nach oben

Journal of Materials Engineering and Performance

Erschienen in:

01.07.2012

Producing Ultrafine Grain Al6061 Alloy by Accumulative Back Extrusion Process

verfasst von: H. Alihosseini, G. Faraji, K. Dehghani

Erschienen in: Journal of Materials Engineering and Performance | Ausgabe 7/2012

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

Accumulative back extrusion (ABE) is a kind of severe plastic deformation process to refine the microstructure, resulting in significant improvement in mechanical properties. In the present study, AA6061-T6 alloy was subjected to a newly designed ABE process at room temperature. One cycle of ABE was employed to the workpiece. The microstructural evolution was then characterized using optical microscopy and transmission electron microscopy (TEM) techniques. The results show that after one cycle of ABE, significant grain refinement was achieved. This led to the formation of ultrafine grains of smaller than 1 μm. Besides, there was about a two-fold increase in the hardness, increasing from approximately 88 Hv to 155-160 Hv after only one cycle of ABE.

Vorheriger Artikel Facile Design and Fabrication of Two-Way Shape Memory TiNi Springs with Narrow Hysteresis

Nächster Artikel Effect of Hot Working on Structure and Tribological Properties of Aluminium Reinforced with Aluminium Oxide Particulates

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

R.Z. Valiev, R.K. Islamgaliev, and I.V. Alexandrov, Bulk Nanostructured Materials from Severe Plastic Deformation, Prog. Mater. Sci., 2000, 45, p 103–189.CrossRef

Y. Saito, H. Utsunomiya, N. Tsuji, and T. Sakai, Novel UltraHigh Straining Process for Bulk Materials Development of the Accumulative Roll Bonding ARB, Acta Mater., 1999, 47, p 579–583.CrossRef

Y. Huang and P.B. Prangnell, Continuous Frictional Angular Extrusion and Its Application in the Production of Ultrafine-Grained Sheet Metals, Scr. Mater., 2007, 56, p 333–336.CrossRef

V.V. Stolyarov, Y.T. Zhu, I.V. Alexandrov, T.C. Lowe, and R.Z. Valiev, Grain Refinement and Properties of Pure Ti Processed by Warm ECAP and Cold Rolling, Mater. Sci. Eng., 2003, A343, p 43–50.

P.K. Chaudhury, B. Cherukuri, and R. Srinivasan, Scaling Up of Equal Channel Angular Pressing (ECAP) and Its Effect on Mechanical Properties, Microstructure, and Hot Workability of AA 6061, Mater. Sci. Eng., 2005, A410–411, p 316–318.

C. Xu, M. Furukawa, Z. Horita, and T.G. Langdon, The Evolution of Homogeneity and Grain Refinement During Equal-Channel Angular Pressing: A Model for Grain Refinement in ECAP, Mater. Sci. Eng., 2005, A398, p 66–76.

B.S. Moon, H.S. Kim, and S.I. Hong, Plastic Flow and Deformation Homogeneity of 6061 Al During Equal Channel Angular Pressing, Scr. Mater. A, 2002, 46, p 131–136.CrossRef

T. Inoue, S. Turizuka, and K. Nagai, Evaluating of Torsional Strain on Processing by High-Pressure Torsion, Mater. Sci. Technol., 2002, 18, p 1007–1010.CrossRef

S. Ferrasse, V.M. Segal, K.T. Hartwig, and R.E. Goforth, Development of a Submicrometer-Grained Microstructure in Aluminum 6061 Using Equal Channel Angular Extrusion, J. Mater. Res., 1997, 12, p 1253–1261.CrossRef

10.

A. Loucifa, R.B. Figueiredob, T. Baudinc, F. Brissetc, and T.G. Langdon, Microstructural Evolution in an Al-6061 Alloy Processed by High-Pressure Torsion, Mater. Sci. Eng. A, 2010, 527, p 4864–4869.

11.

G. Faraji and P. Asadi, Characterization of AZ91/Alumina Nanocomposite Produced by FSP, Mater. Sci. Eng. A, 2011, 528, p 2431–2440.CrossRef

12.

G. Faraji, O. Dastani, and S.A.A. Akbari Mousavi, Effect of Process Parameters on Microstructure and Micro-hardness of AZ91/Al2O3 Surface Composite Produced by FSP, Mater. Eng. Perform. doi:10.1007/s11665-010-9812-0.

13.

J.K. Kim, H.G. Jeong, S.I. Hong, Y.S. Kim, and W.J. Kim, Effect of Aging Treatment on Heavily Deformed Microstructure of a 6061 Aluminum Alloy After Equal Channel Angular Pressing, Scr. Mater., 2001, 45, p 901–907.CrossRef

14.

Z. Horita, T. Fujinami, M. Nemoto, and T.G. Langdon, Improvement of Mechanical Properties for Al Alloys Using Equal-Channel Angular Pressing, J. Mater. Process. Technol., 2001, 117, p 288–292.CrossRef

15.

Y.H. Kim and J.H. Park, Upper Bound Analysis of Torsional Backward Extrusion Process, Mater. Process. Technol., 2003, 143–144, p 735–740.CrossRef

16.

C. Kennedy and L.E. Murr, Comparison of Tungsten Heavy-Alloy Rod Penetration into Ductile and Hard Metal Targets: Microstructural Analysis and Computer Simulations, Mater. Sci. Eng. A, 2002, 325, p 131–143.CrossRef

17.

K. Dehghani, M. Salehi, M. Salehi, and H. Aboutalebi, Comparing the Melt-Spun Nanostructured Aluminum 6061 Foils with Conventional Direct Chill Ingot, Mater. Sci. Eng., 2008, A489, p 245–252.

18.

M. Salehi and K. Dehghani, Structure and Properties of Nanostructured Aluminum A413.1 Produced by Melt Spinning Compared with Ingot Microstructure, J. Alloys Compd., 2008, 457, p 357–361.CrossRef

19.

S.M. Fatemi-Varzaneh and A. Zarei-Hanzaki, Processing of AZ31 Magnesium Alloy by a New Noble Severe Plastic Deformation Method, Mater. Sci. Eng. A, 2009, 504, p 104–106.CrossRef

20.

G. Faraji, M.M. Mashhadi, and H.S. Kim, Microstructure Inhomogeneity in Ultra-Fine Grained Bulk AZ91 Produced by Accumulative Back Extrusion (ABE), Mater. Sci. Eng. A, 2011, 528, p 4312–4317

21.

G. Faraji, M.M. Mashhadi, and H.S. Kim, Microstructural Evolution of UFG Magnesium Alloy Produced by Accumulative Back Extrusion (ABE), Mater. Manuf. Proc., 2011, doi:10.1080/10426914.2011.577880

22.

A. Roostaei, A. Zarei-Hanzaki, M.H. Parsa, and S.M. Fatemi-Varzaneh, An Analysis to Plastic Deformation Behavior of AZ31 Alloys During Accumulative Roll Bonding Process, J. Mater. Sci., 2010, 45, p 4494–4500.CrossRef

23.

A. Yazdipour, A. Shafiei, and K. Dehghani, Modeling the Microstructural Evolution and Effect of Cooling Rate on the Nanograins Formed During the Friction Stir Processing of Al508, Mater. Sci. Eng., 2009, 527, p 192–197.CrossRef

24.

Y. Fukuda, K. Oh-ishi, M. Furukawa, Z. Horita, and T.G. Langdon, Influence of Crystal Orientation on ECAP of Aluminum Single Crystals, Mater. Sci. Eng. A, 2006, 420, p 79–86.CrossRef

25.

N. Tsuji, Y. Saito, S.H. Lee, and Y. Minamino, ARB (Accumulative Roll-Bonding) and Other New Techniques to Produce Bulk Ultrafine Grained Materials, Adv. Eng. Mater., 2003, 5, p 338–344.CrossRef

26.

X. Huang, N. Kamikawa, and N. Hansen, Strengthening Mechanisms in Nanostructured Aluminum, Mater. Sci. Eng. A, 2008, 483–484, p 102–104.

27.

M.R. Shankar et al., Microstructure and Stability of Nanocrystalline Aluminum 6061 Created by Large Strain Machining, Acta Mater., 2005, 53, p 4781–4793.CrossRef

28.

M.M. Moshksar and R. Ebrahimi, A New Upper Bound Analysis for Prediction of Load and Flow Pattern in Backward Extrusion Forging, Iran. J. Sci. Technol. Trans. B, 1999, 23, p 251–253.

29.

M.M. Moshksar and R. Ebrahimi, An Analytical Approach for Backward-Extrusion Forging of Regular Polygonal Hollow Components, Int. J. Mech. Sci., 1998, 40, p 1247–1263.CrossRef

Titel: Producing Ultrafine Grain Al6061 Alloy by Accumulative Back Extrusion Process
verfasst von: H. Alihosseini
G. Faraji
K. Dehghani
Publikationsdatum: 01.07.2012
Verlag: Springer US
Erschienen in: Journal of Materials Engineering and Performance / Ausgabe 7/2012
Print ISSN: 1059-9495
Elektronische ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-011-0026-x

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 7/2012

Optimization of Friction Welding of Tube-to-Tube Plate Using an External Tool with Filler Plate

Removal of Double Oxide Film Defects by Ceramic Foam Filters

Effect of Water Cooling on the Performances of Friction Stir Welding Heat-Affected Zone

Evaluation of the Fatigue Life of High-Strength Low-Alloy Steel Girth Welds in Aqueous Saline Environments with Varying Carbon Dioxide Partial Pressures

Microscopic Mechanism of Strengthening Under Low-Amplitude Loads Below the Fatigue Limit

Performance Evaluation of a Commercial Polyurethane Coating in Marine Environment

Premium Partner

Marktübersichten