nach oben

Journal of Material Cycles and Waste Management

Erschienen in:

22.05.2018 | ORIGINAL ARTICLE

Potential utilization of rubberwood flour and sludge waste from natural rubber manufacturing process as reinforcement in plastic composites

verfasst von: Chatree Homkhiew, Worapong Boonchouytan, Watthanaphon Cheewawuttipong, Thanate Ratanawilai

Erschienen in: Journal of Material Cycles and Waste Management | Ausgabe 3/2018

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

The present study aims to evaluate and compare the potential of rubberwood flour (RWF) and sludge waste from manufacturing process of the concentrated natural rubber latex as reinforcement in recycled high-density polyethylene (rHDPE) composites. Morphological, thermal, mechanical and physical properties were investigated. The results indicated that the tensile modulus (TM), modulus of elasticity (MOE) and hardness of rHDPE composites containing sludge waste flour (SWF) were improved with the increasing amount of SWF; however, the tensile strength (TS), modulus of rupture (MOR) and water absorption (WA) exhibited a negative correlation with the SWF concentration. The composites based on SWF exhibited better TS, MOR, maximum flexural strain and WA than that of based on RWF. The thermal experiments showed that the decomposition temperatures of the rHDPE composites with SWF were higher than that of with RWF. Further, the addition of maleic anhydride-grafted polyethylene improved the mechanical and physical properties of the composites reinforcing the SWF or RWF. The above results showed that the utilization of latex sludge waste could become a promising way for solving the environmental problem as well as improving many properties of plastic composites.

Vorheriger Artikel Sink–float density separation of post-consumer plastics for feedstock recycling

Nächster Artikel Influence of liquid- and solid-state coupling anaerobic digestion process on methane production of cow manure and rice straw

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Tekprasit V (2000) The utilization of the centrifuged residue from concentrated latex industry as a soil conditioner. Thesis, Prince of Songkla University

Vichaphund S, Intiya W, Kongkaew A, Loykulnant S, Thavorniti P (2012) Utilization of sludge waste from natural rubber manufacturing process as a raw material for clay-ceramic production. Environ Technol 33(22):2507–2510CrossRef

Intiya W, Thepsuwan U, Sirisinha C, Sae-Oui P (2017) Possible use of sludge ash as filler in natural rubber. J Mater Cycles Waste Manag 19:774–781CrossRef

Taweepreda W (2013) Rubber recovery from centrifuged natural rubber latex residue using sulfuric acid. Songklanakarin J Sci Technol 35(2):213–216

Boonsawang P, Laeh S, Intrasungkha N (2008) Enhancement of sludge granulation in anaerobic treatment of concentrated latex wastewater. Songklanakarin J Sci Technol 30(Suppl.1):111–119

Soucy J, Koubaa A, Migneaulta S, Riedl B (2014) The potential of paper mill sludge for wood–plastic composites. Ind Crops Prod 54:248–256CrossRef

Hamzeh Y, Ashori A, Mirzaei B (2011) Effects of waste paper sludge on the physico-mechanical properties of high density polyethylene/wood flour composites. J Polym Environ 19:120–124CrossRef

Ayrilmis N, Buyuksari U (2010) Utilization of olive mill sludge in manufacture of lignocellulosic/polypropylene composite. J Mater Sci 45:1336–1342CrossRef

Keskisaari A, Karki T (2016) Raw material potential of recyclable materials for fiber composites: a review study. J Mater Cycles Waste Manag. https://doi.org/10.1007/s10163-016-0511-2

10.

Homkhiew C, Ratanawilai T, Thongruang W (2015) Minimizing the creep of recycled polypropylene/rubberwood flour composites with mixture design experiments. J Compos Mater 49:17–26CrossRef

11.

Adhikary KB, Pang S, Staiger MP (2008) Dimensional stability and mechanical behaviour of wood–plastic composites based recycled and virgin high-density polyethylene (HDPE). Compos Part B Eng 39(5):807–815CrossRef

12.

Yao F, Wu Q, Lei Y, Xu Y (2008) Rice straw fiber-reinforced high-density polyethylene composite: effect of fiber type and loading. Ind Crop Prod 28(1):63–72CrossRef

13.

Wu C, Williams PT (2010) Pyrolysis-gasification of post-consumer municipal solid plastic waste for hydrogen production. Int J Hydrogen Energy 35:949–957CrossRef

14.

Parparita E, Uddin A, Watanabe T, Kato Y, Yanik J, Vasile C (2015) Gas production by steam gasification of polypropylene/biomass waste composites in a dual-bed reactor. J Mater Cycles Waste Manag 17:756–768CrossRef

15.

Homkhiew C, Ratanawilai T, Thongruang W (2014) Optimizing the formulation of polypropylene and rubberwood flour composites for moisture resistance by mixture design. J Reinf Plast Compos 33:810–823CrossRef

16.

Khan ZA, Kamaruddin S, Siddiquee AN (2010) Feasibility study of use of recycled high density polyethylene and multi response optimization of injection moulding parameters using combined grey relational and principal component analyses. Mater Des 31(6):2925–2931CrossRef

17.

Ratanawilai T, Nakawirot K, Deachsrijan A, Homkhiew C (2014) Influence of wood species and particle size on mechanical and thermal properties of wood-polypropylene composites. Fibers Polym 15(10):2160–2168CrossRef

18.

Väisänen T, Haapala A, Lappalainen R, Tomppo L (2016) Utilization of agricultural and forest industry waste and residues in natural fiber-polymer composites: a review. Waste Manag 54:62–73CrossRef

19.

Sommerhuber PF, Welling J, Krause A (2015) Substitution potentials of recycled HDPE and wood particles from post-consumer packaging waste in wood–plastic composites. Waste Manag 46:76–85CrossRef

20.

Zadeh KM, Ponnamma D, Al-Maadeed MAA (2017) Date palm fibre filled recycled ternary polymer blend composites with enhanced flame retardancy. Polym Test 61:341–348CrossRef

21.

Al-Kaabi K, Al-Khanbashi A, Hammami A (2005) Date palm fibers as polymeric matrix reinforcement: DPF/polyester composite properties. Polym Compos 26:604–613CrossRef

22.

Petchpradab P, Yoshida T, Charinpanitkul T, Matsumura Y (2009) Hydrothermal pretreatment of rubber wood for the saccharification process. Ind Eng Chem Res 48(9):4587–4591CrossRef

23.

Devi RR, Maji TK (2002) Studies of properties of rubber wood with impregnation of polymer. Bull Mater Sci 25:527–531CrossRef

24.

Wu H, Liang X, Huang L, Xie Y, Tan S, Cai X (2016) The utilization of cotton stalk bark to reinforce the mechanical and thermal properties of bio-flour plastic composites. Constr Build Mater 118:337–343CrossRef

25.

Yang S, Bai S, Wang Q (2016) Morphology, mechanical and thermal oxidative aging properties of HDPE composites reinforced by nonmetals recycled from waste printed circuit boards. Waste Manag 57:168–175CrossRef

26.

Ponnamma D, George J, Thomas MG, Han CC, Valic´ S, Mozetic M, Cvelbar U, Thomas S (2015) Investigation on the thermal and crystallization behavior of high density polyethylene/acrylonitrile butadiene rubber blends and their composites. Polym Eng Sci 55:1203–1210CrossRef

27.

Sadasivuni KK, Saiter A, Gautier N, Thomas S, Grohens Y (2013) Effect of molecular interactions on the performance of poly(isobutylene-co-isoprene)/graphene and clay nanocomposites. Colloid Polym Sci 291:1729–1740CrossRef

28.

Xu K, Tu D, Chen T, Zhong T, Lu J (2016) Effects of environmental-friendly modified rubber seed shell on the comprehensive properties of high density polyethylene/rubber seed shell composites. Ind Crop Prod 91:132–141CrossRef

29.

Yang H, Yan R, Chen H, Lee DH, Zheng C (2007) Characteristics of hemicellulose, cellulose and lignin pyrolysis. Fuel 86(12–13):1781–1788CrossRef

30.

Essabir H, Boujmal R, Bensalah MO, Rodrigue D, Bouhfid R, Qaiss A (2016) Mechanical and thermal properties of hybrid composites: oil-palm fiber/clay reinforced high density polyethylene. Mech Mater 98:36–43CrossRef

31.

Ayrilmisa N, Kaymakci A, Gülec T (2015) Potential use of decayed wood in production of wood plastic composite. Ind Crop Prod 74:279–284CrossRef

32.

Mattos BD, Misso AL, Cademartori PHG, Limad EA, Washington LE, Magalhãesd WLE, Gatto DA (2014) Properties of polypropylene composites filled with a mixture of household waste of mate-tea and wood particles. Constr Build Mater 61:60–68CrossRef

33.

Ratanawilai T, Thanawattanasirikul N, Homkhiew C (2012) Mechanical and thermal properties of oil palm wood sawdust reinforced post-consumer polyethylene composites. ScienceAsia 38:289–294CrossRef

34.

Sheshmani S, Amini R (2013) Preparation and characterization of some graphene based nanocomposite materials. Carbohydr Polym 95(1):348–359CrossRef

35.

Nourbakhsh A, Ashori A, Tabari HZ, Rezaei F (2010) Mechanical and thermo-chemical properties of wood-flour/polypropylene blends. Polym Bull 65(7):691–700CrossRef

36.

Ashori A, Nourbakhsh A (2009) Mechanical behavior of agro-residue-reinforced polypropylene composites. J Appl Polym Sci 111(5):2616–2620CrossRef

37.

Kord B (2011) Effect of wood flour content on the hardness and water uptake of thermoplastic polymer composites. World Appl Sci J 12:1632–1634

38.

Rahman MR, Huque MM, Islam MN, Hasan M (2008) Improvement of physico-mechanical properties of jute fiber reinforced polypropylene composites by post-treatment. Compos Part A Appl Sci Manuf 39(11):1739–1747CrossRef

39.

Law TT, Mohd Ishak ZA (2011) Water absorption and dimensional stability of short kenaf fiber-filled polypropylene composites treated with maleated polypropylene. J Appl Polym Sci 120(1):563–572CrossRef

40.

Homkhiew C, Ratanawilai T, Thongruang W (2016) Long-term water absorption and dimensional stability of composites from recycled polypropylene and rubberwood flour. J Thermoplast Compos Mater 29(1):74–91CrossRef

41.

Adhikary KB, Pang S, Staiger MP (2008) Long-term moisture absorption and thickness swelling behaviour of recycled thermoplastics reinforced with Pinus radiate sawdust. Chem Eng J 142(2):190–198CrossRef

42.

Shakeri A, Ghasemian A (2010) Water absorption and thickness swelling behavior of polypropylene reinforced with hybrid recycled newspaper and glass fiber. Appl Compos Mater 17(2):183–193CrossRef

43.

Lin Q, Zhou X, Dai J (2002) Effect of hydrothermal environment on moisture absorption and mechanical properties of wood flour-filled polypropylene composites. J Appl Polym Sci 85(14):2824–2832CrossRef

44.

Sathishkumar TP, Navaneethakrishnan P, Shankar S et al (2013) Mechanical properties and water absorption of snake grass longitudinal fiber reinforced isophthalic poly-ester composites. J Reinf Plast Compos 32:1211–1223CrossRef

45.

Ashori A, Sheshmani S (2010) Hybrid composites made from recycled materials: moisture absorption and thickness swelling behavior. Bioresour Technol 101(12):4717–4720CrossRef

46.

Ghasemi I, Kord B (2009) Long-term water absorption behaviour of polypropylene/wood flour/organoclay hybrid nanocomposite. Iran Polym J 18(9):683–691

Titel: Potential utilization of rubberwood flour and sludge waste from natural rubber manufacturing process as reinforcement in plastic composites
verfasst von: Chatree Homkhiew
Worapong Boonchouytan
Watthanaphon Cheewawuttipong
Thanate Ratanawilai
Publikationsdatum: 22.05.2018
Verlag: Springer Japan
Erschienen in: Journal of Material Cycles and Waste Management / Ausgabe 3/2018
Print ISSN: 1438-4957
Elektronische ISSN: 1611-8227
DOI: https://doi.org/10.1007/s10163-018-0749-y

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 3/2018

Approach to the management of magnesium slag via the production of Portland cement clinker

Application of analytical hierarchy process (AHP) to assess options of energy recovery from municipal solid waste: a case study in Tehran, Iran

Contribution to closing the loop on waste materials: valorization of bottom ash from waste-to-energy plants under a life cycle approach

Laboratory investigation on high- and low-temperature performances of asphalt mastics modified by waste oil shale ash

Socio-demographic determinants of municipal waste generation: case study of the Czech Republic

Catalytic upgrading pyrolysis of pine sawdust for bio-oil with metal oxides