nach oben

Journal of Materials Science

Erschienen in:

29.11.2016 | Original Paper

Tailoring particle distribution non-uniformity and grain refinement in nanostructured metal matrix composites fabricated by severe plastic deformation (SPD): a correlation with flow stress

verfasst von: E. Bagherpour, M. Reihanian, H. Miyamoto

Erschienen in: Journal of Materials Science | Ausgabe 6/2017

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

The effect of particle distribution non-uniformity on the microstructure and flow stress in nanostructured metal matrix composites produced by severe plastic deformation was investigated. The Al/SiC composite fabricated by accumulative roll bonding was considered as a case. Transmission electron microscope (TEM) and scanning transmission electron microscope (STEM) were used for microstructural characterizations. Based on the particle distribution, three different zones were considered: particle-free zone, single particle zone, and cluster zone. In comparison to the particle free zone, finer grain sizes with higher boundary misorientation angle were observed in the single particle zone. The lowest grain size (342/260 nm by TEM/STEM) was obtained in the cluster zone approximately between two near particles. The selected area diffraction showed the highest misorientation angle at these regions. A combined microstructure strengthening analysis was considered for the prediction of the flow stress. The flow stress is predicted based on the grain sizes at various microstructural zones, and the results were compared with the experimental yield stress of the composite.

Vorheriger Artikel Nucleation and growth of chimney pores during electron-beam additive manufacturing

Nächster Artikel Diamond’s third-order elastic constants: ab initio calculations and experimental investigation

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Lloyd DJ (1994) Particle reinforced aluminium and magnesium matrix composites. Int Mater Rev 39(1):1–23. doi:10.1179/imr.1994.39.1.1 CrossRef

Ibrahim IA, Mohamed FA, Lavernia EJ (1991) Particulate reinforced metal matrix composites—a review. J Mater Sci 26(5):1137–1156. doi:10.1007/bf00544448 CrossRef

Xu W, Ma H, Ji S, Chen H (2016) Analytical effective elastic properties of particulate composites with soft interfaces around anisotropic particles. Compos Sci Technol 129:10–18. doi:10.1016/j.compscitech.2016.04.011 CrossRef

Sun CJ, Saffari P, Sadeghipour K, Baran G (2005) Effects of particle arrangement on stress concentrations in composites. Mater Sci Eng 405(1–2):287–295. doi:10.1016/j.msea.2005.06.032 CrossRef

Ekici R, Kemal Apalak M, Yıldırım M, Nair F (2010) Effects of random particle dispersion and size on the indentation behavior of SiC particle reinforced metal matrix composites. Mater Des 31(6):2818–2833. doi:10.1016/j.matdes.2010.01.001 CrossRef

Bie BX, Huang JY, Su B, Lu L, Fan D, JC E, Sun T, Fezzaa K, Qi ML, Luo SN (2016) Dynamic tensile deformation and damage of B₄C-reinforced Al composites: time-resolved imaging with synchrotron x-rays. Mater Sci Eng 664:86–93. doi:10.1016/j.msea.2016.03.124 CrossRef

Sabirov I, Kolednik O (2005) The effect of inclusion size on the local conditions for void nucleation near a crack tip in a mild steel. Scr Mater 53(12):1373–1378. doi:10.1016/j.scriptamat.2005.08.027 CrossRef

Sabirov I, Duschlbauer D, Pettermann HE, Kolednik O (2005) The determination of the local conditions for void initiation in front of a crack tip for materials with second-phase particles. Mater Sci Eng 393(1–2):275–285. doi:10.1016/j.msea.2004.10.013 CrossRef

Heinrich H, Vananti A, Kostorz G (2001) Strain fields at interfaces of Al-based metal matrix composites. Mater Sci Eng 319–321:434–438. doi:10.1016/S0921-5093(01)00955-8 CrossRef

10.

Douin J, Donnadieu P, Houdellier F (2010) Elastic strain around needle-shaped particles embedded in Al matrix. Acta Mater 58(17):5782–5788. doi:10.1016/j.actamat.2010.06.053 CrossRef

11.

Yuan MN, Yang YQ, Li C, Heng PY, Li LZ (2012) Numerical analysis of the stress–strain distributions in the particle reinforced metal matrix composite SiC/6064Al. Mater Des 38:1–6. doi:10.1016/j.matdes.2011.12.043 CrossRef

12.

Chawla N, Chawla KK (2006) Microstructure-based modeling of the deformation behavior of particle reinforced metal matrix composites. J Mater Sci 41(3):913–925. doi:10.1007/s10853-006-6572-1 CrossRef

13.

Sabirov I, Kolednik O, Valiev RZ, Pippan R (2005) Equal channel angular pressing of metal matrix composites: effect on particle distribution and fracture toughness. Acta Mater 53(18):4919–4930. doi:10.1016/j.actamat.2005.07.010 CrossRef

14.

Wu X, Xia K (2007) Back pressure equal channel angular consolidation—application in producing aluminium matrix composites with fine flyash particles. J Mater Process Technol 192–193:355–359. doi:10.1016/j.jmatprotec.2007.04.007 CrossRef

15.

Sabbaghianrad S, Langdon TG (2016) Developing superplasticity in an aluminum matrix composite processed by high-pressure torsion. Mater Sci Eng 655:36–43. doi:10.1016/j.msea.2015.12.078 CrossRef

16.

Alhajeri SN, Al-Fadhalah KJ, Almazrouee AI, Langdon TG (2016) Microstructure and microhardness of an Al-6061 metal matrix composite processed by high-pressure torsion. Mater Charact 118:270–278. doi:10.1016/j.matchar.2016.06.003 CrossRef

17.

Reihanian M, Jalili Shahmansouri M, Khorasanian M (2015) High strength Al with uniformly distributed Al₂O₃ fragments fabricated by accumulative roll bonding and plasma electrolytic oxidation. Mater Sci Eng 640:195–199. doi:10.1016/j.msea.2015.05.104 CrossRef

18.

Reihanian M, Hadadian FK, Paydar MH (2014) Fabrication of Al–2 vol% Al2O₃/SiC hybrid composite via accumulative roll bonding (ARB): an investigation of the microstructure and mechanical properties. Mater Sci Eng 607:188–196. doi:10.1016/j.msea.2014.04.013 CrossRef

19.

Daneshvar F, Reihanian M, Gheisari K (2016) Al-based magnetic composites produced by accumulative roll bonding (ARB). Mater Sci Eng 206:45–54. doi:10.1016/j.mseb.2016.01.003 CrossRef

20.

Valiev RZ, Islamgaliev RK, Alexandrov IV (2000) Bulk nanostructured materials from severe plastic deformation. Prog Mater Sci 45(2):103–189. doi:10.1016/S0079-6425(99)00007-9 CrossRef

21.

Meyers MA, Mishra A, Benson DJ (2006) Mechanical properties of nanocrystalline materials. Prog Mater Sci 51(4):427–556. doi:10.1016/j.pmatsci.2005.08.003 CrossRef

22.

Schmidt CW, Knieke C, Maier V, Höppel HW, Peukert W, Göken M (2011) Accelerated grain refinement during accumulative roll bonding by nanoparticle reinforcement. Scr Mater 64(3):245–248. doi:10.1016/j.scriptamat.2010.10.013 CrossRef

23.

Jamaati R, Toroghinejad MR (2010) Application of ARB process for manufacturing high-strength, finely dispersed and highly uniform Cu/Al₂O₃ composite. Mater Sci Eng 527(27–28):7430–7435. doi:10.1016/j.msea.2010.08.038 CrossRef

24.

Yazdani A, Salahinejad E (2011) Evolution of reinforcement distribution in Al–B₄C composites during accumulative roll bonding. Mater Des 32(6):3137–3142. doi:10.1016/j.matdes.2011.02.063 CrossRef

25.

Rezayat M, Akbarzadeh A, Owhadi A (2012) Fabrication of high-strength Al/SiC p nanocomposite sheets by accumulative roll bonding. Metall Mater Trans A 43(6):2085–2093. doi:10.1007/s11661-011-1039-7 CrossRef

26.

Jamaati R, Toroghinejad MR, Edris H (2014) Effect of SiC nanoparticles on the mechanical properties of steel-based nanocomposite produced by accumulative roll bonding process. Mater Des 54:168–173. doi:10.1016/j.matdes.2013.08.033 CrossRef

27.

Alizadeh M (2010) Comparison of nanostructured Al/B₄C composite produced by ARB and Al/B₄C composite produced by RRB process. Mater Sci Eng 528(2):578–582. doi:10.1016/j.msea.2010.08.093 CrossRef

28.

Alizadeh M, Paydar MH, Terada D, Tsuji N (2012) Effect of SiC particles on the microstructure evolution and mechanical properties of aluminum during ARB process. Mater Sci Eng 540:13–23. doi:10.1016/j.msea.2011.12.026 CrossRef

29.

Alizadeh M, Paydar MH (2010) Fabrication of nanostructure Al/SiCP composite by accumulative roll-bonding (ARB) process. J Alloy Compd 492(1–2):231–235. doi:10.1016/j.jallcom.2009.12.026 CrossRef

30.

Saito Y, Utsunomiya H, Tsuji N, Sakai T (1999) Novel ultra-high straining process for bulk materials—development of the accumulative roll-bonding (ARB) process. Acta Mater 47(2):579–583. doi:10.1016/S1359-6454(98)00365-6 CrossRef

31.

Saito Y, Tsuji N, Utsunomiya H, Sakai T, Hong RG (1998) Ultra-fine grained bulk aluminum produced by accumulative roll-bonding (ARB) process. Scr Mater 39(9):1221–1227. doi:10.1016/S1359-6462(98)00302-9 CrossRef

32.

Reihanian M, Bagherpour E, Paydar MH (2013) On the achievement of uniform particle distribution in metal matrix composites fabricated by accumulative roll bonding. Mater Lett 91:59–62. doi:10.1016/j.matlet.2012.09.043 CrossRef

33.

Courtney TH (2000) Mechanical behavior of materials. McGraw Hill, Boston, pp 212–218

34.

Nardone VC, Prewo KM (1986) On the strength of discontinuous silicon carbide reinforced aluminum composites. Scr Metall 20(1):43–48. doi:10.1016/0036-9748(86)90210-3 CrossRef

35.

Sekine H, Chent R (1995) A combined microstructure strengthening analysis of SiCp/Al metal matrix composites. Composites 26(3):183–188. doi:10.1016/0010-4361(95)91381-E CrossRef

36.

Arsenault RJ, Shi N (1986) Proceedings of the international conference on low energy dislocation structures dislocation generation due to differences between the coefficients of thermal expansion. Mater Sci Eng 81:175–187. doi:10.1016/0025-5416(86)90261-2 CrossRef

37.

Hansen N (2004) Hall–Petch relation and boundary strengthening. Scr Mater 51(8):801–806. doi:10.1016/j.scriptamat.2004.06.002 CrossRef

38.

Ashby MF (1966) Work hardening of dispersion-hardened crystals. Philos Mag 14(132):1157–1178. doi:10.1080/14786436608224282 CrossRef

39.

Fleck NA, Ashby MF, Hutchinson JW (2003) The role of geometrically necessary dislocations in giving material strengthening. Scr Mater 48(2):179–183. doi:10.1016/S1359-6462(02)00338-X CrossRef

40.

Ferguson JB, Lopez H, Kongshaug D, Schultz B, Rohatgi P (2012) Revised Orowan strengthening: effective interparticle spacing and strain field considerations. Metall Mater Trans A 43(6):2110–2115. doi:10.1007/s11661-011-1029-9 CrossRef

41.

Zhang Z, Chen DL (2006) Consideration of Orowan strengthening effect in particulate-reinforced metal matrix nanocomposites: a model for predicting their yield strength. Scr Mater 54(7):1321–1326. doi:10.1016/j.scriptamat.2005.12.017 CrossRef

42.

Bay B, Hansen N, Hughes DA, Kuhlmann-Wilsdorf D (1992) Overview no. 96 evolution of f.c.c. deformation structures in polyslip. Acta Metall Mater 40(2):205–219. doi:10.1016/0956-7151(92)90296-Q CrossRef

43.

Hughes DA, Hansen N (1997) High angle boundaries formed by grain subdivision mechanisms. Acta Mater 45(9):3871–3886. doi:10.1016/S1359-6454(97)00027-X CrossRef

44.

Kuhlmann-Wilsdorf D, Hansen N (1991) Geometrically necessary, incidental and subgrain boundaries. Scr Metall Mater 25(7):1557–1562. doi:10.1016/0956-716X(91)90451-6 CrossRef

Titel: Tailoring particle distribution non-uniformity and grain refinement in nanostructured metal matrix composites fabricated by severe plastic deformation (SPD): a correlation with flow stress
verfasst von: E. Bagherpour
M. Reihanian
H. Miyamoto
Publikationsdatum: 29.11.2016
Verlag: Springer US
Erschienen in: Journal of Materials Science / Ausgabe 6/2017
Print ISSN: 0022-2461
Elektronische ISSN: 1573-4803
DOI: https://doi.org/10.1007/s10853-016-0632-y

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 6/2017

Parametric study of protein-encapsulated microcapsule formation and effect on self-healing efficiency of ‘green’ soy protein resin

The effect of para-divinyl benzene on styrenic emulsion-templated porous polymers: a chemical Trojan horse

Ultraviolet to far-infrared transmission properties of thin film multi-walled carbon nanotube random networks

Effect of different complexing agents on Pb–Co thin-film electrodeposition

Macro- and micromechanical behaviors of poly(lactic acid)–hydroxyapatite electrospun composite scaffolds

Cellulose nanocrystals as new bio-based coating layer for improving fiber-based mechanical and barrier properties

Premium Partner

Marktübersichten