nach oben

The International Journal of Advanced Manufacturing Technology

Erschienen in:

07.04.2022 | ORIGINAL ARTICLE

Effects of voids and raster orientations on fatigue life of notched additively manufactured PLA components

verfasst von: Soran Hassanifard, Kamran Behdinan

Erschienen in: The International Journal of Advanced Manufacturing Technology | Ausgabe 9-10/2022

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

In this study, the fatigue life of notched polylactic acid (PLA) samples fabricated through the fused deposition modeling (FDM) technique was studied experimentally and numerically. The volumetric method based on the theory of critical distance was employed for fatigue life predictions. The effects of influential process parameters including raster orientation and FDM-induced defects such as voids or gaps inside the parts were examined on the fatigue strength reduction factors and fatigue lives. Circular and elliptical-shaped notch geometries were considered with various dimensions. Fatigue tests were conducted on notched and un-notched samples at the load ratio of 0.1. Predicted results were compared with experimental fatigue test data. Results revealed that the raster orientation parameter had a substantial impact on fatigue strength reduction factors and fatigue lives. The stress concentrations induced by the FDM process on the surfaces and inside the parts for the samples with 90° raster angles acted similar to the sharp notches, resulting in no substantial difference in fatigue life of notched and un-notched 3D-printed samples. In contrast, un-notched 3D-printed specimens with 0° raster orientations possessed higher fatigue lives as compared to the notched samples. While the volumetric approach efficiently predicted the fatigue lives of the samples with 90° raster orientations, it moderately underpredicted the fatigue lives of the samples with 0° raster angles.

Vorheriger Artikel Multi-objective modelling and optimal parameter selection of a multi-pass milling process considering uncertain milling stability constraint

Nächster Artikel Surface flatness and roughness of diamond wire electrical discharge sawing mono-crystalline silicon with improved bath cooling

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Low ZX et al (2017) Perspective on 3D printing of separation membranes and comparison to related unconventional fabrication techniques. J Membr Sci 523:596–613. https://doi.org/10.1016/j.memsci.2016.10.006CrossRef

Larraza I et al (2021) Cellulose and graphene based polyurethane nanocomposites for FDM 3D printing: filament properties and printability. Polymers 13(839). https://doi.org/10.3390/polym13050839

Dizon JRC et al (2018) Mechanical characterization of 3D-printed polymers. Additive Manufacturing 20:44–67. https://doi.org/10.1016/j.addma.2017.12.002

Zhao L et al (2021) Development model and experimental characterization of residual stress of 3D printing PLA parts with porous structure. Appl Phys A 127(98). https://doi.org/10.1007/s00339-020-04238-2

Hernandez-Contreras A et al (2020) Extended CT void analysis in FDM additive manufacturing components. Materials 13(3831). https://doi.org/10.3390/ma13173831

Wang J et al (2016) A novel approach to improve mechanical properties of parts fabricated by fused deposition modeling. Mater Des 105:152–159. https://doi.org/10.1016/j.matdes.2016.05.078CrossRef

Tronvoll SA, Welo T, Elverum C (2018) The effects of voids on structural properties of fused deposition modelled parts: a probabilistic approach. Int J Adv Manuf Technol 97:3607–3618. https://doi.org/10.1007/s00170-018-2148-xCrossRef

Fayazbakhsh K, Movahedi M, Kalman J (2019) The impact of defects on tensile properties of 3D printed parts manufactured by fused filament fabrication. Mater Today Commun 18:140–148. https://doi.org/10.1016/j.mtcomm.2018.12.003CrossRef

Kerekes TW et al (2019) Characterization of process–deformation/damage property relationship of fused deposition modeling (FDM) 3D-printed specimens. Addit Manuf 25:532–544. https://doi.org/10.1016/j.addma.2018.11.008CrossRef

10.

Fischer M, Schoppner V (2017) Fatigue behavior of FDM parts manufactured with Ultem 9085. J Miner Metals Mater Soc 69(3):563–568. https://doi.org/10.1007/s11837-016-2197-2CrossRef

11.

Ezeh OH, Susmel L (2019) Fatigue strength of additively manufactured polylactide (PLA): effect of raster angle and non-zero mean stresses. Int J Fatigue 126:319–326. https://doi.org/10.1016/j.ijfatigue.2019.05.014CrossRef

12.

Ziemian S, Okwara M, Ziemian C (2015) Tensile and fatigue behavior of layered acrylonitrile butadiene styrene. Rapid Prototyp J 21(3):270–278. https://doi.org/10.1108/RPJ-09-2013-0086CrossRef

13.

Afrose MF et al (2016) Effects of part build orientations on fatigue behaviour of FDM-processed PLA material. Prog Addit Manuf 1:21–28. https://doi.org/10.1007/s40964-015-0002-3CrossRef

14.

Brenne F, Niendorf T (2019) Effect of notches on the deformation behavior and damage evolution of additively manufactured 316L specimens under uniaxial quasi-static and cyclic loading. Int J Fatigue 127:175–189. https://doi.org/10.1016/j.ijfatigue.2019.05.018CrossRef

15.

Nicoletto G et al (2020) Influence of layer-wise fabrication and surface orientation on the notch fatigue behavior of as-built additively manufactured Ti6Al4V. Int J Fatigue 134:1–10. https://doi.org/10.1016/j.ijfatigue.2020.105483CrossRef

16.

Chan KS, Peralta-Duran A (2019) A methodology for predicting surface crack nucleation in additively manufactured metallic components. Metall Mater Trans A 50A:4378–4387. https://doi.org/10.1007/s11661-019-05309-7CrossRef

17.

Kahlin M, Ansell H, Moverare JJ (2017) Fatigue behaviour of notched additive manufactured Ti6Al4V with as-built surfaces. Int J Fatigue 101:51–60. https://doi.org/10.1016/j.ijfatigue.2017.04.009CrossRef

18.

Nicoletto G (2018) Directional and notch effects on the fatigue behavior of as-built DMLS Ti6Al4V. Int J Fatigue 106:124–131. https://doi.org/10.1016/j.ijfatigue.2017.10.004CrossRef

19.

Ahmed AA, Susmel L (2018) A material length scale–based methodology to assess static strength of notched additively manufactured polylactide (PLA). Fatigue Fract Eng Mater Struct 41:2071–2098. https://doi.org/10.1111/ffe.12746CrossRef

20.

Ahmed AA, Susmel L (2019) Static assessment of plain/notched polylactide (PLA) 3D-printed with different infill levels: equivalent homogenised material concept and Theory of Critical Distances. Fatigue Fract Eng Mater Struct 42:883–904. https://doi.org/10.1111/ffe.12958CrossRef

21.

Ng CT, Susmel L (2020) Notch static strength of additively manufactured acrylonitrile butadiene styrene (ABS). Addit Manuf 34:1–15. https://doi.org/10.1016/j.addma.2020.101212CrossRef

22.

Ezeh OH, Susmel L (2020) On the notch fatigue strength of additively manufactured polylactide (PLA). Int J Fatigue 136:1–12. https://doi.org/10.1016/j.ijfatigue.2020.105583CrossRef

23.

Solberg K, Wan D, Berto F (2020) Fatigue assessment of as-built and heat-treated Inconel 718 specimens produced by additive manufacturing including notch effects. Fatigue Fract Eng Mater Struct 43:2326–2336. https://doi.org/10.1111/ffe.13300CrossRef

24.

Solberg K, Berto F (2020) A diagram for capturing and predicting failure locations in notch geometries produced by additive manufacturing. Int J Fatigue 134:1–6. https://doi.org/10.1016/j.ijfatigue.2019.105428CrossRef

25.

Molaei R, Fatemi A (2021) Fatigue performance of additive manufactured metals under variable amplitude service loading conditions including multiaxial stresses and notch effects: experiments and modelling. Int J Fatigue 145:1–15. https://doi.org/10.1016/j.ijfatigue.2020.106002CrossRef

26.

Papon EA, Haque A (2018) Tensile properties, void contents, dispersion and fracture behaviour of 3D printed carbon nanofiber reinforced composites. J Reinf Plast Compos 37(6):381–395. https://doi.org/10.1177/0731684417750477CrossRef

27.

Francis V, Jain P (2016) Experimental investigations on fused deposition modelling of polymer-layered silicate nanocomposite. Virtual and Phys Prototyp 11(2):109–121. https://doi.org/10.1080/17452759.2016.1172431CrossRef

28.

Dowling NE (2003) Mechanical behavior of materials, engineering methods for deformation, fracture, and fatigue, 4th edn. Angshuman Chakraborty

29.

Smith KN, Watson P, Topper T (1970) A stress strain function for the fatigue of metals. J Eng Mater Technol 5(4):767–778

30.

Hassanifard S, Hashemi SM (2020) On the strain-life fatigue parameters of additive manufactured plastic materials through fused filament fabrication process. Addit Manuf 32:100973. https://doi.org/10.1016/j.addma.2019.100973CrossRef

31.

Neuber H (1961) Translation theory of notch stresses, principles for exact stress calculations. 1958, US Office of Technical Services, Springer, Washington, DC

32.

Peterson RE (1959) Notch sensitivity. In: Sines G, Waisman JL (eds) Metal Fatigue, pp 293–306

33.

Tanaka K (1983) Engineering formulae for fatigue strength reduction due to crack-like notches. Int J Fract 22:R39–R45. https://doi.org/10.1007/BF00942722CrossRef

34.

Taylor D (1999) Geometrical effects in fatigue: a unifying theoretical model. Int J Fatigue 21:413–420. https://doi.org/10.1016/S0142-1123(99)00007-9CrossRef

35.

Pluvinage G (2004) Fracture and fatigue emanating from stress concentrators. Kluwer Academic Publishers

36.

Averett RD et al (2011) The mechanical behavior of poly(lacticacid) unreinforced and nanocomposite films subjected to monotonic and fatigue loading conditions. J Compos Mater 45(26):2717–2726. https://doi.org/10.1177/0021998311410464CrossRef

Titel: Effects of voids and raster orientations on fatigue life of notched additively manufactured PLA components
verfasst von: Soran Hassanifard
Kamran Behdinan
Publikationsdatum: 07.04.2022
Verlag: Springer London
Erschienen in: The International Journal of Advanced Manufacturing Technology / Ausgabe 9-10/2022
Print ISSN: 0268-3768
Elektronische ISSN: 1433-3015
DOI: https://doi.org/10.1007/s00170-022-09169-1

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 9-10/2022

Analytical modelling of side grinding of orthogonal laminated SiCf/SiC composites based on effective elastic properties

The influence of powder size on the microstructure and properties of Mo2FeB2 coating fabricated via laser cladding with pre-placed powder

Calculation and analysis of quasi-dynamic cutting force and specific cutting energy in micro-milling Ti6Al4V

Comparison of machine learning methods for automatic classification of porosities in powder-based additive manufactured metal parts

Coaxiality error analysis and optimization of cylindrical parts of CNC turning process

Thermohydrodynamic lubrication-based friction mechanism modeling and integrated simulation of dynamic coordination for squeeze casting processes

Premium Partner

Marktübersichten