CrossRef

30.

DebRoy T, Wei HL, Zuback JS, Mukherjee T, Elmer JW, Milewski JO, Beese AM (2018) Additive manufacturing of metallic components – Process, structure and properties. Prog Mater Sci 92:112–224. https://doi.org/10.1016/j.pmatsci.2017.10.001CrossRef

31.

Zhang Z, Huang Y, Rani Kasinathan A, Imani Shahabad S, Ali U, Mahmoodkhani Y, Toyserkani E (2019) 3-Dimensional heat transfer modeling for laser powder-bed fusion additive manufacturing with volumetric heat sources based on varied thermal conductivity and absorptivity. Opt Laser Technol 109:297–312CrossRef

32.

Wei S, Wang G, Shin YC, Rong Y (2018) Comprehensive modeling of transport phenomena in laser hot-wire deposition process. Int J Heat Mass Transf 125:1356–1368. https://doi.org/10.1016/j.ijheatmasstransfer.2018.04.164CrossRef

33.

Yang L, Yu T, Li M, Zhao Y, Sun J (2018) Microstructure and wear resistance of in-situ synthesized Ti(C, N) ceramic reinforced Fe-based coating by laser cladding. Ceram Int 44:22538–22548. https://doi.org/10.1016/j.ceramint.2018.09.025CrossRef

34.

Yanan L, Ronglu S, Wei N, Tiangang Z, Yiwen L (2019) Effects of CeO₂ on microstructure and properties of TiC/Ti2Ni reinforced Ti-based laser cladding composite coatings. Opt Lasers Eng 120:84–94CrossRef

35.

Zhao Y, Yu T, Chen L, Chen Y, Guan C, Sun J (2020) Microstructure and wear resistance behavior of Ti–C–B₄C-reinforced composite coating. Ceram Int 46:25136–25148. https://doi.org/10.1016/j.ceramint.2020.06.300CrossRef

36.

Zhao J, Wang G, Wang X, Luo S, Wang L, Rong Y (2020) Multicomponent multiphase modeling of dissimilar laser cladding process with high-speed steel on medium carbon steel. Int J Heat Mass Transf 148:118990. https://doi.org/10.1016/j.ijheatmasstransfer.2019.118990CrossRef

37.

Yin Z, Yan S, Xu W, Yuan J (2018) Microwave sintering of Ti(C, N)-based cermet cutting tool material. Ceram Int 44:1034–1040CrossRef

38.

Wang KL, Zhu YM, Zhang QB, Sun ML (1997) Effect of rare earth cerium on the microstructure and corrosion resistance of laser cladded nickel-base alloy coatings. J Mater Process Technol 63:563–567. https://doi.org/10.1016/S0924-0136(96)02684-2CrossRef

39.

Qi X, Zhu S (2015) Effect of CeO₂ addition on thermal shock resistance of WC–12%Co coating deposited on ductile iron by electric contact surface strengthening. Appl Surf Sci 349:792–797CrossRef

40.

Cai Y, Luo Z, Chen Y, Ao S (2017) Influence of CeO₂ on tribological behaviour of TiC/Fe-based composite coating. Surf Eng 33:936–943CrossRef

Titel: Effects of CeO2 addition on microstructure and properties of ceramics reinforced Fe-based coatings by laser cladding
verfasst von: Liaoyuan Chen
Yu Zhao
Chuang Guan
Tianbiao Yu
Publikationsdatum: 27.05.2021
Verlag: Springer London
Erschienen in: The International Journal of Advanced Manufacturing Technology / Ausgabe 7-8/2021
Print ISSN: 0268-3768
Elektronische ISSN: 1433-3015
DOI: https://doi.org/10.1007/s00170-021-07297-8

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 7-8/2021

Milling force modeling for disc milling cutter of indexable three-sided inserts considering tool runout

Predicting the dynamic behaviour of the turning tool vibrations using an experimental measurement, numerical simulation and analytical modelling for comparative study

A multiscale analysis approach to predict mechanical properties in fused deposition modeling parts

Finite element analysis and experimental validation of high-speed laser surface hardening process

Holistic performance analysis during sustainable machining of Inconel 718 with minimum quantity lubrication-based nanofluids

In-process detection of grinding burn using machine learning

Premium Partner

Marktübersichten