nach oben

Bulletin of Engineering Geology and the Environment

Erschienen in:

24.12.2016 | Original Paper

Relationships between the drilling rate index and physicomechanical rock properties

verfasst von: Mehmet Capik, Ali Osman Yilmaz, Serdar Yasar

Erschienen in: Bulletin of Engineering Geology and the Environment | Ausgabe 1/2017

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

The drilling rate index (DRI) is an important parameter that influences the drillability of rocks. It can easily be used when estimating the economics of any excavation operation. Therefore, in the current study, an attempt was made to investigate the rock properties that govern the DRI. The relationships between the DRI and some physicomechanical rock properties were investigated based on data obtained from experimental work and in situ studies performed in different tunnels. Regression analysis was employed to develop models for estimating the DRI based on physicomechanical rock properties. The derived models were verified based on the behavior of the determination coefficient, the t test, and the F test. The study showed that the DRI decreases with increasing uniaxial compressive strength, point load strength, Brazilian tensile strength, and Schmidt rebound hardness. It was also concluded that the DRI increases with increasing apparent porosity and void ratio. Additionally, modeling results revealed that the proposed models can be successfully used as tools to forecast the DRI.

Vorheriger Artikel An excavatability classification system for surface excavation in sedimentary rocks

Nächster Artikel Deformation and failure of a tunnel in the restraining bend of a strike–slip fault zone: an example from Hengshan Mountain, Shanxi Province, China

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Akun ME, Karpuz C (2005) Drillability studies of surface-set diamond drilling in Zonguldak Region sandstones from Turkey. Int J Rock Mech Min Sci 42:473–479CrossRef

ASTM (2005) Standard test method for determination of rock hardness by rebound hammer method, D873-05. American Standards for Testing and Materials, West Conshohocken

ASTM (2010a) Standard test method for compressive strength and elastic moduli of intact rock core specimens under varying states of stress and temperatures, D7012-10. American Standards for Testing and Materials, West Conshohocken

ASTM (2010b) Standard test methods for apparent porosity, water absorption, apparent specific gravity, and bulk density of burned refractory brick and shapes by boiling water, C20-00. American Standards for Testing and Materials, West Conshohocken

Aydin G (2014) Modeling of energy consumption based on economic and demographic factors: the case of Turkey with projections. Renew Sustain Energy Rev 35:382–389CrossRef

Aydin G, Karakurt I, Aydiner K (2013a) Investigation of the surface roughness of rocks sawn by diamond sawblades. Int J Rock Mech Min Sci 61:171–182

Aydin G, Karakurt I, Aydiner K (2013b) Wear performance of saw blades in processing of granitic rocks and development of models for wear estimation. Rock Mech Rock Eng 46(6):1559–1575CrossRef

Berman ME, Wang J (2011) Essential statistics for public managers and policy analysts, 3rd edn. CQ, Washington, DC, p 321

Bilgin N, Kahraman S (2003) Drillability prediction in rotary blast hole drilling. In: 18th Int Mining Congr Exhib Turkey (IMCET 2003), Antalya, Turkey, 10–13 June 2003, pp 177–182

Bruland A (1998) Hard rock tunnel boring, drillability test methods, project report 13A-98. Trondheim, NTNU, p 25

Bruland A, Dahlo TS, Nilsen B (1995) Tunnelling performance estimation based on drillability testing. In: Proc 8th Int Congr Rock Mech, Tokyo, Japan, 25–30 Sept 1995, pp 123–126

Capik M, Yilmaz AO, Yasar S, Yarali O, Cavusoglu I (2013) Comparison of drillability and abrasivity properties of rocks (in Turkish). In: 23rd Int Mining Congr Exhib Turkey (IMCET 2013), Antalya, Turkey, 16–19 April 2013, pp 659–669

Dahl F (2003) DRI, BWI, CLI standards. NTNU, Trondheim, p 20

Dahl F, Grøv E, Breivik T (2007) Development of a new direct test method for estimating cutter life, based on the Sievers’ J miniature drill test (technical note). Tunn Undergr Space Technol 22:106–116

Dahl F, Bruland A, Grov E, Nilsen B (2010) Trademarking the NTNU/SINTEF drillability test indices. Tunnels Tunn Int 44–46

Dahl F, Bruland A, Jakobsen PD, Nilsen B, Grøv E (2012) Classifications of properties influencing the drillability of rocks, based on the NTNU/SINTEF test method. Tunn Undergr Space Technol 28:150–158

Demirdağ S, Sengün N, Uğur İ, Efe T, Akbay D, Altindağ R (2014) Variation of vertical and horizontal drilling rates depending on some rock properties in the marble quarries. Int J Min Sci Technol 24:269–273CrossRef

Ersoy A, Waller MD (1995) Textural characterization of rocks. Eng Geol 39:123–136CrossRef

Franklin JA, Vogler UW, Szlavin J, Edmond JM, Bieniawski ZT (2007) Suggested methods for determining water-content, porosity, density, absorption and related properties and swelling and slake-durability index properties. In: Ulusay R, Hudson JA (eds) The complete ISRM suggested methods for rock characterization, testing and monitoring; 1974–2006. ISRM Turkish National Group, Ankara, pp 83–98

Hoseinie SH, Aghababaei H, Pourrahimian Y (2008) Development of a new classification system for assessing of rock mass drillability index (RDi). Int J Rock Mech Min Sci 45:1–10

Howarth DF, Rowland JC (1987) Quantitative assessment of rock texture and correlation with drillability and strength properties. Rock Mech Rock Eng 20:57–85

ISRM (1979) Suggested method for determining the uniaxial compressive strength and deformability of rock materials. Int J Rock Mech Min Sci Geomech Abstr 16:135–140

ISRM (1981) Suggested methods for determining hardness and abrasiveness of rocks. In: Ulusay R, Hudson JA (eds) The complete ISRM suggested methods for rock characterization, testing and monitoring; 1974–2006. ISRM Turkish National Group, Ankara, 3:101–103

ISRM (1985) Suggested method for determining point load strength. Int J Rock Mech Min Sci Geomech Abstr 22:51–60CrossRef

Kahraman S, Balci C, Yazici S, Bilgin N (2000) Prediction of the penetration rate of rotary blast hole drilling using a new drillability index. Int J Rock Mech Min Sci 37:729–743CrossRef

Lien R (1961) An indirect test method for estimating the drillability of rocks. Doctoral dissertation. Department of Geology, NTH, Trondheim

Saeidi O, Torabi SR, Ataei M (2013) Development of a new index to assess the rock mass drillability. Geotech Geol Eng 31:1477–1495CrossRef

Singh TN, Gupta AR, Sain R (2006) A comparative analysis of cognitive system for the prediction of drillability of rocks and wear factor. Geotech Geol Eng 24:299–312CrossRef

Thuro K (1996) Drillability prediction in hard rock tunnelling. In: Conf on Prediction in Geology, Amsterdam, Netherlands, 22–24 Feb 1996, pp 103–108

Thuro K (1997) Drillability prediction—geological influences in hard rock drill and blast tunneling. Geol Rundsch 86:426–438CrossRef

Thuro K, Spaun G (1996) Drillability in hard rock drill and blast tunneling. Felsbau 14(2):1–11

Yaralı O (2008) Kayaçların Delinebilirlik ve Aşındırıcılıklarının Belirlenmesi. Türkiye 16. Kömür Kongresi Bildiriler Kitabı. TMMOB Maden Mühendisleri Odası Yayını, Zonguldak, pp 65–76

Yaralı O, Kahraman S (2011) The drillability assessment of rocks using the different brittleness values. Tunn Undergr Space Technol 26:406–414CrossRef

Yarali O, Soyer E (2013) Assessment of relationships between drilling rate index and mechanical properties of rocks. Tunn Undergr Space Technol 33:46–53CrossRef

Yasar S, Capik M, Yılmaz AO (2015) Cuttability assessment using the drilling rate index (DRI). Bull Eng Geol Environ 74:1349. doi:10.1007/s10064-014-0715-4

Zare S, Bruland A (2013) Applications of NTNU/SINTEF drillability indices in hard rock tunneling. Rock Mech Rock Eng 46:179–187CrossRef

Titel: Relationships between the drilling rate index and physicomechanical rock properties
verfasst von: Mehmet Capik
Ali Osman Yilmaz
Serdar Yasar
Publikationsdatum: 24.12.2016
Verlag: Springer Berlin Heidelberg
Erschienen in: Bulletin of Engineering Geology and the Environment / Ausgabe 1/2017
Print ISSN: 1435-9529
Elektronische ISSN: 1435-9537
DOI: https://doi.org/10.1007/s10064-016-0991-2

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Technik"

Springer Professional "Wirtschaft+Technik"

Weitere Artikel der Ausgabe 1/2017

Some carbonate rock texture effects on mechanical behavior, based on Koohrang tunnel data, Iran

Brittle mechanical characteristics of hard rock exposed to moisture

Performance evaluation of existing surface excavation assessment methods on weathered sedimentary rock

Constructional geomaterials: versatile earth resources in the service of humankind—introduction to the thematic set of papers on: challenges to supply and quality of geomaterials used in construction

Role of composition and fabric of Kuttanad clay: a geotechnical perspective

Nanostructured TiO2 for stone coating: assessing compatibility with basic stone’s properties and photocatalytic effectiveness