nach oben

Journal of Materials Engineering and Performance

Erschienen in:

28.06.2016

Fabrication of TiC-Reinforced Composites by Vacuum Arc Melting: TiC Mode of Reprecipitation in Different Molten Metals and Alloys

verfasst von: A. E. Karantzalis, Z. Arni, K. Tsirka, A. Evangelou, A. Lekatou, V. Dracopoulos

Erschienen in: Journal of Materials Engineering and Performance | Ausgabe 8/2016

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

TiC crystals were developed and grown through a melt dissolution and reprecipitation mechanism, in different alloy matrices (pure Fe, 316L, Fe-22 at.%Al, Ni-25at.%Al, and pure Co) through the use of Vacuum Arc Melting (VAM) process. The TiC surfaces exhibit a characteristic faceted mode of growth which is explained in terms of classic nucleation and crystal growth theories and is related with the well-known Jackson factor of crystal growth. Different morphologies of the finally solidified TiC grains are observed (dendritic, radially grown, isolated blocky crystals, particle clusters), the establishment of which may be most likely related with solidification progress, cooling rate, and melt compositional considerations. An initial, rough and qualitative phase identification shows a variety of compounds, and the attempts to define specific phase crystallographic-orientational relationships led to rather random results.

Vorheriger Artikel Tribological Behavior of Aluminum Alloy AlSi10Mg-TiB2 Composites Produced by Direct Metal Laser Sintering (DMLS)

Nächster Artikel The Influence of Al2O3 Powder Morphology on the Properties of Cu-Al2O3 Composites Designed for Functionally Graded Materials (FGM)

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Y. Chen and H.M. Wang, Growth Morphology and Mechanism of Primary TiC Carbide in Laser Clad TiC/FeAl Composite Coating, Mater. Lett., 2003, 57, p 1233–1238CrossRef

Y. Chen and H.M. Wang, Microstructure and Wear Resistance of Laser Clad TiC Reinforced FeAl Intermetallic Matrix Composite Coatings, Surf. Coat. Technol., 2003, 168, p 30–36CrossRef

T.Z. Kattamis and T. Suganuma, Solidification Processing and Tribological Behaviour of Particulate TiC-Ferrous Matrix Composites, Mater. Sci. Eng., A, 1990, 128, p 241–252CrossRef

Y. Chen and H.M. Wang, High Temperature Wear Resistance of a Laser Clad TiC Reinforced FeAl In Situ Composite Coating, Surf. Coat. Technol., 2004, 179, p 252–256CrossRef

Y. Chen and H.M. Wang, Eutectic MC Carbide Growth Morphologies of a Laser Clad TiC/FeAl Composite Coating, Mater. Lett., 2005, 59, p 3699–3702CrossRef

Y. Chen and H.M. Wang, Growth Morphologies and Mechanisms of Non-equilibrium Solidified MC Carbide, J. Mater. Res., 2006, 2, p 375–379CrossRef

A.E. Karantzalis, A. Lekatou, M. Georgatis, Z. Arni, and V. Dracopoulos, Solidification Observations of Vacuum Arc Melting Processed Fe-Al-TiC Composites: TiC Precipitation Mechanisms, Mater. Charact., 2011, 62, p 1196–1204CrossRef

N.S. Stoloff, C.T. Liu, and S.C. Deevi, Emerging Applications on Intermetallics, Intermetallics, 2000, 8, p 1313–1320CrossRef

F. Sheppe, P.R. Sahm, W. Hermann, U. Paul, and J. Preuhs, Nickel Aluminides: A Step Toward Industrial Application, Mater. Sci. Eng., 2002, A239–331, p 596–601CrossRef

10.

D.B. Miracle, Overview No 104: The Physical and Mechanical Properties of NiAl, Acta Metall. Mater., 1993, 41(3), p 649–684CrossRef

11.

V.K. Sikka, S.C. Deevi, S. Viswanathan, R.W. Swindeman, and M.L. Santella, Advances in Processing of Ni3Al-Based Intermetallics and Applications, Intermetallics, 2000, 8, p 1329–1337CrossRef

12.

Y. Chen and H.M. Wang, Laser Melted TiC Reinforced Nickel Aluminide Matrix In Situ Composites, J. Alloy. Compd., 2005, 391, p 49–54CrossRef

13.

Y. Chen and H.M. Wang, Microstructure and Wear Resistance of Laser-Melted TiC Reinforced Nickel Aluminide Dual-Phase Matrix In Situ Composite, Intermetallics, 2006, 14, p 325–331CrossRef

14.

A.E. Karantzalis, A. Lekatou, and K. Tsirka, Solidification Observations and Sliding Wear Behaviour of Vacuum Arc Melting Processed Ni-Al-TiC Composites, Mater. Charact., 2012, 69, p 97–107CrossRef

15.

Y.T. Pei and T.C. Zuo, Gradient Microstructure in Laser clad TiC-Reinforced Ni-Alloy Composite Coating, Mater. Sci. Eng. A, 1998, 241, p 259–263CrossRef

16.

L. Liu, F. Sommer, and H.Z. Fu, Effect of Solidification Conditions on MC Carbides in a Nickel-Base Superalloy in 738 LC, Scr. Metall. Mater., 1994, 30, p 587–591CrossRef

17.

D. Strzeciwilk, P. Tkacz, and Z. Wokulski, Transmission Electron Microscope Studies of TiC Crystals, Cryst. Res. Technol., 2000, 35, p 1295–1303CrossRef

18.

A.E. Karantzalis, A. Lekatou, and M. Evaggelidou, Microstructure and Sliding Wear Assessment of Co-TiC Composite Materials, Int. J. Cast Met. Res., 2014, 27(2), p 73–79CrossRef

19.

H.M. Wang, L.G. Yu, X.X. Li, and P. Jiang, Growth Morphology and Mechanism of MC Carbide Under Quasi-Rapid Solidification Conditions, Sci. Technol. Adv. Mater., 2001, 2, p 173–176CrossRef

20.

Y. Chen and H.M. Wang, Growth Morphologies and Mechanism of TiC in a Laser Surface Alloyed Coating on the Substrate of TiAl Intermetallics, J. Alloy. Compd., 2003, 351, p 304–308CrossRef

21.

Y. Chen and H.M. Wang, Rapidly Solidified MC Carbide Morphologies of a Pulsed Laser Surface Alloyed γ-TiAl Intermetallic with Carbon, Scripta Mater., 2004, 50, p 507–510CrossRef

22.

W.R. Osório, J.E. Spinelli, I.L. Ferreira, and A. Garcia, The Roles of Macrosegregation and of Dendritic Array Spacings on the Electrochemical Behavior of an Al-4.5 wt% Cu Alloy, Electrochim. Acta, 2007, 52, p 3265–3273CrossRef

23.

Yang Zhi-jun, Zhao Xiao-hua, and Kou Hong-chao, Numerical Simulation of Temperature Distribution and Heat Transfer During Solidification of Titanium Alloy Ingots in Vacuum Arc Remelting Process, Trans. Nonferrous Met. Soc. China, 2010, 20, p 1957–1962CrossRef

24.

C. Kenel and C. Leinenbach, Influence of Cooling Rate on Microstructure Formation During Rapid Solidification of Binary TiAl Alloys, J. Alloy. Compd., 2015, 637, p 242–247CrossRef

25.

B. Uhrenius, Calculation of the Ti-C, W-C and Ti-W-C Phase Diagrams, Calphad, 1984, 8(2), p 101–119CrossRef

26.

A.I. Gusev, Phase Equilibria, Phases and Chemical Compounds in the Ti-C System, Russ. Chem. Rev., 2002, 71(6), p 439–463CrossRef

27.

C.H. De Novion and J.P. Landesman, Order and Disorder in Transition Metal Carbides and Nitrides: Experimental and Theoretical Aspects, Pure Appl. Chem., 1985, 57(10), p 1391–1402CrossRef

28.

S.R. Shatynski, The Thermochemistry of Transition Metal Carbides, Oxid. Met., 1979, 13(2), p 105–118CrossRef

29.

N.S. Stoloff, Iron Aluminides: Present Status and Future Prospects, Mater. Sci. Eng., A, 1998, 258, p 1–14CrossRef

30.

M. Palm, Concepts Derived from Phase Diagram Studies for the Strengthening of Fe-Al Based Alloys, Intermetallics, 2005, 13, p 1286–1295CrossRef

31.

U. Prakash, K. Muraleedharan, R.A. Buckley, H. Jones, and P.A. Shenton, Effect of Ti Substitution on the Structure and Properties of Fe₃Al-Based Intermetallic Alloys, J. Mater. Sci., 1996, 31, p 1569–1573CrossRef

32.

A. Boutaghane, A. Hammouda, M. Zergoug, Y. Benkedda, M. Bouafia, K. Bouhadel, Thermal Distribution in Electrical Arc Welding of Tungsten Inert Gas (TIG) Process, 17th European Conference on Thermophysical Properties, Bratislava 2005, 5–8 September 2005, Bratislava Slovakia

33.

M.G. Mendiratta, S.K. Ehlers, and H.A. Lipsitt, DO3-B2-α Phase Relations in Fe-Al-Ti Alloys, Metall. Trans. A, 1987, 18, p 509–518CrossRef

34.

K.A. Jackson, Crystal Growth Kinetics, Mater. Sci. Eng., 1984, 65, p 7–13CrossRef

35.

K.A. Jackson, The Interface Kinetics of Crystal Growth Processes, Interface Sci., 2002, 10, p 159–169CrossRef

36.

H. Assadi, M. Barth, A.L. Greer, and D.M. Herlach, Kinetics of Intermetallic Compounds in the Ni-Al System, Acta Mater., 1998, 46(2), p 491–500CrossRef

37.

H. Assadi, S. Reutzel, and D.M. Herlach, Kinetics of Solidification of B2 Intermetallic Phase in the Ni-Al System, Acta Mater., 2006, 54, p 2793–2800CrossRef

38.

O. Hunziker and W. Kurz, Solidification Microstructure Maps in Ni-Al Alloys, Acta Mater., 1997, 45(12), p 4981–4992CrossRef

39.

S.H. Song, S.H. Kim, M.H. Oh, J.H. Lee, and D.M. Wee, Effects of Ternary Elements on Phase Transformation and Microstructure of NiAl/Ni₃Al Two-Phase Alloys, Intermetallics, 2005, 13, p 203–2010CrossRef

40.

J. Li, Y.L. Tang, N. Shen, and W. Pan, Effects of Solidification Kinetics on Phase Selection of Ni-Al Alloys, J. Alloy. Compd., 2001, 329, p 157–161CrossRef

41.

U.D. Hangen and G. Sauthoff, The Effect of Martensite Formation on the Mechanical Behaviour of NiAl, Intermetallics, 1999, 7, p 501–510CrossRef

Titel: Fabrication of TiC-Reinforced Composites by Vacuum Arc Melting: TiC Mode of Reprecipitation in Different Molten Metals and Alloys
verfasst von: A. E. Karantzalis
Z. Arni
K. Tsirka
A. Evangelou
A. Lekatou
V. Dracopoulos
Publikationsdatum: 28.06.2016
Verlag: Springer US
Erschienen in: Journal of Materials Engineering and Performance / Ausgabe 8/2016
Print ISSN: 1059-9495
Elektronische ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-016-2195-0

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 8/2016

Mechanical Properties of Solid-State Recycled 4xxx Aluminum Alloy Chips

Observation of Pseudopartial Grain Boundary Wetting in the NdFeB-Based Alloy

Microstructure Changes and Phase Growth Occurring at the Interface of the Al/Ti Explosively Welded and Annealed Joints

FEM Simulation and Experimental Validation of LBW Under Conduction Regime of Ti6Al4V Alloy

Thermal and Microstructure Characterization of Zn-Al-Si Alloys and Chemical Reaction with Cu Substrate During Spreading

Effect of La2O3 Nanoparticles on the Brazeability, Microstructure, and Mechanical Properties of Al-11Si-20Cu Alloy

Premium Partner

Marktübersichten