Skip to main content
Erschienen in: European Journal of Wood and Wood Products 2/2020

06.02.2020 | Original

Embedment strength of mixed-species laminated veneer lumbers and cross-banded laminated veneer lumbers

verfasst von: Hoan H. Nguyen, Benoit P. Gilbert, Robert L. McGavin, Henri Bailleres, Hassan Karampour

Erschienen in: European Journal of Wood and Wood Products | Ausgabe 2/2020

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config
loading …

Abstract

This paper experimentally evaluates the embedment strength of laminated veneer lumbers (LVL) and cross-banded laminated veneer lumbers (LVL-C) manufactured from blending spotted gum (Corymbia citriodora) or white cypress pine (Callitris glaucophylla) veneers with hoop pine (Araucaria cunninghamii) veneers. Nominal 3.0 mm thick veneers were rotary peeled from small diameter (less than 30 cm) native forest sourced spotted gum and white cypress pine logs, and plantation grown hoop pine logs. 12-ply × 1.2 m (long) × 0.9 m (wide) LVL and LVL-C panels were manufactured using ten different construction strategies by mixing (i) the number of veneers from each species, (ii) the modulus of elasticity of the veneers and (iii) the veneer orientations (cross-banding). A total of 672 embedment tests, using three different dowel diameters and four different load-to-grain orientation angles, were performed using the half-hole test method described in the ASTM D5764-97a. This paper (i) compares the proportional limit strength, 5%-offset embedment strength and maximum embedment strength across the different construction strategies adopted in the study, and (ii) discusses the results in terms of load-to-grain angle and dowel diameter. More importantly, the test results are also compared to the embedment strength prediction equations detailed in the Eurocode 5 to determine their suitability for mixed-species LVL and LVL-C products. Overall, the mixed-species LVL and LVL-C showed significantly higher 5%-offset embedment strengths than single-species commercial softwood LVL products. The effect of the cross-banded veneers on the embedment strength was not found to be significant. However, the LVL-C samples exhibited a highly ductile behaviour for all load-to-grain angles and dowel diameters when compared to the LVL samples. The experimentally determined 5%-offset and maximum embedment strengths for the mixed-species LVL were on average equal to and 7% higher than the predicted values given in Eurocode 5.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

  • über 102.000 Bücher
  • über 537 Zeitschriften

aus folgenden Fachgebieten:

  • Automobil + Motoren
  • Bauwesen + Immobilien
  • Business IT + Informatik
  • Elektrotechnik + Elektronik
  • Energie + Nachhaltigkeit
  • Finance + Banking
  • Management + Führung
  • Marketing + Vertrieb
  • Maschinenbau + Werkstoffe
  • Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Springer Professional "Wirtschaft"

Online-Abonnement

Mit Springer Professional "Wirtschaft" erhalten Sie Zugriff auf:

  • über 67.000 Bücher
  • über 340 Zeitschriften

aus folgenden Fachgebieten:

  • Bauwesen + Immobilien
  • Business IT + Informatik
  • Finance + Banking
  • Management + Führung
  • Marketing + Vertrieb
  • Versicherung + Risiko




Jetzt Wissensvorsprung sichern!

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

  • über 67.000 Bücher
  • über 390 Zeitschriften

aus folgenden Fachgebieten:

  • Automobil + Motoren
  • Bauwesen + Immobilien
  • Business IT + Informatik
  • Elektrotechnik + Elektronik
  • Energie + Nachhaltigkeit
  • Maschinenbau + Werkstoffe




 

Jetzt Wissensvorsprung sichern!

Literatur
Zurück zum Zitat American Forest and Paper Association (AF&PA) (2005) National design specification for wood construction. American Wood Council American Forest and Paper Association (AF&PA) (2005) National design specification for wood construction. American Wood Council
Zurück zum Zitat AS/NZS 1080.1 (2012) Timber—methods of test—moisture content. Australian standard/New Zealand standard AS/NZS 1080.1 (2012) Timber—methods of test—moisture content. Australian standard/New Zealand standard
Zurück zum Zitat ASTM D5764-97a (2018) Evaluating dowel-bearing strength of wood and wood-based products. ASTM International, Pennsylvania ASTM D5764-97a (2018) Evaluating dowel-bearing strength of wood and wood-based products. ASTM International, Pennsylvania
Zurück zum Zitat Awaludin A, Smittakorn W, Hirai T, Hayashikawa T (2007) Bearing properties of Shorea obtusa beneath a laterally loaded bolt. J Wood Sci 53(3):204–210CrossRef Awaludin A, Smittakorn W, Hirai T, Hayashikawa T (2007) Bearing properties of Shorea obtusa beneath a laterally loaded bolt. J Wood Sci 53(3):204–210CrossRef
Zurück zum Zitat Bader TK, Schweigler M, Serrano E, Dorn M, Enquist B, Hochreiner G (2016) Integrative experimental characterization and engineering modeling of single-dowel connections in LVL. Constr Build Mater 107:235–246CrossRef Bader TK, Schweigler M, Serrano E, Dorn M, Enquist B, Hochreiner G (2016) Integrative experimental characterization and engineering modeling of single-dowel connections in LVL. Constr Build Mater 107:235–246CrossRef
Zurück zum Zitat Brancheriau L, Baillères H (2002) Natural vibration analysis of clear wooden beams: a theoretical review. Wood Sci Technol 36(4):347–365CrossRef Brancheriau L, Baillères H (2002) Natural vibration analysis of clear wooden beams: a theoretical review. Wood Sci Technol 36(4):347–365CrossRef
Zurück zum Zitat Ehlbeck J, Werner H (1992) Softwood and hardwood embedding strength for dowel type fasteners. In: International Council for Building and Inovation, Proceedings of Working Commission 18, Timber structure. Meeting 25, Paper 25-27-22, Aahus, Sweden Ehlbeck J, Werner H (1992) Softwood and hardwood embedding strength for dowel type fasteners. In: International Council for Building and Inovation, Proceedings of Working Commission 18, Timber structure. Meeting 25, Paper 25-27-22, Aahus, Sweden
Zurück zum Zitat EN1995-1-1 (2004) Eurocode 5: design of timber structures-Part 1-1: general rules and rules for buildings. European Committee for Standardisation (CEN) EN1995-1-1 (2004) Eurocode 5: design of timber structures-Part 1-1: general rules and rules for buildings. European Committee for Standardisation (CEN)
Zurück zum Zitat EN383:2007 (2007) Timber structures—test methods—determination of embedment strength and foundation values for dowel type fasteners. European Committee for Standardisation (CEN) EN383:2007 (2007) Timber structures—test methods—determination of embedment strength and foundation values for dowel type fasteners. European Committee for Standardisation (CEN)
Zurück zum Zitat Franke S, Magnière N (2014) Discussion of testing and evaluation methods for the embedment behavior of connections. In: Proceedings of the International Network on Timber Engineering Research, Paper 41-7-1, Bath Franke S, Magnière N (2014) Discussion of testing and evaluation methods for the embedment behavior of connections. In: Proceedings of the International Network on Timber Engineering Research, Paper 41-7-1, Bath
Zurück zum Zitat Franke S, Quenneville P (2011) Bolted and dowelled connections in radiata pine and laminated veneer lumber using the European yield model. Aust J Struct Eng 12(1):13–27 Franke S, Quenneville P (2011) Bolted and dowelled connections in radiata pine and laminated veneer lumber using the European yield model. Aust J Struct Eng 12(1):13–27
Zurück zum Zitat Habkirk R (2006) Bolted wood connections loaded perpendicular-to-grain: effect on wood species. Dissertation, Royal Military College of Canada Habkirk R (2006) Bolted wood connections loaded perpendicular-to-grain: effect on wood species. Dissertation, Royal Military College of Canada
Zurück zum Zitat Hassan R, Ibrahim A, Ahmad Z, Yusoff M (2014) Dowel-bearing strength properties of two tropical hardwoods. In: International civil and infrastructure engineering conference (InCIEC) 2013. Springer, Berlin, pp 27–36 Hassan R, Ibrahim A, Ahmad Z, Yusoff M (2014) Dowel-bearing strength properties of two tropical hardwoods. In: International civil and infrastructure engineering conference (InCIEC) 2013. Springer, Berlin, pp 27–36
Zurück zum Zitat Hirai T (1989) Basic properties of mechanical wood-joints, Joints 2: Bearing properties of wood under a bolt. Research Bulletins of the College Experiment Forests-Hokkaido University (Japan) Hirai T (1989) Basic properties of mechanical wood-joints, Joints 2: Bearing properties of wood under a bolt. Research Bulletins of the College Experiment Forests-Hokkaido University (Japan)
Zurück zum Zitat Hübner U (2008) Embedding strength of European hardwoods. In: Proceedings of CIB working commission W18, Timber Structures, Meeting 41, Paper 41-7-5, St. Andrews Hübner U (2008) Embedding strength of European hardwoods. In: Proceedings of CIB working commission W18, Timber Structures, Meeting 41, Paper 41-7-5, St. Andrews
Zurück zum Zitat Hwang K, Komatsu K (2002) Bearing properties of engineered wood products I: effects of dowel diameter and loading direction. J Wood Sci 48(4):295–301CrossRef Hwang K, Komatsu K (2002) Bearing properties of engineered wood products I: effects of dowel diameter and loading direction. J Wood Sci 48(4):295–301CrossRef
Zurück zum Zitat Johnsen K (1949) Theory of timber connections. Int Assoc Bridge Struct Eng 9(1):249–262 Johnsen K (1949) Theory of timber connections. Int Assoc Bridge Struct Eng 9(1):249–262
Zurück zum Zitat Kobel P, Frangi A, Steiger R (2014a) Dowel-type connections in LVL made of beech wood. In: Timber Scientific Publishing, KIT Holzbau und Baukonstruktionen, proceedings of international network on timber engineering research-meeting 47, pp 103–115, Karlsruhe Kobel P, Frangi A, Steiger R (2014a) Dowel-type connections in LVL made of beech wood. In: Timber Scientific Publishing, KIT Holzbau und Baukonstruktionen, proceedings of international network on timber engineering research-meeting 47, pp 103–115, Karlsruhe
Zurück zum Zitat Kobel P, Steiger R, Frangi A (2014b) Experimental analysis on the structural behaviour of connections with LVL made of beech wood. Materials and joints in timber structures: recent developments of technology. Springer, Dordrecht, pp 211–220CrossRef Kobel P, Steiger R, Frangi A (2014b) Experimental analysis on the structural behaviour of connections with LVL made of beech wood. Materials and joints in timber structures: recent developments of technology. Springer, Dordrecht, pp 211–220CrossRef
Zurück zum Zitat Larsen H (1973) The yield load of bolted and nailed joints. Structural Research Laboratory, Department of Structural Engineering and Materials, Technical University of Denmark, International Union of Forestry Research Organizations (IUFRO), Division 5 Larsen H (1973) The yield load of bolted and nailed joints. Structural Research Laboratory, Department of Structural Engineering and Materials, Technical University of Denmark, International Union of Forestry Research Organizations (IUFRO), Division 5
Zurück zum Zitat Leijten AJM (1993) Densified veneer: an alternative to steel plate in timber joints. Struct Eng Int 3(3):181–183CrossRef Leijten AJM (1993) Densified veneer: an alternative to steel plate in timber joints. Struct Eng Int 3(3):181–183CrossRef
Zurück zum Zitat McGavin RL, Leggate W (2019) Comparison of processing methods for small-diameter logs: sawing versus totary peeling. BioResources 14(1):1545–1565 McGavin RL, Leggate W (2019) Comparison of processing methods for small-diameter logs: sawing versus totary peeling. BioResources 14(1):1545–1565
Zurück zum Zitat McGavin RL, Leggate B, Huth J (2017) Increasing the value of forest resources through the development of advanced engineered wood products. Resource assessment report 1—availability of small-diameter peeler logs from Queensland’s native forests. Department of Agriculture and Fisheries, Brisbane, Queensland McGavin RL, Leggate B, Huth J (2017) Increasing the value of forest resources through the development of advanced engineered wood products. Resource assessment report 1—availability of small-diameter peeler logs from Queensland’s native forests. Department of Agriculture and Fisheries, Brisbane, Queensland
Zurück zum Zitat McGavin RL, Dakin T, Faircloth A, Nguyen HH (2018) Increasing the value of forest resources through the development of advanced engineered wood products. Product Performance Report 1-Mechanical properties testing of six laminated veneer lumber (LVL) products. Department of Agriculture and Fisheries, Brisbane McGavin RL, Dakin T, Faircloth A, Nguyen HH (2018) Increasing the value of forest resources through the development of advanced engineered wood products. Product Performance Report 1-Mechanical properties testing of six laminated veneer lumber (LVL) products. Department of Agriculture and Fisheries, Brisbane
Zurück zum Zitat Nguyen HH, Gilbert BP, McGavin R, Bailleres H (2019) Optimisation of cross-banded Laminated Veneer Lumber manufactured from spotted Gum and southern Pine veneers. Eur J Wood Prod 77(5):783–797CrossRef Nguyen HH, Gilbert BP, McGavin R, Bailleres H (2019) Optimisation of cross-banded Laminated Veneer Lumber manufactured from spotted Gum and southern Pine veneers. Eur J Wood Prod 77(5):783–797CrossRef
Zurück zum Zitat Quenneville P (2008) Design of bolted connections: a comparison of a proposal and various existing standards. N Z Timber Des J 17(2):3–9 Quenneville P (2008) Design of bolted connections: a comparison of a proposal and various existing standards. N Z Timber Des J 17(2):3–9
Zurück zum Zitat Quenneville JH, Mohammad M (2000) On the failure modes and strength of steel-wood-steel bolted timber connections loaded parallel-to-grain. Can J Civ Eng 27(4):761–773CrossRef Quenneville JH, Mohammad M (2000) On the failure modes and strength of steel-wood-steel bolted timber connections loaded parallel-to-grain. Can J Civ Eng 27(4):761–773CrossRef
Zurück zum Zitat Schweigler M, Bader TK, Hochreiner G, Unger G, Eberhardsteiner J (2016) Load-to-grain angle dependence of the embedment behavior of dowel-type fasteners in laminated veneer lumber. Constr Build Mater 126:1020–1033CrossRef Schweigler M, Bader TK, Hochreiner G, Unger G, Eberhardsteiner J (2016) Load-to-grain angle dependence of the embedment behavior of dowel-type fasteners in laminated veneer lumber. Constr Build Mater 126:1020–1033CrossRef
Zurück zum Zitat Stark NM, Cai Z, Carll C (2010) Wood-based composite materials: panel products, glued-laminated timber, structural composite lumber, and wood-nonwood composite materials. In: Wood handbook: wood as an engineering material. Forest Products Laboratory, Department of Agriculture and Forest Service, Madison, pp 11.11–11.28 Stark NM, Cai Z, Carll C (2010) Wood-based composite materials: panel products, glued-laminated timber, structural composite lumber, and wood-nonwood composite materials. In: Wood handbook: wood as an engineering material. Forest Products Laboratory, Department of Agriculture and Forest Service, Madison, pp 11.11–11.28
Zurück zum Zitat Whale LR, Smith I, Hilson BO (1986) Behaviour of nailed and bolted joints under short-term lateral load–conclusions from some recent research. In: Proceedings of International Council for Research and Innovation in Building and Construction (CIB) W18, 19-17-11, Florence Whale LR, Smith I, Hilson BO (1986) Behaviour of nailed and bolted joints under short-term lateral load–conclusions from some recent research. In: Proceedings of International Council for Research and Innovation in Building and Construction (CIB) W18, 19-17-11, Florence
Zurück zum Zitat Whale L, Smith I, Hilson B (1989) Characteristic properties of nailed and bolted joints under short-term lateral load, part 4–the influence of testing mode and fastener diameter upon embedment test data. J Inst Wood Sci 11(5):156–161 Whale L, Smith I, Hilson B (1989) Characteristic properties of nailed and bolted joints under short-term lateral load, part 4–the influence of testing mode and fastener diameter upon embedment test data. J Inst Wood Sci 11(5):156–161
Zurück zum Zitat Wilkinson TL (1991) Dowel bearing strength. Research Paper FPL-RP-505, Forest Products Laboratory, p 11 Wilkinson TL (1991) Dowel bearing strength. Research Paper FPL-RP-505, Forest Products Laboratory, p 11
Zurück zum Zitat Zhou T, Guan Z (2006) Review of existing and newly developed approaches to obtain timber embedding strength. Progr Struct Eng Mater 8(2):49–67CrossRef Zhou T, Guan Z (2006) Review of existing and newly developed approaches to obtain timber embedding strength. Progr Struct Eng Mater 8(2):49–67CrossRef
Metadaten
Titel
Embedment strength of mixed-species laminated veneer lumbers and cross-banded laminated veneer lumbers
verfasst von
Hoan H. Nguyen
Benoit P. Gilbert
Robert L. McGavin
Henri Bailleres
Hassan Karampour
Publikationsdatum
06.02.2020
Verlag
Springer Berlin Heidelberg
Erschienen in
European Journal of Wood and Wood Products / Ausgabe 2/2020
Print ISSN: 0018-3768
Elektronische ISSN: 1436-736X
DOI
https://doi.org/10.1007/s00107-020-01504-1

Weitere Artikel der Ausgabe 2/2020

European Journal of Wood and Wood Products 2/2020 Zur Ausgabe