nach oben

Erschienen in:

2019 | OriginalPaper | Buchkapitel

SPH Modeling and Experimental Study of Unidirectional Fiber-Reinforced Composite Cutting

verfasst von : I. A. Shchurov, A. V. Nikonov

Erschienen in: Proceedings of the 4th International Conference on Industrial Engineering

Verlag: Springer International Publishing

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

At present, unidirectional fiber-reinforced composites (UD-FRC) are widely used. The machining of UD-FRC workpieces has some characteristic features. Thus, homogeneous materials cutting experience may not be used directly. One of the problems of UD-FRC machining is interfacial debonding between fibers and matrix at cutting wedge punching-in which results in surface quality deterioration. Therefore, prediction of the obtained surface quality is a vital problem. A rational selection of tool geometry results in debonding reduction. It is reasonable to apply numerical calculations methods as a pilot research stage. In the present research, the results of an SPH method modeling of UD-FRC workpiece machining are given. For the verification of the obtained results, experimental studies have been conducted. A qualitative agreement of modeling and experimental results proves that SPH method application is expedient for UD-FRC workpiece machining modeling.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Vorheriges Kapitel Improved Axis Determination Method for Calculation of Virtual Pitch Thread Diameter Using a Point Cloud from CMM

Nächstes Kapitel Strengthening of Low-Alloyed Steels by Carbides During Carbon-Black-Gas Carburizer Cementation

Hocheng H (2012) Machining technology for composite materials. Principles and practice. Woodhead Publishing Limited, Cambridge, p 472CrossRef

Zemann R, Sacherl J, Hake W, Bleicher F (2014) New measurement processes to define the quality of machined fibre reinforced polymers. Proc Eng 100:636–645CrossRef

Liu H, Xie W, Sun Y, Zhang J, Chen N (2017) Investigations on micro-cutting mechanism and surface quality of carbon fiber-reinforced plastic composites. Int J Adv Manuf Technol 1–10. https://doi.org/10.1007/s00170-017-1110-7CrossRef

Abena A, Soo SL, Essa K (2017) Modelling the orthogonal cutting of UD-CFRP composites: development of a novel cohesive zone model. Compos Struct 168:65–83. https://doi.org/10.1016/j.compstruct.2017.02.030CrossRef

Limido J, Espinosa C, Salaün M, Mabru C, Chieragatti R (2009) High speed machining modelling: SPH method capabilities. In: 4th smoothed particle hydrodynamics european research interest community (SPHERIC) workshop, Nantes, 27–29 May 2009

Bagci E (2011) 3-D numerical analysis of orthogonal cutting process via mesh-free method. Int J Phys Sci 6(6):1267–1282

Parle D, Singh RK, Joshi SS (2014) Modeling of specific cutting energy in micro-cutting using SPH simulation. In: IWMF2014, 9th international workshop on microfactories, pp 121–126

Takabi B, Tajdari M, Tai LB (2017) Numerical study of smoothed particle hydrodynamics method in orthogonal cutting simulations—Effects of damage criteria and particle density. J Manuf Process 30:523–531. https://doi.org/10.1016/j.jmapro.2017.10.020CrossRef

Schwer LE (2009) Aluminium plate perforation: a comparative case study using Lagrange with erosion. In: Proceeding of multi-material ALE, and smooth particle hydrodynamics, 7-th European LS-DYNA conference, 28

10.

Corbett BM (2006) Numerical simulations of target hole diameters for hypervelocity impacts into elevated and room temperature bumpers. Int J Impact Eng 33:431–440. https://doi.org/10.1016/j.ijimpeng.2006.09.086CrossRef

11.

Arola D, Ramulu M (1997) Orthogonal cutting of fiber-reinforced composites: a finite element analysis. Int J Mech Sci 5:597–613. https://doi.org/10.1016/S0020-7403(96)00061-6CrossRefMATH

12.

Rao GVG, Mahajan P, Bhatnagar N (2008) Three-dimensional macro-mechanical finite element unidirectional-fiber reinforced polymer composites. Mater Sci Eng, A 498:142–149CrossRef

13.

Turki Y, Habak M, Velasco R, Aboura Z, Khellil K, Vantomme P (2014) Experimental investigation of drilling damage and stitching effects on the mechanical behavior of carbon/epoxy composites. Int J Mach Tools Manuf 87:61–72. https://doi.org/10.1016/j.ijmachtools.2014.06.004CrossRef

14.

Eneyew ED, Mamidala R (2014) Experimental study of surface quality and damage when drilling unidirectional CFRP composites. J Mater Res Technol 3(4):354–362. https://doi.org/10.1016/j.jmrt.2014.10.003CrossRef

15.

Soussia AB (2014) Rigorous treatment of dry cutting of FRP—interface consumption concept: a review. Int J Mech Sci 83:1–29. https://doi.org/10.1016/j.ijmecsci.2014.03.017CrossRef

16.

Azmi AI (2013) Chip formation studies in machining fibre reinforced polymer composites. Int J Mater Prod Technol 46(1):32–46. https://doi.org/10.1016/j.procir.2014.03.013CrossRef

17.

Li H, Qin X, He G, Jin Y, Sun D, Price M (2016) Investigation of chip formation and fracture toughness in orthogonal cutting of UD-CFRP. Int J Adv Manuf Technol 82:1079–1088. https://doi.org/10.1007/s00170-015-7471-xCrossRef

18.

Su Y, Jia Z, Niu B, Bi G (2016) Size effect of depth of cut on chip formation mechanism in machining of CFRP. Compos Struct 164:316–327. https://doi.org/10.1016/j.compstruct.2016.11.044CrossRef

19.

Voß R, Henerichs M, Kuster F, Wegener K (2014) Chip root analysis after machining carbon fiber reinforced plastics (CFRP) at different fiber orientations. Proc CIRP 14:217–222. https://doi.org/10.1016/j.procir.2014.03.013CrossRef

20.

Sang-Ook A, Lee Eun-Sang, Sang-Lai N (1995) A study on the cutting characteristics of glass fiber reinforced plastics with respect to tool materials and geometries. J Mater Process Technol 68(1):60–67. https://doi.org/10.1016/S0924-0136(96)02534-4CrossRef

Titel: SPH Modeling and Experimental Study of Unidirectional Fiber-Reinforced Composite Cutting
verfasst von: I. A. Shchurov
A. V. Nikonov
Verlag: Springer International Publishing
Buch: Proceedings of the 4th International Conference on Industrial Engineering
Print ISBN: 978-3-319-95629-9

Electronic ISBN: 978-3-319-95630-5

Copyright-Jahr: 2019
DOI: https://doi.org/10.1007/978-3-319-95630-5_174

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht