nach oben

The International Journal of Life Cycle Assessment

Erschienen in:

20.07.2021 | LCA FOR MANUFACTURING AND NANOTECHNOLOGY

Evaluation and improvement of the greenness of plasma spraying through life cycle assessment and grey relational analysis

verfasst von: Jing Liu, Liming Wang, Fangyi Li, Yanle Li, Xueju Ran, Lin Kong, Yan Fu

Erschienen in: The International Journal of Life Cycle Assessment | Ausgabe 8/2021

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

Purpose

Plasma spraying is a mature, efficient, and widely applied surface treatment technology. However, the high-energy consumption and harmful gas emissions are still obstacles to achieving clean production by plasma spraying. Considering that the various process parameters of plasma spraying have great impacts on both on coating performance and environmental impact, this study attempts to improve the greenness of plasma spraying including environmental and mechanical properties, through optimizing the process parameters.

Methods

The greenness of plasma spraying means to achieve the balance of reducing environmental impact and improving the mechanical performance of coating. In this work, a Fe-based coating is prepared by plasma spraying on the basis of an L9 (3⁴) orthogonal experiment with various process parameters, i.e., power, powder feeding speed, gun speed, and track pitch. A complete life cycle assessment (LCA) study is conducted to quantify and evaluate the environmental impact of plasma spraying. In addition, the microhardness and porosity of the Fe-based coating are investigated to evaluate the mechanical performance. Finally, grey relational analysis (GRA) is used to realize multiobjective decision-making and improve the greenness of plasma spraying.

Results and discussion

LCA results show that electricity contributes most to the environmental impact of plasma spraying. When hydropower is supplied, the environmental impacts can be significantly reduced by 46.65%. Based on the L9 (3⁴) orthogonal experiment and GRA, five optimized plasma spraying schemes are proposed, i.e., microhardness optimality, porosity optimality, environmental optimality, greenness optimality, and enhanced greenness optimality. The verification shows that the enhanced greenness optimality of plasma spraying is improved by 11.83% compared with the greenness optimality.

Conclusion

In this study, we propose a method to evaluate and improve the greenness of plasma spraying both in environmental and mechanical performance through the integration of LCA and GRA, which can be adopted to optimize the spraying process parameters in real sustainable production.

Vorheriger Artikel Assessing life cycle environmental impacts of inoculating soybeans in Argentina with Bradyrhizobium japonicum

Nächster Artikel Environmental impacts of wooden, plastic, and wood-polymer composite pallet: a life cycle assessment approach

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

An Y, Hou G, Chen J, Zhao X, Liu G, Zhou H, Chen J (2014) Microstructure and tribological properties of iron-based metallic glass coatings prepared by atmospheric plasma spraying. Vacuum 107:132–140CrossRef

Baranitharan P, Ramesh K, Sakthivel R (2019) Multi-attribute decision-making approach for Aegle marmelos pyrolysis process using TOPSIS and grey relational analysis: assessment of engine emissions through novel Infrared thermography. J Cleaner Prod 234:315–328. https://doi.org/10.1016/j.jclepro.2019.06.188CrossRef

Bobzin K, Ote M, Linke TF, Sommer J, Liao X (2016) Influence of process parameter on grit blasting as a pretreatment process for thermal spraying. J Therm Spray Technol 25:3–11. https://doi.org/10.1007/s11666-015-0297-0CrossRef

Cai S, Bao G, Ma X, Wu W, Bian GB, Rodrigues JJPC, de Albuquerque VHC (2019) Parameters optimization of the dust absorbing structure for photovoltaic panel cleaning robot based on orthogonal experiment method. J Cleaner Prod 217:724–731. https://doi.org/10.1016/j.jclepro.2019.01.135CrossRef

Carvalho A, Mimoso AF, Mendes AN, Matos HA (2014) From a literature review to a framework for environmental process impact assessment index. J. Cleaner Prod. 64:36–62

Chapaneri R (2006) Environmental impact of coatings. Transactions of the Imf 84:229–230CrossRef

Chen SY, Ma GZ, Wang HD, Kang JJ, Xu BS, Wang HJ, Liu M (2016) Investigation of competing failure mechanism and life of plasma sprayed Fe-based alloy coating under rolling–sliding contact condition. Tribol Int 101:25–32CrossRef

China's electricity statistics (2019) http://www.chinapower.com.cn/sj/ndsj/20200223/7028.html

Dong Q, Zhang B, Ba Z, Li Z, Wang Z (2019) Microstructure and properties of FeCrNiMoCBSi amorphous / nanocrystalline composite coatings via plasma spraying process. Surf Topog: Metrol Prop. https://doi.org/10.1088/2051-672X/ab411bCrossRef

Euh K, Kang SB (2005) Effect of rolling on the thermo-physical properties of SiCp/Al composites fabricated by plasma spraying. Mater. Sci. Eng., A 395:47–52

Fauchais P (2004) TOPICAL REVIEW: Understanding plasma spraying. J Phys D: Appl Phys 37:86CrossRef

Guozheng M, Shuying C, Pengfei H, Haidou W, Yangyang Z, Qing Z, Guolu L (2019) Particle in-flight status and its influence on the properties of supersonic plasma-sprayed Fe-based amorphous metallic coatings. Surf Coat Technol 358:394–403CrossRef

Gupta M, Dwivedi G, Nylen P, Vackel A, Sampath S (2013) An experimental study of microstructure-property relationships in thermal barrier coatings. J Thermal Spray Technol 22:659–670. https://doi.org/10.1007/s11666-013-9915-xCrossRef

Hong Z, Guo Y, Shi S (2016) Review on several kinds of unconventional plasma spraying technique. Bull Chin Ceram Soc 35:1532–1535

Jolliet O, Margni M, Charles R, Humbert S, Payet J, Rebitzer G, Rosenbaum R (2003) IMPACT 2002+: A new life cycle impact assessment methodology. Int J Life Cycle Assess 8:324–330. https://doi.org/10.1007/bf02978505CrossRef

Klopffer W (2017) Introducing a new section in the International Journal of Life Cycle Assessment: critical review and life cycle assessment standards. Int J Life Cycle Assess 22:1015–1016. https://doi.org/10.1007/s11367-017-1328-5CrossRef

Kluczek A (2014) Application of best available techniques in an enterprise producing heating devices. J. Cleaner Prod. 83

Kumar A, Nayak SK, Bijalwan P, Dutta M, Banerjee A, Laha T (2019) Optimization of mechanical and corrosion properties of plasma sprayed low-chromium containing Fe-based amorphous/nanocrystalline composite coating. Surf Coat Technol 370:255–268. https://doi.org/10.1016/j.surfcoat.2019.05.010CrossRef

Li CJ, Sun B (2004a) Effects of spray parameters on the microstructure and property of Al 2 O 3 coatings sprayed by a low power plasma torch with a novel hollow cathode. Thin Solid Films 450:282–289CrossRef

Li CJ, Sun B (2004b) Microstructure and property of micro-plasma-sprayed Cu coating. Mater. Sci. Eng., A 379:p.92–101

Liu E, Wang F, Du S, Zeng Z, Du H, Bai Y (2019) Effect of Cr2O3 on the microstructure and tribological performance of sprayed Fe-based coating on cylinder liner. Inst. Mech. Eng, Part J, Pro. https://doi.org/10.1177/1350650119870964CrossRef

Liu M, Wang HJ, Jiang Y, Guo YM, Zhao KK (2012) Experimental analysis on the environment of internal plasma spraying techniques. In: Sung WP, Kao JCM, Chen R (eds) Frontiers of Mechanical Engineering and Materials Engineering, Pts 1 and 2, vol 184–185. Appl. Mech. Mater. Trans Tech Publications Ltd, Durnten-Zurich, pp 1480-+ https://doi.org/10.4028/www.scientific.net/AMM.184-185.1480

Liu T, Ansar A, Arnold J (2017) A study of the influence of the surrounding gas on the plasma jet and coating quality during plasma spraying. Plasma Chem Plasma Process 37:1009–1032. https://doi.org/10.1007/s11090-017-9795-9CrossRef

Luo F, Zhou W, Zhu] D, (2013) Effect of critical plasma spray parameter on complex permittivity and microstructure by plasma spraying Cr/Al2O3 coatings. Appl. Surf Sci

Martínez E, Sanz F, Pellegrini S, Jiménez E, Blanco J (2008) Life-cycle assessment of a 2-MW rated power wind turbine: CML method. Int J Life Cycle Assess 14:52–63CrossRef

Mia M et al (2019) Multi-objective optimization and life cycle assessment of eco-friendly cryogenic N-2 assisted turning of Ti-6Al-4V. J Cleaner Prod 210:121–133. https://doi.org/10.1016/j.jclepro.2018.10.334CrossRef

Moign A, Vardelle A, Themelis NJ, Legoux JG (2010) Life cycle assessment of using powder and liquid precursors in plasma spraying: the case of yttria-stabilized zirconia. Surf Coat Technol 205:668–673CrossRef

Nayak SK, Bijalwan P, Dutta M, Banerjee A, Laha] T, (2019) Optimization of mechanical and corrosion properties of plasma sprayed low-chromium containing Fe-based amorphous/nanocrystalline composite coating. Surf. Coat, Technol

Pech J, Hannoyer B (2000) Influence of oxide layer promoted by d.c. plasma preheating on the adhesion coating and role of the initial surface pretreatment. Surf Interface Anal 30:585–588. https://doi.org/10.1002/1096-9918(200008)30:1%3c585::aid-sia844%3e3.0.co;2-yCrossRef

Peng S, Li T, Li M, Guo Y, Shi J, Tan GZ, Zhang H (2019) An integrated decision model of restoring technologies selection for engine remanufacturing practice. J. Cleaner Prod 206:598-610. https://doi.org/10.1016/j.jclepro.2018.09.176

Qiao L, Wu Y, Hong S, Cheng J, Wei Z (2019) Influence of the high-velocity oxygen-fuel spray parameters on the porosity and corrosion resistance of iron-based amorphous coatings. Surf Coat Technol 366:296–302CrossRef

Quek CH, Khor KA, Cheang P (1999) Influence of processing parameters in the plasma spraying of hydroxyapatite/Ti-6Al-4V composite coatings. J Mater Process Tehnol 89–90:550–555CrossRef

Ryding SO (1999) ISO 14042 Environmental management ∙ Life cycle assessment ∙ life cycle impact assessment. Int J Life Cycle Assess 4:307–307CrossRef

S.T. et al (2012) Effect of critical plasma spray parameters on the microstructure, microhardness and wear and corrosion resistance of plasma sprayed alumina coating. Surf Coat Technol

Samadi H, Pershin L, Coyle TW (2010) Effect of in-flight particle properties on deposition of air plasma sprayed forsterite. Surf Coat Technol 204:3300–3306CrossRef

Samal S (2017) Thermal plasma technology: the prospective future in material processing. J Cleaner Prod 142:3131–3150. https://doi.org/10.1016/j.jclepro.2016.10.154CrossRef

Sarikaya O (2005) Effect of some parameters on microstructure and hardness of alumina coatings prepared by the air plasma spraying process. Surf Coat Technol 190:388–393. https://doi.org/10.1016/j.surfcoat.2004.02.007CrossRef

Serres N, Hlawka F, Costil S, Langlade C, Machi F (2010) Microstructures and environmental assessment of metallic NiCrBSi coatings manufactured via hybrid plasma spray process. Surf Coat Technol 205:1039–1046CrossRef

Su J et al (2016) Effect of critical plasma spray parameters on microstructure and microwave absorption property of Ti3SiC2/Cordierite coatings. J Therm Spray Technol 25:639–649CrossRef

Sui JL, Li MS, Lu YP, Bai YQ (2005) The effect of plasma spraying power on the structure and mechanical properties of hydroxyapatite deposited onto carbon/carbon composites. Surf Coat Technol 190:287–292CrossRef

Sun FH, Zhuang MA, Liu YR, Bao YN, Fan Y (2013) Research progress of the way to decrease plasma spraying ceramic coating porosity. B. Chin. Ceram, Soc

Thirumalaikumarasamy, Shanmugam, Balasubramanian (2013) Effect of atmospheric plasma spraying parameters on porosity level of alumina coatings. Surf, Eng

Thirumalaikumarasamy D, Kamalamoorthy KS, Visvalingam VB (2015) Effect of experimental parameters on the micro hardness of plasma sprayed alumina coatings on AZ31B magnesium alloy. J Magnesium Alloys 3:237–246. https://doi.org/10.1016/j.jma.2015.06.002CrossRef

Viana M, Fonseca AS, Querol X, López-Lilao A, Carpio P, Salmatonidis A, Monfort E (2017) Workplace exposure and release of ultrafine particles during atmospheric plasma spraying in the ceramic industry. Sci Total Environ 599–600:2065–2073CrossRef

Wang L, Ran X, Li Y, Li F, Qi X (2020) Energy consumption model of plasma spraying based on unit process life cycle inventory. J Mater Res Technol 9:15324–15334CrossRef

Xu H, Bao Y, Gawne DT, Zhang T (2016) Process control for thermal-spray deposition of thermoset coatings using computer simulation. Prog Org Coat 101:407–415CrossRef

Yan J, Xiaoping HU, Tang S, Jianguang XU (2012) Influence of spraying parameters on microstructure of molybdenum disilicide coating prepared by thermal spraying. Hot Working Technology

Yin L, Li X, Gao L, Lu C, Zhang Z (2017) Energy-efficient job shop scheduling problem with variable spindle speed using a novel multi-objective algorithm. Adv Mech Eng 9:168781401769595CrossRef

Yu Q, Zhou C, Wang X (2008) Influence of plasma spraying parameter on microstructure and photocatalytic properties of nanostructured TiO2–Fe3O4 coating. J Mol Catal A: Chem 283:23–28CrossRef

Zhang et al (2017) Optimizing process and the properties of the sprayed Fe-based metallic glassy coating by plasma spraying. Surf. Coat, TechnolCrossRef

Zhang Z, Qiang M, Liang W, Cui S, Yi X (2015) The Study on Al_2O_3–13%TiO_2 coating prepared by plasma spraying at different powers. Heat Treat

Zhu Y, Wei J, Zhou Y, Zhang Y, Li X, Ni H (2016) Current situation of plasma spraying technology. Mod Chem Ind 36:46–50

Titel: Evaluation and improvement of the greenness of plasma spraying through life cycle assessment and grey relational analysis
verfasst von: Jing Liu
Liming Wang
Fangyi Li
Yanle Li
Xueju Ran
Lin Kong
Yan Fu
Publikationsdatum: 20.07.2021
Verlag: Springer Berlin Heidelberg
Erschienen in: The International Journal of Life Cycle Assessment / Ausgabe 8/2021
Print ISSN: 0948-3349
Elektronische ISSN: 1614-7502
DOI: https://doi.org/10.1007/s11367-021-01910-4

Springer Professional

Abstract

Purpose

Methods

Results and discussion

Conclusion

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 8/2021

Comparison of life cycle assessment between lyocell fiber and viscose fiber in China

Life-cycle assessment of redwood lumber products in the US

The population equivalent as a novel approach for life cycle assessment of cities and inter-city comparisons

Life cycle assessment of dairy production systems in Inner Mongolia: reiterate LCA modeling approaches

Waste is not a service

Application of territorial emission factors with open-access data—a territorial LCA case study of land use for livestock production in Wallonia