Skip to main content
Fachgebiete
Automobil + Motoren Bauwesen + Immobilien Business IT + Informatik Elektrotechnik + Elektronik Energie + Nachhaltigkeit Finance + Banking Management + Führung Marketing + Vertrieb Maschinenbau + Werkstoffe Versicherung + Risiko
DE
EN
Bücher
Zeitschriften
Themenseiten
Organisationspsychologie Projektmanagement Marketing Smart Manufacturing
Weitere Formate
Podcasts Webinare Technik Webinare Wirtschaft Kongresse Veranstaltungskalender Awards
Jetzt Einzelzugang starten
Zugang für Unternehmen
Referenzkunden
SLX-Digitalkonferenz: Zukunftswerkstatt 2024

Mehr Umsatz mit Top-Kontakten

Am 7. Mai erfahren Sie, wie Vertriebsteams Leadgenerierung, Leadnurturing und Leadstrategien effizient steuern können.
Erweiterte Suche
Anmelden
nach oben
Tribology Letters
Erschienen in: Tribology Letters 3/2021

01.09.2021 | Original Paper

Influence of Sample Tilt and Applied Load on Microscratch Behavior of Copper Under a Spherical Diamond Indenter

verfasst von: Ming Liu

Erschienen in: Tribology Letters | Ausgabe 3/2021

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config
loading …

Abstract

Microscratch test with a spherical indenter was carried out on copper under different tilt conditions and applied loads. Influence of surface slope and applied load on scratch responses such as friction coefficient, residual groove width, penetration depth was quantified by simple (e.g., linear, quadratic, and power-law) expressions. Apparent friction coefficient for non-tilt condition can be obtained by correcting the results measured for a prior known surface slope. Contact area is believed to be confined in the front side of the indenter with pile-up of material contributing to the horizontally projected area and a minor segment for the vertically projected area. The radius of spherical indenter can be calibrated on a reference material from residual groove width and penetration depth data.
Vorheriger Artikel Influence of Base oil Polarity on the Tribological Performance of Surface-Active Engine Oil Additives
Nächster Artikel Tailorable and Repeatable Normal Contact Stiffness via Micropatterned Interfaces

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

  • über 102.000 Bücher
  • über 537 Zeitschriften

aus folgenden Fachgebieten:

  • Automobil + Motoren
  • Bauwesen + Immobilien
  • Business IT + Informatik
  • Elektrotechnik + Elektronik
  • Energie + Nachhaltigkeit
  • Finance + Banking
  • Management + Führung
  • Marketing + Vertrieb
  • Maschinenbau + Werkstoffe
  • Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

  • über 67.000 Bücher
  • über 390 Zeitschriften

aus folgenden Fachgebieten:

  • Automobil + Motoren
  • Bauwesen + Immobilien
  • Business IT + Informatik
  • Elektrotechnik + Elektronik
  • Energie + Nachhaltigkeit
  • Maschinenbau + Werkstoffe




 

Jetzt Wissensvorsprung sichern!

Jetzt informieren
Literatur
1.
Menezes, P.L., Kailas, S.V.: Effect of roughness parameter and grinding angle on coefficient of friction when sliding of Al–Mg alloy over EN8 steel. J. Tribol. 128, 10–14 (2006)CrossRef
2.
Zhang, X., Li, Z., Wang, J.: Friction prediction of rolling-sliding contact in mixed EHL. Measurement 100, 262–269 (2017)CrossRef
3.
Sabat, R.K., SuryaPavan, M.V., Aakash, D.S., Kumar, M., Sahoo, S.K.: Mechanism of texture and microstructure evolution during warm rolling of Ti–6Al–4V alloy. Philos. Mag. 98, 2562–2581 (2018)CrossRef
4.
Liu, C.S., Zheng, Z.Y., Wu, D.W., Ye, M.S., Gao, P., Peng, Y.G., et al.: Sliding friction and wear properties of CN X /TiN composite films. Tribol. Int. 37, 721–725 (2004)CrossRef
5.
Iliuc, I.: Wear and micropitting of steel ball sliding against TiN coated steel plate in dry and lubricated conditions. Tribol. Int. 39, 607–615 (2006)CrossRef
6.
Ceschini, L., Palombarini, G., Sambogna, G., Firrao, D., Scavino, G., Ubertalli, G.: Friction and wear behaviour of sintered steels submitted to sliding and abrasion tests. Tribol. Int. 39, 748–755 (2006)CrossRef
7.
Jianxin, D., Jianhua, L., Jinlong, Z., Wenlong, S., Ming, N.: Friction and wear behaviors of the PVD ZrN coated carbide in sliding wear tests and in machining processes. Wear 264, 298–307 (2008)CrossRef
8.
Archard, J.F.: Elastic deformation and the laws of friction. Procrsoclonda 24, 190–205 (1957)
9.
Menezes, P.L., Kailas, S.V.: Effect of surface topography on friction and transfer layer during sliding. Tribology 3, 25–30 (2008)
10.
Moore, M.A., King, F.S.: Abrasive wear of brittle solids. Wear 60, 123–140 (1980)CrossRef
11.
Hiratsuka, K., Enomoto, A., Sasada, T.: Friction and wear of Al2O3, ZrO2 and SiO2 rubbed against pure metals. Wear 153, 361–373 (1992)CrossRef
12.
Mokhtar, M.O.A., Zaki, M., Shawki, G.S.A.: Correlation between the frictional behaviour and the physical properties of metals. Wear 65, 29–34 (1980)CrossRef
13.
Yoon, E.S., Kong, H., Kwon, O.K., Oh, J.E.: Evaluation of frictional characteristics for a pin-on-disk apparatus with different dynamic parameters. Wear s 203–204, 341–349 (1997)CrossRef
14.
Liu, Y., Wang, W., Zhang, H., Zhao, Z.: Solution of temperature distribution under frictional heating with consideration of material inhomogeneity. Tribol. Int. 126, 80–96 (2018)CrossRef
15.
Udaykant Jadav, P., Amali, R., Adetoro, O.B.: Analytical friction model for sliding bodies with coupled longitudinal and transverse vibration. Tribol. Int. 126, 240–248 (2018)CrossRef
16.
Lafaye, S., Gauthier, C., Schirrer, R.: The ploughing friction: analytical model with elastic recovery for a conical tip with a blunted spherical extremity. Tribol. Lett. 21, 95–99 (2006)CrossRef
17.
Thakre, A.A., Singh, A.K.: Frictional study of the soft and hard solid interface using response surface methodology. J. Tribol. 140, 1601 (2018)CrossRef
18.
Zhang, N., Li, C., Lu, A., Chen, X., Liu, D., Zhu, E.: Experimental studies on the basic friction angle of planar rock surfaces by tilt test. J. Testing Eval. 47, 256–283 (2019)
19.
Wu, J., Wu, G., Kou, X., Lu, Z., Zhang, G., Wu, Z.: Probing tribological behaviors of Cr-DLC in corrosion solution by tailoring sliding interface. Tribol. Lett. 68, 95 (2020)CrossRef
20.
Liu, M., Yang, F.: Finite element analysis of the indentation-induced delamination of Bi-layer structures. J. Comput. Theor. Nanosci. 9, 235–238 (2012)CrossRef
21.
Liu, M., Yang, F.: Three-dimensional finite element simulation of the Berkovich indentation of a transversely isotropic piezoelectric material: effect of material orientation. Modell Simul. Mater. Sci. Eng. 21, 045014 (2013)CrossRef
22.
Subhash, G., Zhang, W.: Investigation of the overall friction coefficient in single-pass scratch test. Wear 252, 123–134 (2002)CrossRef
23.
Liu, D., Wang, Q., Zhang, D., Wang, J., Zhang, X.: Torsional friction behavior of contact interface between PEEK and CoCrMo in calf serum. J. Tribol. 141, 011612 (2018)
24.
Shi, H., Atkinson, M.: A friction effect in low-load hardness testing of copper and aluminium. J. Mater. Sci 25, 2111–2114 (1990)CrossRef
25.
Pelletier, H., Gauthier, C., Schirrer, R.: Influence of the friction coefficient on the contact geometry during scratch onto amorphous polymers. Wear 268, 1157–1169 (2010)CrossRef
26.
Zhan, J., Fard, M.: Effects of helix angle, mechanical errors, and coefficient of friction on the time-varying tooth-root stress of helical gears. Measurement 118, 135–146 (2018)CrossRef
27.
Niemczewska-Wójcik, M., Wójcik, A.: The machining process and multi-sensor measurements of the friction components of total hip joint prosthesis. Measurement 116, 56–67 (2018)CrossRef
28.
Nieminen, I., Andersson, P., Holmberg, K.: Friction measurement by using a scratch test method. Wear 130, 167–178 (1989)CrossRef
29.
Xie, Y., Hawthorne, H.M.: On the possibility of evaluating the resistance of materials to wear by ploughing using a scratch method. Wear 240, 65–71 (2000)CrossRef
30.
Jardret, V., Zahouani, H., Loubet, J.L., Mathia, T.G.: Understanding and quantification of elastic and plastic deformation during a scratch test. Wear 218, 8–14 (1998)CrossRef
31.
Liu, Z., Sun, J., Shen, W.: Study of plowing and friction at the surfaces of plastic deformed metals. Tribol. Int. 35, 511–522 (2002)CrossRef
32.
Kumar, A., Staedler, T., Jiang, X.: Effect of normal load and roughness on the nanoscale friction coefficient in the elastic and plastic contact regime. Beilstein J. Nanotechnol. 4, 66–71 (2013)CrossRef
33.
Bhushan, B., Kulkarni, A.V.: Effect of normal load on microscale friction measurements. Thin Solid Films 278, 49–56 (1996)CrossRef
34.
Dube, N.B., Hutchings, I.M.: Influence of particle fracture in the high-stress and low-stress abrasive wear of steel. Wears 233–235, 246–256 (1999)CrossRef
35.
Nahvi, S.M., Shipway, P.H., Mccartney, D.G.: Particle motion and modes of wear in the dry sand–rubber wheel abrasion test. Wear 267, 2083–2091 (2009)CrossRef
36.
Stevenson, A.N.J., Hutchings, I.M.: Development of the dry sand/rubber wheel abrasion test. Wear 195, 232–240 (1996)CrossRef
37.
Salah, N., Abdel-wahab, M.S., Habib, S.S., Khan, Z.H.: Lubricant additives based on carbon nanotubes produced from carbon-rich fly ash. Tribol. Trans. 60, 166–175 (2017)CrossRef
38.
Gao, C., Liu, M.: Effects of normal load on the coefficient of friction by microscratch test of copper with a spherical indenter. Tribol. Lett. 67, 8 (2019)CrossRef
39.
Maegawa, S., Itoigawa, F., Nakamura, T.: Effect of normal load on friction coefficient for sliding contact between rough rubber surface and rigid smooth plane. Tribol. Int. 92, 335–343 (2015)CrossRef
40.
Ghasemi, R., Johansson, J., Ståhl, J.-E., Jarfors, A.E.W.: Load effect on scratch micro-mechanisms of solution strengthened compacted graphite irons. Tribol. Int. 133, 182–192 (2019)CrossRef
41.
Riehm, P., Unrau, H.J., Gauterin, F.: A model based method to determine rubber friction data based on rubber sample measurements. Tribol. Int. 127, 37–46 (2018)CrossRef
42.
Yoshizumi, F., Tani, H., Sanda, S.: Simulation of the friction coefficient of paper-based wet clutch with wavy separators. J. Tribol. 141, 011702-011702–011713 (2018)
43.
Tiwary, C.S., Prakash, J., Chakraborty, S., Mahapatra, D.R., Chattopadhyay, K.: Subsurface deformation studies of aluminium during wear and its theoretical understanding using molecular dynamics. Philos. Mag. 98, 2680–2700 (2018)CrossRef
44.
Jeon, S., Thundat, T., Braiman, Y.: Effect of normal vibration on friction in the atomic force microscopy experiment. Appl. Phys. Lett. 88, 214102-214102–214103 (2006)CrossRef
45.
Hu, Z.M., Dean, T.A.: A study of surface topography, friction and lubricants in metalforming. Int. J. Mach. Tools Manuf. 40, 1637–1649 (2000)CrossRef
46.
Zhang, H., Takeuchi, Y., Chong, W.W.F., Mitsuya, Y., Fukuzawa, K., Itoh, S.: Simultaneous in situ measurements of contact behavior and friction to understand the mechanism of lubrication with nanometer-thick liquid lubricant films. Tribol. Int. 127, 138–146 (2018)CrossRef
47.
Zhou, C., Hu, B., Qian, X., Han, X.: A novel prediction method for gear friction coefficients based on a computational inverse technique. Tribol. Int. 127, 200–208 (2018)CrossRef
48.
Wang, J., Ma, L., Li, W., Zhou, Z.: Influence of different lubricating fluids on friction trauma of small intestine during enteroscopy. Tribol. Int. 126, 29–38 (2018)CrossRef
49.
Chun, L., Zhongyi, M., Fubao, Z., Chen, K., Haiyang, Y.: The wear and friction characters of polycrystalline diamond under wetting conditions. J. Tribol. 141, 021607 (2018)
50.
Alakhramsing, S.S., de Rooij, M.B., Akchurin, A., Schipper, D.J., van Drogen, M.: A mixed-TEHL analysis of cam-roller contacts considering roller slip: on the influence of roller-pin contact friction. J. Tribol. 141, 011503-011503–011515 (2018)
51.
AhmedAli, M.K., Xianjun, H., Essa, F.A., Abdelkareem, M.A.A., Elagouz, A., Sharshir, S.W.: Friction and wear reduction mechanisms of the reciprocating contact interfaces using nanolubricant under different loads and speeds. J. Tribol. 140, 051606-051606–051610 (2018)
52.
Cozza, R.C.: Influence of the normal force, abrasive slurry concentration and abrasive wear modes on the coefficient of friction in ball-cratering wear tests. Tribol. Int. 70, 52–62 (2014)CrossRef
53.
Li, D., Liu, Y., Deng, Y., Fang, M., Wu, D.: The effect of different temperatures on friction and wear properties of CFRPEEK against AlSi 431 steel under water lubrication. Tribol. Trans. 61, 357–366 (2018)CrossRef
54.
Kato, K.: Wear in relation to friction—a review. Wear 241, 151–157 (2000)CrossRef
55.
Rymuza, Z.: Energy concept of the coefficient of friction. Wear 199, 187–196 (1996)CrossRef
56.
Hartung, F., Kienle, R., Götz, T., Winkler, T., Ressel, W., Eckstein, L., et al.: Numerical determination of hysteresis friction on different length scales and comparison to experiments. Tribol. Int. 127, 165–176 (2018)CrossRef
57.
Saravanan, P., Selyanchyn, R., Watanabe, M., Fujikawa, S., Tanaka, H., Lyth, S.M., et al.: Ultra-low friction of polyethylenimine/molybdenum disulfide (PEI/MoS2)15 thin films in dry nitrogen atmosphere and the effect of heat treatment. Tribol. Int. 127(255), 263 (2018)
58.
Menezes, P.L., Kishore Kailas, S.V., Bobji, M.S.: Influence of tilt angle of plate on friction and transfer layer—A study of aluminium pin sliding against steel plate. Tribol. Int. 43, 897–905 (2010)CrossRef
59.
Staph, H.E., Ku, P.M., Carper, H.J.: Effect of surface roughness and surface texture on scuffing. Mech. Mach. Theory 8, 197–208 (1973)CrossRef
60.
Lakshmipathy, R., Sagar, R.: Effect of die surface topography on die-work interfacial friction in open die forging. Int. J. Mach. Tools Manuf. 32, 685–693 (1992)CrossRef
61.
Menezes, P.L., KishoreKailas, S.V.: Studies on friction and transfer layer using inclined scratch. Tribol. Int. 39, 175–183 (2006)CrossRef
62.
Määttä, A., Vuoristo, P., Mäntylä, T.: Friction and adhesion of stainless steel strip against tool steels in unlubricated sliding with high contact load. Tribol. Int. 34, 779–786 (2001)CrossRef
63.
Malayappan, S., Narayanasamy, R.: An experimental analysis of upset forging of aluminium cylindrical billets considering the dissimilar frictional conditions at flat die surfaces. Int. J. Adv. Manuf. Technol. 23, 636–643 (2004)CrossRef
64.
Wakuda, M., Yamauchi, Y., Kanzaki, S., Yasuda, Y.: Effect of surface texturing on friction reduction between ceramic and steel materials under lubricated sliding contact. Wear 254, 356–363 (2003)CrossRef
65.
Tripathi, K., Gyawali, G., Amanov, A., Lee, S.W.: Synergy effect of ultrasonic nanocrystalline surface modification and laser surface texturing on friction and wear behavior of graphite cast iron. Tribol. Trans. 60, 226–237 (2017)CrossRef
66.
Seo, N.J., Armstrong, T.J.: Friction coefficients in a longitudinal direction between the finger pad and selected materials for different normal forces and curvatures. Ergonomics 52, 609–616 (2009)CrossRef
67.
Gao, C., Yao, L., Liu, M.: Measurement of sample tilt by residual imprint morphology of Berkovich indenter. J. Testing Eval. 48, 4 (2020)
68.
Sinha, S.K., Lim, D.B.J.: Effects of normal load on single-pass scratching of polymer surfaces. Wear 260, 751–765 (2006)CrossRef
69.
Feng, B.: Tribology behavior on scratch tests: Effects of yield strength. Friction 5, 108–114 (2017)CrossRef
70.
Gong, F., Guo, B.: Effects of influencing factors on friction coefficient in microsheet forming. Mater. Res. Innovations 17, 7–11 (2013)CrossRef
71.
Xu, M., Li, L., Wang, M., Luo, B.: Effects of surface roughness and wood grain on the friction coefficient of wooden materials for wood-wood frictional pair. Tribol. Trans. 57, 871–878 (2014)CrossRef
72.
Han, L., Zhang, D.-W., Wang, F.-J.: Predicting film parameter and friction coefficient for helical gears considering surface roughness and load variation. Tribol. Trans. 56, 49–57 (2013)CrossRef
73.
Gao, C., Proudhon, H., Liu, M.: Three-dimensional finite element analysis of shallow indentation of rough strain-hardening surface. Friction 7, 587–602 (2019)CrossRef
74.
Jiang, H., Browning, R., Fincher, J., Gasbarro, A., Jones, S., Sue, H.-J.: Influence of surface roughness and contact load on friction coefficient and scratch behavior of thermoplastic olefins. Appl. Surf. Sci. 254, 4494–4499 (2008)CrossRef
75.
Menezes, P.L., Kishore Kailas, S.V.: Studies on friction and transfer layer: role of surface texture. Tribol. Lett. 24, 265–273 (2006)CrossRef
76.
Torrance, A.A.: Using profilometry for the quantitative assessment of tribological function: PC-based software for friction and wear prediction. Wear 181–183, 397–404 (1995)CrossRef
77.
Bhushan, B., Nosonovsky, M.: Scale effects in dry and wet friction, wear, and interface temperature. Nanotechnology 15, 749 (2004)CrossRef
78.
Gao, C., Yao, L., Zheng, R., Liu, M.: Effect of sample tilt on spherical indentation of an elastic solid. J. Test. Eval. 47, 2596–2612 (2019)CrossRef
79.
Black, A.J., Kopalinsky, E.M., Oxley, P.L.B.: An investigation of the different regimes of deformation which can occur when a hard wedge slides over a soft surface: the influence of wedge angle, lubrication and prior plastic working of the surface. Wear 123, 97–114 (1988)CrossRef
80.
Pondicherry, K., Rajaraman, D., Galle, T., Hertelé, S., Fauconnier, D., De Baets, P.: Optimization and validation of a load-controlled numerical model for single asperity scratch. Tribol. Lett. 68, 45 (2020)CrossRef
81.
Maas, P., Mizumoto, Y., Kakinuma, Y., Min, S.: Anisotropic brittle-ductile transition of monocrystalline sapphire during orthogonal cutting and nanoindentation experiments. Nanotechnol. Precis Eng. 1, 157–171 (2018)CrossRef
82.
Tseng, A.A.: A comparison study of scratch and wear properties using atomic force microscopy. Appl Surf Sci 256, 4246–4252 (2010)CrossRef
83.
(!!! INVALID CITATION !!! [63–66]).
84.
Ranjan, P., Balasubramaniam, R., Jain, V.K.: Investigations into the mechanism of material removal and surface modification at atomic scale on stainless steel using molecular dynamics simulation. Phil. Mag. 98, 1437–1469 (2018)CrossRef
85.
Liu, M., Li, S., Gao, C.: Fracture toughness measurement by micro-scratch tests with conical indenter. Tribology 39, 556–564 (2019)
86.
Tabor, A.: The physical meaning of indentation and scratch hardness. Br. J. Appl. Phys. 7, 159–166 (1956)CrossRef
87.
Williams, J.A.: Analytical models of scratch hardness. Tribol. Int. 29, 675–694 (1996)CrossRef
88.
Huang, L., Xu, K., Lu, J., Guelorget, B., Chen, H.: Nano-scratch and fretting wear study of DLC coatings for biomedical application. Diam. Relat. Mater. 10, 1448–1456 (2001)CrossRef
89.
Wu, T.W.: Microscratch and load relaxation tests for ultra-thin films. J Mater Res 6, 407–426 (1991)CrossRef
90.
Venkataraman, S., Kohlstedt, D.L., Gerberich, W.W.: Microscratch analysis of the work of adhesion for Pt thin films on NiO. J. Mater. Res. 7, 1126–1132 (1992)CrossRef
91.
Li, X., Bhushan, B.: Micro/nanomechanical and tribological characterization of ultrathin amorphous carbon coatings. J. Mater. Res. 14, 2328–2337 (1999)CrossRef
92.
Yan, J., Lindo, A., Schwaiger, R., Hodge, A.M.: Sliding wear behavior of fully nanotwinned Cu alloys. Friction 7, 260–267 (2018)CrossRef
93.
Wei, Y., Nixon, W., Shi, Z.: Evaluation of wear resistance of snow plow blade cutting edges using the scratch test method. J. Test. Eval. 26, 527–531 (1998)CrossRef
94.
Yazdi, R., Ghasemi, H.M., Abedini, M., Wang, C., Neville, A.: Oxygen diffusion layer on Ti–6Al–4V alloy: scratch and dry wear resistance. Tribol. Lett. 67, 101 (2019)CrossRef
95.
Sakamoto, T., Tsukizoe, T.: Friction and prow formation in a scratch process of copper by a diamond cone. Wear 44, 393–403 (1977)CrossRef
96.
Zhang, F., Meng, B., Geng, Y., Zhang, Y., Li, Z.: Friction behavior in nanoscratching of reaction bonded silicon carbide ceramic with Berkovich and sphere indenters. Tribol. Int. 97, 21–30 (2016)CrossRef
97.
Wo, P.C., Ngan, A.H.W.: Incipient plasticity during nano-scratch in Ni3Al. Philos. Mag. 84, 3145–3157 (2004)CrossRef
98.
Deng, H., Scharf, T.W., Barnard, J.A.: Adhesion assessment of silicon carbide, carbon, and carbon nitride ultrathin overcoats by nanoscratch techniques. J. Appl. Phys. 81, 5396–5398 (1997)CrossRef
99.
Burnett, P.J., Rickerby, D.S.: The scratch adhesion test: an elastic-plastic indentation analysis. Thin Solid Films 157, 233–254 (1988)CrossRef
100.
Sekler, J., Steinmann, P.A., Hintermann, H.E.: The scratch test: different critical load determination techniques. Surf. Coat Technol. 36, 519–529 (1988)CrossRef
101.
Staia, M.H., Puchi, E.S., Schmutz, C.J.: Adhesion of CVD tin on 316l surgical stainless steel obtained in a mass transfer regime. J. Electron. Mater. 26, 980–986 (1997)CrossRef
102.
Palesch, E., Cech, V.: Characterization of interlayer adhesion on single glass fibers and planar glass using the nanoscratch test technique. Thin Solid Films 636, 353–358 (2017)CrossRef
103.
Xu, K., Hu, N., He, J.: Evaluation of the bond strength of hard coatings by the contact fatigue test. J. Adhes. Sci. Technol. 12, 1055–1069 (1998)CrossRef
104.
105.
Liu, M., Zhu, G., Dong, X., Liao, J., Gao, C.: Effects of sample tilt on vickers indentation hardness. In: Yao, L., Zhong, S., Kukuta, H., Juang, J.G. (eds.) Advanced Mechanical Science and Technology for the Industrial Revolution 40 FZU 2016, pp. 271–283. Springer, New York (2018)
106.
Xu, Z.H., Li, X.: Effect of sample tilt on nanoindentation behaviour of materials. Philos. Mag. 87, 2299–2312 (2007)CrossRef
107.
Kashani, M.S., Madhavan, V.: Analysis and correction of the effect of sample tilt on results of nanoindentation. Acta Mater. 59, 883–895 (2011)CrossRef
108.
Huang, H., Zhao, H., Shi, C., Zhang, L.: Using residual indent morphology to measure the tilt between the triangular pyramid indenter and the sample surface. Meas. Sci. Technol. 24, 105602–105607 (2013)CrossRef
109.
Shi, C., Zhao, H., Huang, H., Xu, L., Ren, L., Bai, M., et al.: Effects of indenter tilt on nanoindentation results of fused silica: an investigation by finite element analysis. Mater. Trans. 54, 958–963 (2013)CrossRef
110.
Shi, C., Zhao, H., Huang, H., Wan, S., Ma, Z., Geng, C., et al.: Effects of probe tilt on nanoscratch results: an investigation by finite element analysis. Tribol. Int. 60, 64–69 (2013)CrossRef
111.
Huang, L.Y., Xu, K.W., Lu, J.: Evaluation of scratch resistance of diamond-like carbon films on Ti alloy substrate by nano-scratch technique. Diam. Relat. Mater. 11, 1505–1510 (2002)CrossRef
112.
Charitidis, C., Logothetidis, S., Gioti, M.: A comparative study of the nanoscratching behavior of amorphous carbon films grown under various deposition conditions. Surf. Coat. Technol. 125, 201–206 (2000)CrossRef
113.
Zhang, D., Sun, Y., Gao, C., Liu, M.: Measurement of fracture toughness of copper via constant-load microscratch with a spherical indenter. Wear 444–445, 203158 (2020)CrossRef
114.
Gao, C., Liu, M.: Effect of sample tilt on measurement of friction coefficient by constant-load scratch testing of copper with a spherical indenter. J. Test. Eval. 48, 20180719 (2020)CrossRef
115.
Liu, M., Wu, J., Cao, C.: Sliding of a diamond sphere on K9 glass under prograssive load. J. Non-Cryst. Solid 526, 119711 (2019)CrossRef
116.
Akono, A.T., Randall, N.X., Ulm, F.J.: Experimental determination of the fracture toughness via microscratch tests: application to polymers, ceramics, and metals. J. Mater. Res. 27, 485–493 (2012)CrossRef
117.
Mcadams, S.D., Tsui, T.Y., Oliver, W.C., Pharr, G.M.: Effects of interlayers on the scratch adhesion performance of ultra-thin films of copper and gold on silicon substrates. MRS Online Proc. Library Arch. 356, 1 (1994)
118.
Liu, M., Huang, C., Gao, C.: Effect of sample tilt and normal load on micro-scratch test of copper with a spherical indenter. Tribology 41, 27–37 (2021)
119.
Gao, C., Liu, M.: Effects of normal load on the coefficient of friction by microscratch test of copper with a spherical indenter. Tribol. Lett. 67, 1–12 (2019)CrossRef
120.
Scharf, T.W., Barnard, J.A.: Nanotribology of ultrathin a:SiC/SiC-N overcoats using a depth sensing nanoindentation multiple sliding technique. Thin Solid Films 308, 340–344 (1997)CrossRef
121.
Li, K., Yuhong, B., Li, J.: Stick-slip in the scratching of styrene-acrylonitrile copolymer. J. Mater. Res. 11, 1574–1580 (1996)CrossRef
122.
Byerlee, J.D.: The mechanics of stick-slip. Tectnonophysics 9, 475–486 (1970)CrossRef
123.
Zhang, J., Wei, Y., Sun, T., Hartmaier, A., Yan, Y., Li, X.: Twin boundary spacing-dependent friction in nanotwinned copper. Phys. Rev. B 85, 054109 (2012)CrossRef
124.
Wo, P.C., Jones, I.P., Ngan, A.H.W.: TEM study of the deformation structures around nano-scratches. Phil. Mag. 88, 1369–1388 (2008)CrossRef
125.
Li, K., Shapiro, Y., Li, J.C.M.: Scratch test of soda-lime glass. Acta Mater. 46, 5569–5578 (1998)CrossRef
126.
Yamaguchi, T., Sugawara, T., Takahashi, M., Shibata, K., Moriyasu, K., Nishiwaki, T., et al.: Dry sliding friction of ethylene vinyl acetate blocks: effect of the porosity. Tribol. Int. 116, 264–271 (2017)CrossRef
127.
Almotasem, A.T., Bergström, J., Gåård, A., Krakhmalev, P., Holleboom, L.J.: Atomistic insights on the wear/friction behavior of nanocrystalline ferrite during nanoscratching as revealed by molecular dynamics. Tribol. Lett. 65, 101 (2017)CrossRef
128.
Lafaye, S., Gauthier, C., Schirrer, R.: A surface flow line model of a scratching tip: apparent and true local friction coefficients. Tribol. Int. 38, 113–127 (2005)CrossRef
129.
Flores, S.E., Pontin, M.G., Zok, F.W.: Scratching of elastic/plastic materials with hard spherical indenters. J. Appl. Mech. 75, 1055–1062 (2008)CrossRef
130.
Zhao, G., Liu, M., An, Z., Ren, Y., Liaw, P.K., Yang, F.: Electromechanical responses of Cu strips. J. Appl. Phys. 113, 183521 (2013)CrossRef
131.
Bowden, F.P., Tabor, D.: The friction and lubrication of solids. Clarendon (1950)
132.
Xiao, J.-K., Zhang, L., Zhou, K.-C., Wang, X.-P.: Microscratch behavior of copper–graphite composites. Tribol. Int. 57, 38–45 (2013)CrossRef
133.
Carreon, A.H., Funkenbusch, P.D. Material specific nanoscratch ploughing friction coefficient. Tribol. Int. (2018).
134.
Beegan, D., Chowdhury, S., Laugier, M.T.: Comparison between nanoindentation and scratch test hardness (scratch hardness) values of copper thin films on oxidised silicon substrates. Surf. Coat. Technol. 201, 5804–5808 (2007)CrossRef
135.
Cheng, Y.-T., Cheng, C.-M.: Scaling, dimensional analysis, and indentation measurements. Mater. Sci. Eng. R 44, 91–149 (2004)CrossRef
136.
Vander, V.G.F., Lucas, G.M.: Micro-indentation Hardness Testing. Butterworths Scientific (1956)
137.
Kese, K.O., Li, Z.C., Bergman, B.: Method to account for true contact area in soda-lime glass during nanoindentation with the Berkovich tip. Mater. Sci. Eng. A 404, 1–8 (2005)CrossRef
138.
Kese, K., Li, Z.C.: Semi-ellipse method for accounting for the pile-up contact area during nanoindentation with the Berkovich indenter. Scr. Mater. 55, 699–702 (2006)CrossRef
139.
Yan, Y.D., Sun, T., Dong, S.: Study on effects of tip geometry on AFM nanoscratching tests. Wear 262, 477–483 (2007)CrossRef
140.
Bucaille, J.L., Felder, E., Hochstetter, G.: Mechanical analysis of the scratch test on elastic and perfectly plastic materials with the three-dimensional finite element modeling. Wear 249, 422–432 (2001)CrossRef
141.
Kareer, A., Hou, X.D., Jennett, N.M., Hainsworth, S.V.: The existence of a lateral size effect and the relationship between indentation and scratch hardness in copper. Philos. Mag. 96, 3396–3413 (2016)CrossRef
142.
Kareer, A., Hou, X.D., Jennett, N.M., Hainsworth, S.V.: The interaction between Lateral size effect and grain size when scratching polycrystalline copper using a Berkovich indenter. Philos. Mag. 96, 3414–3429 (2016)CrossRef
143.
Liu, C., Liu, W., Xing, W.: An improved edge-based level set method combining local regional fitting information for noisy image segmentation. Signal Process. 130, 12–21 (2017)CrossRef
144.
Wu, Y., Song, Y., Zhou, H.: Edge detection of combustion flame images based on anisotropic mathematical morphology. Yi Qi Yi Biao Xue Bao/Chin. J. Sci. Instrum. 34, 1818–1825 (2013)
145.
Liu, H., Zhao, M., Lu, C., Zhang, J.: Characterization on the yield stress and interfacial coefficient of friction of glasses from scratch tests. Ceram. Int. (2019).
146.
Useinov, A.S., Useinov, S.S.: Scratch hardness evaluation with in-situ pile-up effect estimation. Philos. Mag. 92, 3188–3198 (2012)CrossRef
Metadaten
Titel
Influence of Sample Tilt and Applied Load on Microscratch Behavior of Copper Under a Spherical Diamond Indenter
verfasst von
Ming Liu
Publikationsdatum
01.09.2021
Verlag
Springer US
Erschienen in
Tribology Letters / Ausgabe 3/2021
Print ISSN: 1023-8883
Elektronische ISSN: 1573-2711
DOI
https://doi.org/10.1007/s11249-021-01466-2

Weitere Artikel der Ausgabe 3/2021

Tribology Letters 3/2021 Zur Ausgabe

Original Paper

Low Friction Mechanism Survey of Tungsten Disulfide by Using XRD, XPS, and XAFS

Original Paper

Probing the Rheological Properties of Liquids Under Conditions of Elastohydrodynamic Lubrication Using Simulations and Machine Learning

Original Paper

Elucidating the Onset of Plasticity in Sliding Contacts Using Differential Computational Orientation Tomography

Original Paper

A Simple Mechanistic Model for Friction of Rough Partially Lubricated Surfaces

Correction

Corrections to: Atomic Origins of Friction Reduction in Metal Alloys

Original Paper

Structurally Driven Environmental Degradation of Friction in MoS2 Films

Premium Partner

    Marktübersichten

    Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen. 

    Zur Marktübersicht
    Bildnachweise