nach oben

The International Journal of Advanced Manufacturing Technology

Erschienen in:

16.02.2024 | ORIGINAL ARTICLE

A challenging study on compatibility or incompatibility of vegetable-based lubricant with human health

verfasst von: Seyed Hasan Musavi, Behnam Davoodi

Erschienen in: The International Journal of Advanced Manufacturing Technology | Ausgabe 7-8/2024

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

It has been estimated that over 85% of the cutting fluid used in machining industries is mineral-based which are potentially carcinogenic that over 70% of cutting fluid waste releases to the nature without any purification process. Knowing environmental concerns and increasing regulations over pollution, the request to use risk-free lubricant is irrefutable. Recently, many scholars recommended vegetable-based cutting fluid (VBCF) for replacing with mineral-based one (MBCF). The present work has tried to study the compatibility or incompatibility of VBCF with human health and provide a method for eliminating or reducing their potential risks. To achieve this goal, a study on one of the most known, destructive, and accessible microbes (Pseudomonas) in the workshop environment was performed. The results showed that Pseudomonas could multiply in solid and liquid mediums, and its colonies could quickly propagate in VBCF. Therefore, as a significant achievement in this study, unreinforced VBCF is not a suitable selection from a health point of view. Although these cutting fluids are introduced as a compatible lubricant with humans and the environment, bacteria and mold can multiply swiftly without apparent alterations. It was also observed that using nanoparticles like copper oxide (CuO) with a specific volume fraction (0.4%) could fight with the biofilm of Pseudomonas to destroy the colonies at the initial time of their formation, while silicon-oxide nanoparticles had no effect on control of microbial growth. Therefore, CuO-nanoparticles present antibacterial characteristics when they interact with microbes. As a result, CuO-nanoparticles are the good choice for replacing with harmful additive like formaldehyde biocides in MBCF. Scanning electron microscope (SEM) images and energy-dispersive X-ray spectroscopy (EDX) analysis also studied the machinability attributes. The machining tests indicated that the VBCF reinforced with 0.4 wt% of CuO-nanoparticles also greatly impacts the control of tool wear mechanisms, especially products of adhesion wear like built-up edge and built-up layer, and surface quality compared to the conventional cutting fluid during the A286 superalloy machining.

Vorheriger Artikel Unveiling empirical correlation between electrical and thermal conductivities of medium porosity open-cell porous aluminium fabricated by replication casting method

Nächster Artikel Reducing tool-tip wear in micro-ECDM scanning process with feedback control of flexible contact force

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

In biology, a pathogen is anything that can create illness.

Amino acid is an organic mixture, which includes amine(-NH₂) and carboxyl(-COOH) functional groups. Its main agents consist of N, O, H, and C.

Endocytosis introduces as a cellular function that materials are entered to the cell.

Khan MA, Jaffery SH, Khan M, Alruqi M (2023) Investigation into the machinability of Ti-6Al-4V under cryogenic condition. J Market Res. https://doi.org/10.1016/j.jmrt.2023.06.022CrossRef

Bayat M, Adibi H, Barzegar A, Rezaei SM (2022) Experimental and numerical investigation of heat generation and surface integrity of ZrO2 bioceramics in grinding process under MQL condition. J Mech Behav Biomed Mater 131:105226CrossRef

Li B, Zhang X, Zhang S (2021) Microstructure investigation of dynamic recrystallization in hard machining: from thermodynamic irreversibility perspective. Front Mech Eng 16:315–330CrossRef

Hatami O, Adibi H, Rezaei SM (2022) Evaluation of the grinding process utilizing an auxiliary compressed air jet on cleaning the grinding wheel surface. Proc Inst Mech Eng Part E: J Process Mech Eng. https://doi.org/10.1177/09544089221109835CrossRef

Musavi SH, Davoodi B, Eskandari B (2020) Evaluation of surface roughness and optimization of cutting parameters in turning of AA2024 alloy under different cooling-lubrication conditions using RSM method. J Cent South Univ 27(6):1714–1728CrossRef

Gajrani K, Suvin P, Kailas S (2021) Machining of hard materials using textured tool with minimum quantity nano-green cutting fluid. CIRP J Manuf Sci Technol 35:410–421. https://doi.org/10.1016/j.cirpj.2021.06.018CrossRef

Zhang X, Li Ch, Zhou Z et al (2023) Vegetable oil-based nanolubricants in machining: from physicochemical properties to application. Chin J Mech Eng 36:76. https://doi.org/10.1186/s10033-023-00895-5CrossRef

Chetan Ghosh S, Rao PV (2015) Application of sustainable techniques in metal cutting for enhanced machinability: a review. J Clean Prod 100(1):17–34CrossRef

Sankaranarayanan R, Rajesh Jesudoss Hynes N, Senthil Kumar J, Krolczyk GM (2021) A comprehensive review on research developments of vegetable-oil based cutting fluids for sustainable machining challenges. J Manuf Process 67:286–313. https://doi.org/10.1016/j.jmapro.2021.05.002CrossRef

10.

Musavi SH, Davoodi B, Niknam SA (2019) Effects of reinforced nanoparticles with surfactant on surface quality and chip formation morphology in MQL-turning of superalloys. J Manuf Process 40:128–139CrossRef

11.

Liu M, Li Ch, Yang M et al (2023) Mechanism and enhanced grindability of cryogenic air combined with biolubricant grinding titanium alloy. Tribol Int 187:108704. https://doi.org/10.1016/j.triboint.2023.108704CrossRef

12.

Farooq MU, Anwar S, Ullah R, Guerra RH (2023) Sustainable machining of additive manufactured SS-316L underpinning low carbon manufacturing goal. J Market Res 24:2299–2318. https://doi.org/10.1016/j.jmrt.2023.03.122CrossRef

13.

Liu M, Li C, Zhang Y et al (2021) Cryogenic minimum quantity lubrication machining: from mechanism to application. Front Mech Eng 16:649–697. https://doi.org/10.1007/s11465-021-0654-2CrossRef

14.

Musavi SH, Davoodi B (2021) Risk assessment for hazardous lubricants in machining industry. Environ Sci Pollut Res 28(1):625–634CrossRef

15.

International Agency for Research on Cancer (IARC) (1987) Mineral oils (lubricant-based oils and derived products). IARC Sci Publ 33(2):87–168

16.

Park RM (2018) Risk assessment for metalworking fluids and cancer outcomes. Am J Ind Med 61(3):198–203CrossRef

17.

Hong ShY, Broomer M (2000) Economical and ecological cryogenic machining of AISI 304 austenitic stainless steel. Clean Technol Environ Policy 2:157–166

18.

Tolbert PE, Eisen EA, Pothier LJ, Monson RR, Hallock MF, Smith TJ (1992) Mortality studies of machining-fluid exposure in the automobile industry, II. Risks associated with specific fluid types. Scand J Work Environ Health 18:351–360CrossRef

19.

Danish M, Gupta M, Rubaiee S (2021) Influence of hybrid Cryo-MQL lubri-cooling strategy on the machining and tribological characteristics of Inconel 718. Tribol Int 163:107178. https://doi.org/10.1016/j.triboint.2021.107178CrossRef

20.

Kim D, Kim H, Park H (2021) Tool wear, economic costs, and CO2 emissions analysis in cryogenic assisted hard-turning process of AISI 52100 steel. Sustain Mater Technol 30:e00349. https://doi.org/10.1016/j.susmat.2021.e00349

21.

Halim N, Haron Ch, Ghani J (2022) PVD multi-coated carbide milling inserts performance: comparison between cryogenic and dry cutting conditions. J Manuf Process 73:895–902. https://doi.org/10.1016/j.jmapro.2021.11.033CrossRef

22.

Zhao J, Liu Zh (2020) Influences of coating thickness on cutting temperature for dry hard turning Inconel 718 with PVD TiAlN coated carbide tools in initial tool wear stage. J Manuf Process 56(A):1155–1165. https://doi.org/10.1016/j.jmapro.2020.06.010CrossRef

23.

Zhang Y, Li Ch, Jia D, Zhang D, Zhang X (2015) Experimental evaluation of MoS₂ nanoparticles in jet MQL grinding with different types of vegetable oil as base oil. J Clean Prod 87:930–940CrossRef

24.

Xu W, Li Ch, Zhang Y et al (2022) Electrostatic atomization minimum quantity lubrication machining: from mechanism to application. Int J Extrem Manuf 4:042003. https://doi.org/10.1088/2631-7990/ac9652CrossRef

25.

Dixit US, Sarma D, Davim JP (2012) Environmentally friendly machining. Springer Science & Business Media

26.

Goindi GS, Sarkar P (2017) Dry machining: a step towards sustainable machining-challenges and future directions. J Clean Prod 165:1557–1571. https://doi.org/10.1016/j.jclepro.2017.07.235CrossRef

27.

Krolczyk GM, Maruda RW, Krolczyk JB et al (2019) Ecological trends in machining as a key factor in sustainable production: a review. J Clean Prod 218:601–615CrossRef

28.

Cui X, Li Ch, Yang M et al (2023) Enhanced grindability and mechanism in the magnetic traction nanolubricant grinding of Ti-6Al-4V. Tribol Int 186:108603. https://doi.org/10.1016/j.triboint.2023.108603CrossRef

29.

Musavi SH, Davoodi B, Razfar MR (2023) Performance assessment of reinforced nanofluid with surface-active agent for machinability improvement. Int J Adv Manuf Technol 128:3983–4001CrossRef

30.

Bai X, Jiang J, Li Ch et al (2023) Tribological performance of different concentrations of Al2O3 nanofluids on minimum quantity lubrication milling. Chin J Mech Eng 36(1):11. https://doi.org/10.1186/s10033-022-00830-0CrossRef

31.

Duan Zh, Li Ch, Zhang Y et al (2023) Mechanical behavior and semiempirical force model of aerospace aluminum alloy milling using nano biological lubricant. Front Mech Eng 18(1):4. https://doi.org/10.1007/s11465-022-0720-4CrossRef

32.

Dambatta YS, Li Ch, Yang M et al (2023) Grinding with minimum quantity lubrication: a comparative assessment. Int J Adv Manuf Technol 128:955–1014. https://doi.org/10.1007/s00170-023-11962-5CrossRef

33.

Wang X, Song Y, Li Ch et al (2023) Nanofluids application in machining: a comprehensive review. Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-022-10767-2CrossRef

34.

Eltaggaz A, Ali Sh, Badwal K, Deiab I (2023) Influence of nanoparticle concentration in nanofluid MQL on cutting forces, tool wear, chip morphology when milling of Inconel 718. Int J Adv Manuf Technol 129:1787–1800CrossRef

35.

Oussama B, Yapan Y, Uysal A et al (2023) Assessment of turning AISI 316L stainless steel under MWCNT-reinforced nanofluid-assisted MQL and optimization of process parameters by NSGA-II and TOPSIS. Int J Adv Manuf Technol 127:3855–3868CrossRef

36.

Pal A, Chatha SS, Sidhu HS (2022) Assessing the lubrication performance of various vegetable oil-based nano-cutting fluids via eco-friendly MQL technique in drilling of AISI 321 stainless steel. J Braz Soc Mech Sci Eng 44:148. https://doi.org/10.1007/s40430-022-03442-wCrossRef

37.

Pal A, Chatha S, Sidhu H (2021) Performance evaluation of the minimum quantity lubrication with Al2O3- mixed vegetable-oil-based cutting fluid in drilling of AISI 321 stainless steel. J Manuf Process 66:238–249. https://doi.org/10.1016/j.jmapro.2021.04.024CrossRef

38.

Kumar P, Ravi S (2021) Investigation on effects of vegetable-based cutting fluids in turning operation of EN 24 Steel. Mater Today: Proc 39(1):95–99. https://doi.org/10.1016/j.matpr.2020.06.315CrossRef

39.

Ni J, Cui Zh, He L et al (2021) Reinforced lubrication of vegetable oils with nano-particle additives in broaching. J Manuf Process 70:518–528. https://doi.org/10.1016/j.jmapro.2021.09.005CrossRef

40.

Saleem M, Mehmood A (2022) Eco-friendly precision turning of superalloy Inconel 718 using MQL based vegetable oils: tool wear and surface integrity evaluation. J Manuf Process 73:112–127. https://doi.org/10.1016/j.jmapro.2021.10.059CrossRef

41.

Sani S, Rahim E, Sharif S, Sasahara H (2019) The influence of modified vegetable oils on tool failure mode and wear mechanisms when turning AISI 1045. Tribol Int 129:347–362CrossRef

42.

Gajrani KK, Ram D, Sankar MR (2017) Biodegradation and hard machining performance comparison of eco-friendly cutting fluid and mineral oil using flood cooling and minimum quantity cutting fluid techniques. J Clean Prod 165:1420–1435CrossRef

43.

Musavi SH, Davoodi B, Niknam SA (2018) Environmental-friendly turning of A286 superalloy. J Manuf Process 32:734–743CrossRef

44.

Agrawal SM, Patil N (2018) Experimental study of non-edible vegetable oil as a cutting fluid in machining M2 Steel using MQL. Procedia Manuf 20:207–212CrossRef

45.

Thottackkad M, Perikinalil R, Kumarapillai P (2012) Experimental evaluation on the tribological properties of coconut oil by the addition of CuO nanoparticles. Int J Precis Eng Manuf 13:111–116CrossRef

46.

Das A, Patel S, Das S (2019) Performance comparison of vegetable oil-based nanofluids towards machinability improvement in hard turning of HSLA steel using minimum quantity lubrication. Mech Ind 20:506526. https://doi.org/10.1051/meca/2019036CrossRef

47.

Shabgard M, Seyedzavvar M, Mohammadpourfard M (2017) Experimental investigation into lubrication properties and mechanism of vegetable-based CuO nanofluid in MQL grinding. Int J Adv Manuf Technol 92:3807–3823CrossRef

48.

Sayuti M, Sarhan A, Salem F (2014) Novel uses of SiO₂ nano-lubrication system in hard turning process of hardened steel AISI4140 for less tool wear, surface roughness and oil consumption. J Clean Prod 67:265–276CrossRef

49.

Sharma AK, Tiwari AK, Dixit AR, Singh RK (2017) Investigation into performance of SiO₂ nanoparticle based cutting fluid in machining process. Mater Today: Proc 4:133–141

50.

Musavi SH, Davoodi B, Niknam SA (2019) Effects of reinforced nanofluid with nanoparticles on the cutting tool wear morphology. J Cent South Univ 26(5):1050–1064CrossRef

51.

Amin F, Khattak B, Alotaibi A et al (2021) green synthesis of copper oxide nanoparticles using Aerva javanica leaf extract and their characterization and investigation of in vitro antimicrobial potential and cytotoxic activities. Evid Based Complement Alternat Med. https://doi.org/10.1155/2021/5589703CrossRef

52.

Iliescu C, Poenar D, Selvan S (2010) Frequency dependence on the accuracy of electrical impedance spectroscopy measurements in microfluidic devices. J Micromech Microeng 20(2):022001. https://doi.org/10.1088/0960-1317/20/2/022001CrossRef

53.

Banar M, Emaneini M, Satarzadeh M et al (2016) Evaluation of mannosidase and trypsin enzymes effects on biofilm production of Pseudomonas aeruginosa Isolated from burn wound infections. PLoS ONE 11(10):1–13. https://doi.org/10.1371/journal.pone.0164622CrossRef

54.

Soroush S, Jabalameli F, Taherikalani M et al (2016) Investigation of biofilm formation ability, antimicrobial resistance and the staphylococcal cassette chromosomes patterns of methicillin-resistant Staphylococcus epidermidis with different sequence types isolated from children. Microb Pathog 93:126–130CrossRef

55.

Musavi SH, Davoodi B, Niknam SA (2021) Eco-green machining of superalloy A286: assessment of tool wear morphology and surface topology. Proc Inst Mech Eng B: J Eng Manuf 235(9):1412–1424CrossRef

56.

Musavi SH, Sepehrikia M, Davoodi B (2022) Performance analysis of developed micro-textured cutting tool in machining aluminum alloy 7075–T6: assessment of tool wear and surface roughness. Int J Adv Manuf Technol 119(5):3343–3362CrossRef

57.

Asgari A, Delavar H, Sedighi M (2023) Microstructure and surface integrity of machined AZ91 magnesium alloy. J Market Res 22:735–746. https://doi.org/10.1016/j.jmrt.2022.11.164CrossRef

58.

Musavi SH, Davoodi B, Nankali M (2021) Assessment of tool wear and surface integrity in ductile cutting using a developed tool. Arab J Sci Eng 46:7773–7787CrossRef

59.

Liu M, Li Ch, Zhang Y et al (2023) Analysis of grinding mechanics and improved grinding force model based on randomized grain geometric characteristics. Chin J Aeronaut 36(7):160–193. https://doi.org/10.1016/j.cja.2022.11.005CrossRef

60.

Sharma AK, Tiwari AK, Dixit AR, Singh RK (2018) Novel uses of alumina/graphene hybrid nanoparticle additives for improved tribological properties of lubricant in turning operation. Tribol Int 119:99–111CrossRef

61.

Khodaii J, Adibi H, Barazandeh F et al (2020) Improvement of surface integrity in the grinding of bioceramic partially stabilized zirconia using analytical, numerical, and experimental methods. Ceram Int 46(9):13784–13797CrossRef

62.

Khodaii J, Adibi H, Barazandeh F et al (2021) Investigation of the surface integrity, flexural strength on the grinding of alumina for biomedical applications. Precis Eng 67:110–122CrossRef

63.

Esmaeili H, Adibi H, Rezaei SM (2021) Study on surface integrity and material removal mechanism in eco-friendly grinding of Inconel 718 using numerical and experimental investigations. Int J Adv Manuf Technol 112:1797–1818CrossRef

64.

Hatami O, Adibi H, Rezaei SM (2022) Application of a compressed air jet for cleaning of wheel surface in grinding nickel-based super alloy Inconel 718. CIRP J Manuf Sci Technol 37:233–244CrossRef

65.

Musavi SH, Razfar MR, Domiri GD (2023) Evaluation of the influence of surface structure on tribological properties of the solid–liquid interface: analytical and experimental assessment. J Mol Liq 390:122967CrossRef

Titel: A challenging study on compatibility or incompatibility of vegetable-based lubricant with human health
verfasst von: Seyed Hasan Musavi
Behnam Davoodi
Publikationsdatum: 16.02.2024
Verlag: Springer London
Erschienen in: The International Journal of Advanced Manufacturing Technology / Ausgabe 7-8/2024
Print ISSN: 0268-3768
Elektronische ISSN: 1433-3015
DOI: https://doi.org/10.1007/s00170-024-13083-z

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 7-8/2024

Effect of short electric arc milling discharge machining on the processing performance of two-dimensional C/SiC composites

Announcement of B. John Davies Prize for the best paper published in IJAMT in 2022

A novel assembly-oriented measurement datum transformation and tolerance reallocation method

Correction to: Closed-loop quality control system for laser chemical machining in metal micro-production

A novel approach to voice of customer extraction using GPT-3.5 Turbo: linking advanced NLP and Lean Six Sigma 4.0

Numerical analysis on temperature characteristics and melt flow dynamic behaviors in electron beam welding of dissimilar aluminum alloy lock-butt joint

Premium Partner

Marktübersichten