nach oben

The International Journal of Advanced Manufacturing Technology

Erschienen in:

08.07.2020 | ORIGINAL ARTICLE

Influence of micro size titanium powder-mixed dielectric medium on surface quality measures in EDM process

verfasst von: Nguyen HuuPhan, T. Muthuramalingam, Ngo Ngoc Vu, Nguyen Quoc Tuan

Erschienen in: The International Journal of Advanced Manufacturing Technology | Ausgabe 3-4/2020

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

The enhancement of the surface quality measures is still attracting great research attentions in electrical discharge machining. In the present investigation, an analysis was made to improve the surface performance measures in EDM process with different tool electrodes such as titanium, copper, and graphite electrodes under dielectric medium mixed with micro size titanium particles. The surface roughness, hardness, white layer thickness, crack formation, and surface topography were considered as surface quality measures. From the experimental investigation, it has been observed that surface hardness could be improved significantly with titanium powder-mixed dielectric medium due to its ability of changing conductivity of machining zone with copper tool electrode. The electrical and thermal conductivity of tool electrode and powder materials can strongly affect the quality of the machined surface in EDM process.

Vorheriger Artikel An evolutionary algorithm recommendation method with a case study in flow shop scheduling

Nächster Artikel Simultaneous servo error pre-compensation and feedrate optimization with tolerance constraints using linear programming

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

GianlucaD’Urso CR (2016) The effects of electrode size and discharged power on micro-electro-discharge machining drilling of stainless steel. Adv Mechl Eng 8(5):1–12. https://doi.org/10.1177/1687814016648646 CrossRef

SujoyChakraborty SK, Dey V, Ghosh SK (2018) The phenomenon of surface modification by electro-discharge coating process: a review, 1830003. Surf Rev Lett, 25:5, 1830003. https://doi.org/10.1142/S0218625X18300034

Shard A, Shikha D, Gupta V, Garg MP (2018) Effect of B4C abrasive mixed into dielectric fluid on electrical discharge machining. J Braz Soc Mech Sci Eng 40:554. https://doi.org/10.1007/s40430-018-1474-0 CrossRef

Prihandana GS, Mahardika M, Sriani T (2020) Review micromachining in powder-mixed micro electrical discharge machining. Appl Sci 10:3795. https://doi.org/10.3390/app10113795 CrossRef

Lopes JC, Garcia MV, SilveiraVolpato R, de Mello HJ, Ribeiro FSF, de Angelo Sanchez LE, de Oliveira Rocha K, Neto LD, Aguiar PR, Bianchi EC (2019) Application of MQL technique using TiO2 nanoparticles compared to MQL simultaneous to the grinding wheel cleaning jet. Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-019-04760-5

de Martini Fernandes L, Lopes JC, Ribeiro FSF, Gallo R, Razuk HC, de Angelo Sanchez LE, de Aguiar PR, de Mello HJ, Bianch EC (2019) Thermal model for surface grinding application. Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-019-04101-6

Rodriguez RL, Lopes JC, Mancini SD, de Ângelo Sanchez LE, de Almeida Varasquim FMF, SilveiraVolpato R, de Mello HJ, de Aguiar PR, Bianchi EC (2019) Contribution for minimization the usage of cutting fluids in CFRP grinding. Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-019-03529-0

Yu Y-T, Hsieh S-F, Lin M-H, Huang J-W, Ou S-F (2020) Effects of gas-assisted perforated electrode with rotation on the machining efficiency of PMEDM of titanium. Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-019-04882-w

HuzaifaRaza M, Wasim A, Ali MA, Hussain S, Jahanzaib M (2018) Investigating the effects of different electrodes on Al6061-SiC-7.5 wt% during electric discharge machining. Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-018-2694-2

10.

Abu Qudeiri JE, Saleh A, Ziout A, Mourad A-HI, Abidi MH, Elkaseer A (2019) Advanced electric discharge machining of stainless steels: assessment of the state of the art, gaps and future prospect. Materials 12:907. https://doi.org/10.3390/ma12060907 CrossRef

11.

Dewangan S, Biswas CK, Gangopadhyay S (2014) Influence of different tool electrode materials on EDMed surface integrity of AISI P20 tool steel. Mater Manuf Process 29:1387–1394. https://doi.org/10.1080/10426914.2014.930892 CrossRef

12.

D’Urso G, Maccarini G, Ravasio C (2016) Influence of electrode material in micro-EDM drilling of stainless steel and tungsten carbide. Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-015-7010-9

13.

Abdulkareem S, Khan AA (2009) Mohamed Konneh, Reducing electrode wear ratio using cryogenic cooling during electrical discharge machining. Int J AdvManufTechnol 45:1146–1151. https://doi.org/10.1007/s00170-009-2060-5 CrossRef

14.

Marafona JD (2009) Black layer affects the thermal conductivity of the surface of copper–tungsten electrode. Int J AdvManufTechnol 42:482–488. https://doi.org/10.1007/s00170-008-1613-3 CrossRef

15.

D’Urso G, Merla C (2014) Workpiece and electrode influence on micro-Edm drilling performance. Precis Eng. https://doi.org/10.1016/j.precisioneng.2014.05.007

16.

Khan AA, Ndaliman MB, Soot HBM, Ishak NB (2012) Influence of thermal conductivity of electrodes on EDM process parameters. Aust J Basic Appl Sci 6(9):337–345

17.

Liu Y, Wang W, Zhang W, Ma F, Wang Y, Rolfe B, Zhang S (2018) Study on breakdown probability of multimaterial electrodes in EDM. Adv Mater Sci Eng 2961879:1–8. https://doi.org/10.1155/2018/2961879 CrossRef

18.

Bhaumik M, Maity K (2019) Effect of electrode materials on different EDM aspects of titanium alloy. Silicon. https://doi.org/10.1007/s12633-018-9844-x

19.

Muthuramalingam T, Ramamurthy A, Sridharan K, Ashwin S (2018) Analysis of surface performance measures on WEDM processed titanium alloy with coated electrodes. Mater Res Express 5(12):126503CrossRef

20.

Geethapriyan T, Kalaichelvan K, Muthuramalingam T (2016) Influence of coated tool electrode on drilling Inconel alloy 718 in electrochemical micro machining. Procedia CIRP 46(1):127–130CrossRef

21.

Liu Q, Yang F, Sun S, Yang M, Shao J (2019) Surface integrity of micro EDM surface using electrodes of various diameters. Coatings 9:805. https://doi.org/10.3390/coatings9120805 CrossRef

22.

Muthuramalingam T (2019) Effect of diluted dielectric medium on spark energy in green EDM process using TGRA approach. J Clean Prod 238:117894CrossRef

23.

Panda DK, Bhoi RK Analysis of spark eroded crater formed under growing plasma channel in electro-discharge machining. Mach Sci Technol An Int J. https://doi.org/10.1081/MST-200059063

24.

Ahmed N, Anwar S, Ishfaq K, Rafaqat M, Saleh M, Ahmad S (2019) The potentiality of sinking eDM for micro-impressions on ti-6Al-4V: keeping the geometrical errors (axial and radial) and other machining measures (tool erosion and work roughness) at minimum. Sci Rep 9:17218. https://doi.org/10.1038/s41598-019-52855-6 CrossRef

25.

Schulze H-P, Herms R, Juhr H, Schaetzing W, Wollenberg G (2004) Comparison of measured and simulated crater morphology for EDM. J Mater Process Technol 149:316–322CrossRef

26.

Shabgard M, Oliaei SNB, Seyedzavvar M, Najadebrahimi A (2011) Experimental investigation and 3D finite element prediction of the white layer thickness, heat affected zone, and surface roughness in EDM process. J Mech Sci Technol 25(12):3173–3183. https://doi.org/10.1007/s12206&011&0905&y CrossRef

27.

Vijaykumar S. Jatti, ShivrajBagane, Thermo-electric modelling, simulation and experimental validation of powder mixed electric discharge machining (PMEDM) of BeCu alloys, Alexandria Eng J (2018) 57, 643–653

28.

Maher I, Sarhan AAD, Marashi H, Barzani MM, Hamdi M (2016) White layer thickness prediction in Wire-EDM using CuZn coated wire electrode - ANFIS modeling. Int J Surf Eng Coatings 94. https://doi.org/10.1080/00202967.2016.1180847

29.

Kumar A, Kumar V, Kumar J Surface crack density and recast layer thickness analysis in WEDM process through response surface methodology. Mach Sci Technol 20(2):201–230. https://doi.org/10.1080/10910344.2016.1165835

30.

Kumar A, Kumar V, Kumar J Microstructure analysis and material transformation of pure titanium and tool wear surface after wire electric discharge machining process. Mach Sci Technol 18:47–77. https://doi.org/10.1080/10910344.2014.863632

31.

Toshio Moro, Akihiro Goto, Nagao Saito, Naotake Mohri, ojiAkamatsu, Hisashi Yamada, Toshio Sata, Machining phenomena in EDM for surface modification with TiC semi-sintered electrode

32.

Das A, Mishra JP (2012) Experimental investigation on surface modification of aluminium by electric discharge coating process using TiC/Cu green compact tool electrode. J Mach Sci Technol 16-4:601–623CrossRef

33.

Hwang Y, Kuo C, Hwang S (2009) The coating of TiC layer on the surface of nickel by electric discharge coating (EDC) with a multi-layer electrode. J Mater Process Technol 210:642–652CrossRef

34.

Liew PJ, Yap CY, Wang J, Zhou T, Yan J (2020) Surface modification and functionalization by electrical discharge coating: a comprehensive review. Int J Extreme Manuf 2:1

35.

Luzia CAO, Laurindo CAH, Soares PC Jr, Torres RD, Mendes LA, Amorim FL Recast layer mechanical properties of tool steel after electrical discharge machining with silicon powder in the dielectric. Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-019-03549-w

36.

Bui VD, Mwangi JW, Meinshausen A-K, Mueller AJ, Bertrand J, Schubert A (2020) Antibacterial coating of Ti-6Al-4V surfaces using silver nano-powder mixed electrical discharge machining. Surf Coat Technol 383:125254CrossRef

37.

Muthuramalingam T, Mohan B, Jothilingam A (2014) Effect of tool electrode re-solidification on surface hardness in electrical discharge machining. Mater Manuf Process 29(11–12):1374–1380CrossRef

38.

Muthuramalingam T, Mohan B (2013) Influence of tool electrode properties on machinability in electrical discharge machining. Mater Manuf Process 28(8):939–943

39.

Bhattacharya A, Batish A, Singh K (2012) FE simulation and experimental validation of powder mixed edm process for estimating the temperature distribution and volume removed in single crater. Int J Model Sci Comput 03:1250006. https://doi.org/10.1142/S1793962312500067 CrossRef

40.

Hameed AS, Hamdoon FO, Jafar MS (2019) Influence of powder mixed EDM on the surface hardness of die steel. Mater Sci Eng 518:032030. https://doi.org/10.1088/1757-899X/518/3/032030 CrossRef

41.

Joshi AY, Joshi AY (2019) A systematic review on powder mixed electrical discharge machining. Heliyon 5:e02963CrossRef

42.

dos Santos RF, da Silva ER, Sales WF, Raslan AA (2017) Influence of the electrode material on the nitriding of medium carbon steel using sink electrical discharge machining. Int J AdvManufTechnol. https://doi.org/10.1007/s00170-016-9531-2

43.

Amorim FL, Dalcin VA, Soares P, Mendes LA (2017) Surface modification of tool steel by electrical discharge machining with molybdenum powder mixed in dielectric fluid. Int J Adv Manuf Technol 91:341–350. https://doi.org/10.1007/s00170-016-9678-x CrossRef

44.

Kumar A, Mandal A, Dixit AR, Das AK, Kumar S, Ranjan R (2018) Comparison in the performance of EDM and NPMEDM using Al2O3 nanopowder as an impurity in DI water dielectric. Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-018-3126-z

45.

Tang L, Ji Y, Ren L, Zhai KG, Huang TQ, Fan QM, Zhang JJ, Liu J (2019) Thermo-electrical coupling simulation of powder mixed EDM SiC/Al functionally graded materials. Int J Adv Manuf Technol 105:2615–2628CrossRef

46.

Ramesh S, Jenarthanan MP, BhuvaneshKanna AS (2018) Experimental investigation of powder-mixed electric discharge machining of AISI P20 steel using different powders and tool materials. Multidiscip Model Mater Struct 14:549–566. https://doi.org/10.1108/MMMS-04-2017-0025 CrossRef

47.

Hosni NAJ, Lajis MA (2019) Experimental investigation and economic analysis of surfactant (Span-20) in powder mixed electrical discharge machining (PMEDM) of AISI D2 hardened steel. Mach Sci Technol. https://doi.org/10.1080/10910344.2019.1698609

48.

Kumar H (2014) Development of mirror like surface characteristics using nano powder mixed electric discharge machining (NPMEDM). Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-014-5965-6

49.

Muthuramalingam T (2019) Measuring the influence of discharge energy on white layer thickness in electrical discharge machining process. Measurement 131:694–700CrossRef

50.

Kansal HK, Singhb S, Kumar P (2008) Numerical simulation of powder mixed electric discharge machining (PMEDM) using finite element method. Math Comput Model 47:1217–1237CrossRef

51.

Jadam T, Sahu SK, Datta S, Masanta M (2020) Powder-mixed electro-discharge machining performance of Inconel 718: effect of concentration of multi-walled carbon nanotube added to the dielectric media. Sådhanå 45:135. https://doi.org/10.1007/s12046-020-01378-2 CrossRef

Titel: Influence of micro size titanium powder-mixed dielectric medium on surface quality measures in EDM process
verfasst von: Nguyen HuuPhan
T. Muthuramalingam
Ngo Ngoc Vu
Nguyen Quoc Tuan
Publikationsdatum: 08.07.2020
Verlag: Springer London
Erschienen in: The International Journal of Advanced Manufacturing Technology / Ausgabe 3-4/2020
Print ISSN: 0268-3768
Elektronische ISSN: 1433-3015
DOI: https://doi.org/10.1007/s00170-020-05698-9

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 3-4/2020

Deformation behaviour and damage evolution of aluminium alloy sheet in electromagnetic forming with uniform pressure actuator

New knowledge about grinding using MQL simultaneous to cooled air and MQL combined to wheel cleaning jet technique

Investigation of load direction on the compressive strength of additively manufactured triply periodic minimal surface scaffolds

Numerical contribution to segmented chip effect on residual stress distribution in orthogonal cutting of Inconel718

Establishment of vibration wear model for turning large-pitch thread tools and its wear suppression method

An evolutionary algorithm recommendation method with a case study in flow shop scheduling

Premium Partner

Marktübersichten